ENKIN BYP001 Dimmer Switch Bypass Module User Manual
- June 16, 2024
- ENKIN
Table of Contents
ENKIN BYP001 Dimmer Switch Bypass Module
Product Information
Specifications:
- Operating Voltage: 220-240 V
- Nominal Operating Frequency: 50 Hz
- Max PC: 1W
- BS EN 60669-2-1 Bypass Module
- IP Rating: IP20
Product Usage Instructions
Safety Precautions:
Failure to follow these instructions can result in death or serious injury. It
is essential that this product is fitted by an experienced professional.
Wiring Diagram:
The product must be installed by a qualified and experienced electrician in
accordance with applicable current electrical regulations. Follow the provided
wiring diagram:
Installation Instructions
- Lock out and tag the input circuit before accessing the wiring connections.
- Install the device according to the instructions provided in this document.
- Pay attention to the specifications and wiring diagrams related to the installation.
- Do not use this product for any other purpose than specified in this instruction.
- The product is suitable for indoor use only.
- Apply an IEC60898-1 compliant 250V~ 6A MCB as an overload protective device.
Environmental Protection
Electrical rated loads and limits of the product should NEVER be exceeded at any time. Always isolate the electricity supply at its source (Distribution Board) before attempting any installation or maintenance.
Bypass Module
- A solution for residual glowing in lights after dimmers have been switched off.
- A possible solution for light flicker.
- Can sometimes reduce minimum dimming levels.
Technical parameters
| Operating Voltage | 220-240 V |
|---|---|
| Nominal Operating Frequency | 50 Hz |
| Max Power Consumption | 1W |
| Operating Temperature | 0°C to 40°C / 32°F to 104°F |
| Relative Humidity | 8% to 80% |
| Compliance | BS EN 60669-2-1 |
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
- Turn off all power supplying this equipment.
- Use a voltage tester of appropriate rating.
Failure to follow these instructions can result in death or serious injury. It is essential that this product is fitted by an experienced professional.
WIRING DIAGRAM
WARNING
RISK OF ELECTRIC SHOCK
- Hazardous voltage and electrical current may be present at the wire leads of this product even when the device is switched off.
- Lock out and tag the input circuit before accessing the wiring connections.
- This device must be installed by a qualified and experienced electrician in accordance with applicable current electrical regulation.
- To comply with all safety standards, the product must be used only for the purpose described in this instruction and must be installed in accordance with the wiring rules and regulation in the location where it is installed.
- There are no user serviceable parts inside the product.
Failure to follow these instructions can result in death or serious injury.
EQUIPMENT DAMAGE HAZARD
- Install the device according to instructions in this document.
- Pay attention to the specifications and wiring diagrams related to the installation.
- Do not use this product for any other purpose than specified in this instruction.
- The product is suitable for indoor use only.
- Apply IEC60898-1 compliant 250V~ 6A MCB as an overload protective device.
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
LEGAL DISCLAIMER
The installation of electrical products is inherently dangerous and can lead to serious injury or death. The products we sell MUST be installed by a qualified and experienced electrician in accordance with applicable current electrical regulation. Any advice, guidance or other information provided by Enkin on their website or within any of our publications cannot completely anticipate your situation and common sense must prevail. Products need to be checked prior to installation and regularly for damage and wear and tear. Products should be returned and not used if in any doubt of their integrity. Electrical rated loads and limits of a given product should NEVER be exceeded at any time. The electricity supply should always be isolated at its source (Distribution Board) before attempting any installation or maintenance.
No advice or information, whether oral or written, obtained by you from us or through the service, our employees, consultants and/or retailers shall create any warranty not expressly made herein. You agree to assume all and any risk resulting from the utilisation of information provided by Enkin. You also expressly agree not to hold us responsible for any damage, personal injury, death or loss resulting from your use of our information, service or regulatory compliant products.
Scan QR Code for more detailed technical information on this product www.enkin.com
Enkin is a trading name of Trade Ivy. Registered in England Number: 10809945. Copyright © 2021 All Rights Reserved Trade Ivy Limited, Unit 3C Latham Park, St Blazey Road, Par, PL24 2HY
FAQ’s
Can I install this product myself?
No, this product must be fitted by an experienced professional to ensure safety and proper installation.
Can I use this product outdoors?
No, this product is suitable for indoor use only.
What overload protective device should I use?
You should apply an IEC60898-1 compliant 250V~ 6A MCB as an overload protective device.
How should I dispose of this product?
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>