Enkin PDM010 DC 1-10V Dimmer Instructions
- June 16, 2024
- ENKIN
Table of Contents
Enkin PDM010 DC 1-10V Dimmer
Product Information
Specifications
- Operating Voltage: 240V AC ~ 50 Hz
- Max Load: 1000W
- Dimming Technique: DC 1-10V
- Compliance: BS EN 60669-2-1
- Load Symbol:
- Compatible Loads
- Max Load
- L
- DIM –
- DIM +
- DC 1-10V DIMMABLE DRIVER
- L1 +
- N
- LOAD
- N –
Product Usage Instructions
ON, OFF, and DIMMING Function
The dimmer switch is activated by pressing the dimmer shaft only. The
dimming function is controlled by rotating the dimmer shaft.
Warning
RISK OF ELECTRIC SHOCK: Hazardous voltage and electrical current may be
present at the wire leads of this product even when the device is switched
off. To ensure safety, lock out and tag the input circuit before accessing the
wiring connections. This device must be installed by a qualified and
experienced electrician per applicable current electrical regulations. The
product must be used only for the purpose described in this instruction and
must be installed under the wiring rules and regulations in the location where
it is installed. There are no user-serviceable parts inside the product.
Failure to follow these instructions can result in death or serious injury.
Equipment Damage Hazard
Install the device according to the instructions provided in this document.
Pay attention to the specifications and wiring diagrams related to the
installation. Do not use this product for any other purpose than specified in
this instruction. The product is suitable for indoor use only. Apply
IEC60898-1 compliant 250V~ 6A MCB as an overload protective device.
Environmental Protection
Electrical-rated loads and limits of a given product should NEVER be
exceeded at any time. The electricity supply should always be isolated at its
source (Distribution Board) before attempting any installation or maintenance.
FAQ
-
Q: Can I use this dimmer switch for outdoor use?
A: No, this product is suitable for indoor use only. -
Q: What is the maximum load supported by this dimmer switch?
A: The maximum load supported is 1000W. -
Q: How do I activate the dimming function?
A: The dimmer switch is activated by pressing the dimmer shaft only. The dimming function is controlled by rotating the dimmer shaft.
FEATURES
PDM010 DC 1-10V Dimmer
- Adjustable voltage: DC 1-10V
- Dimming range: 1-100%
- Silent & flicker-free
- Soft start feature
- Full short circuit protection
- In-built over-current protection
Operating Voltage (Ref. wiring diagram 2) | 240V ac ~ 50 Hz |
---|---|
Max Load (Ref. wiring diagram 2) | 1000W |
Dimming Technique | DC 1-10V |
Compliance | BS EN 60669-2-1 |
Load Symbol
|
Compatible Loads
|
Max Load
---|---|---
|
1-10V, Dimmable LED
|
1000W
ON OFF & DIMMING FUNCTION
Dimmer switch is activated by pressing the dimmer shaft only, dimming function by rotating the dimmer shaft only.
EXAMPLE WIRING DIAGRAM
DIAGRAM 1. EXAMPLE WIRING DIAGRAM 2.
WARNING
RISK OF ELECTRIC SHOCK
- Hazardous voltage and electrical current may be present at the wire leads of this product even when the device is switched off.
- Lock out and tag the input circuit before accessing the wiring connections.
- This device must be installed by a qualified and experienced electrician following applicable current electrical regulations.
- To comply with all safety standards, the product must be used only for the purpose described in this instruction and must be installed under the wiring rules and regulations in the location where it is installed.
- There are no user-serviceable parts inside the product.
Failure to follow these instructions can result in death or serious injury.
EQUIPMENT DAMAGE HAZARD
- Install the device according to instructions in this document.
- Pay attention to the specifications and wiring diagrams related to the installation.
- Do not use this product for any other purpose than specified in this instruction.
- The product is suitable for indoor use only.
- Apply IEC60898-1 compliant 250V~ 6A MCB as an overload protective device.
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
LEGAL DISCLAIMER
The installation of electrical products is inherently dangerous and can lead
to serious injury or death. The products we sell MUST be installed by a
qualified and experienced electrician following applicable current electrical
regulations. Any advice, guidance or other information provided by Enkin on
their website or within any of our publications cannot completely anticipate
your situation and common sense must prevail. Products need to be checked
before installation and regularly for damage and wear and tear. Products
should be returned and not used if in any doubt of their integrity. Electrical
rated loads and limits of a given product should NEVER be exceeded at any
time. The electricity supply should always be isolated at its source
(Distribution Board) before attempting any installation or maintenance. No
advice or information, whether oral or written, obtained by you from us or
through the service, our employees, consultants, and/or retailers shall create
any warranty not expressly made herein. You agree to assume all and any risk
resulting from the utilization of the information provided by Enkin. You also
expressly agree not to hold us responsible for any damage, personal injury,
death or loss resulting from your use of our information, service or
regulatory-compliant products.
Scan the QR Code for more detailed technical information on this product
www.enkin.com
Enkin is a trading name of Trade Ivy. Registered in England Number: 10809945.
Copyright © 2021 All Rights Reserved Trade Ivy Limited, Unit 3C Latham Park,
St Blazey Road, Par, PL24 2HY
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>