AMP45BACQ 45mm 50nm Electronic Tubular Motor Instruction Manual

AMP45BACQ Instruction Manual

Fields of Application

Specifications

Working temperature: -10º C ~ +65º C
Input Voltage: AC 120V,60Hz;

Model| Rated Torque
(N.m)| Rated Speed
(RPM)| Rated Power
(W)
---|---|---|---
AMP45BACQ-10/21| 10.0| 21| 118

Attention
Never drop, knock, drill or submerge the motor. Keep the power cable in the proper position as shown below.
Read all safety instructions before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

Safety Instructions

1. Do not expose motor to humid, damp, or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use.
6. Ensure the correct crown and drive adaptor are used.
7. Ensure the power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls should be property isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11. Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty.

Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.
Please scan QR code to see more AMP™ product information

http://ampmotorization.com/

Power Options – Wiring

*Licensed electrician required.
Cut off the main power supply.
Connect the motor according to the information in the table below.
Ensure cable is kept clear of fabric.
Ensure antenna is kept straight and away from metal objects.

P1 Button Instructions

1. Test Motor
2. Activate Pairing Mode
3. Sleep Mode
4. Reverse Direction
5. Reset To Factory Settings

Button Instructions

Essential Settings
The steps in factory mode must be completed to ensure proper operation.

Pair / Unpair Remote Control

a. Press “P1” button (about 2 sec) on the motor head until motor jog x1 and beep x1.
b. In the next 10 secs, press and hold “Stop” button on the remote control until motor jog x2 and beep x3.

• Repeat the same procedure to unpair remote control.

Change Motor Direction (if necessary)

Press “Up” or “Down” button to check if the shade moves in the desired direction.
If you need to reverse the direction, press and hold (about 2 sec) “Up” and “Down” buttons simultaneously until motor jog x1 and beep x1.

*The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch direction by pressing P1 button (See P1 button instructions).

Setting the Upper and Lower Limits

3.1 Set Upper Limit
a. Press “Up” button to raise the shade, then press “Stop” button when it is in the desired upper limit.
b. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

3.2 Set Lower Limit
a. Press “Down” button to lower the shade, then press “Stop” button when it is in the desired lower limit.
b. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

*If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits.

Adjust Limits

4.1 Adjust the Upper Limit
a. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x1 and beep x1.
b. Use “Up” button to raise the shade to the desired highest position, and use “Up” or “Down” button to do the final adjustment if necessary.
c. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

4.2 Adjust the Lower Limit
a. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x1 and beep x1.
b. Use “Down” button to lower the shade to the desired lowest position, and use “Up” or “Down” button to do the final adjustment if necessary.
c. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

Favorite Position

5.1 Set Favorite Position
a. Use “Up” or “Down” button to move the shade to desired Favorite position.
b. Press and hold (about 2 sec) one “P2” button on the back of remote control until motor jog x1 and beep x1.
c. Press and hold (about 2 sec) “Stop” button until motor jog x1 and beep x1.
d. Once more, press and hold (about 2 sec) “Stop” button until motor jog x2 and beep x3.

5.2 Send Shade to Favorite Position
Press and hold (about 2 sec) “Stop” button, motor will move to Favorite position.

5.3 Delete Favorite Position
a. Press and hold (about 2 sec) one “P2” button until motor jog and beep x1.
b. Press and hold (about 2 sec) “Stop” button until motor jog and beep x1.
c. Once more, press and hold (about 2 sec) “Stop” button until motor jog x1 and long beep x1.

Roller Mode and Sheer Mode

6.1 Roller Shade Mode – continue movement after a short press Default Mode
a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1.
b. Press and hold (about 2 sec) “Stop” button until motor jog x2 and beep x3.

6.2 Sheer Shade Mode – jog movement after a short press (continue movement after a long press)
a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1.
b. Press and hold (about 2 sec) “Stop” button until motor jog x1 and beep x1.

Add or Remove Additional Remote

7.1 Using Current Remote Control
a. On the current remote control, press and hold (about 2 sec) one “P2” button until motor jog x1 and beep x1.
b. Once more, on the current remote control, press and hold (about 2 sec) one “P2” button until motor jog x1 and beep x1.
c. On the New remote control, press and hold (about 2 sec) one “P2” button until motor jog x2 and beep x3.

7.2 New Remote Control
Follow instructions under the section 1.
Pair / Unpair Remote Control

Adjust Motor Speed

8.1 Acceleration Speed
a. Press one “P2” button until motor jog x1 and beep x1.
b. Press “Up” button until motor jog x1 and beep x1.
c. Once more, press “Up” button until motor jog x2 and beep x1.

8.2 Deceleration Speed
a. Press one “P2” button until motor jog x1 and beep x1.
b. Press “Down” button until motor jog x1 and beep x1.
c. Once more, press “Down” button until motor jog x2 and beep x1.
*If the motor has no response, it already has a Maximum or Minimum speed.

Declarations

U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This  equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence.

IC Radiation Exposure Statement:
The device is compliance with RF field strength limits, users can obtain Canadian information on RF exposure and compliance.
This Class B digital apparatus complies with Canadian ICES-003.
CAN ICES-003 (B)/NM

Quick Index

Stop (hold down for 2s)
Lower Limit:  Down (hold down for 2s)  >  Down + Stop (hold down for 2s)
4. Add / Remove Favorite Position| P2  >  Stop  >  Stop
 5. Roller Mode & Sheer Mode Switch| Up + Down (hold down for 5s)  >  Stop
6. Adjust Limits| Upper Limit:  Up + Stop (hold down for 5s)  >  Up or Down

  Up + Stop (hold down for 2s)
Lower Limit:  Down + Stop (hold down for 5s)  >  Up or Down  >  Down + Stop (hold down for 2s)
7. Pair / Unpair Additional Emitter| P2 (existing)  >  P2 (existing)  >  P2 (new)
8. Speed Regulation| Acceleration:  P2  >  Up  >  Up
Deceleration:  P2  >  Down  >  Down

Troubleshooting

power cable connection and AC plug
Remote control battery is discharged| Replace battery
Battery is inserted incorrectly into remote control| Check battery polarity
Radio interference / shielding| Ensure remote control and the antenna on the motor are positioned away from metal objects
Receiver is far away from Remote
Control| Move remote control to a closer position
Power failure| Check power supply to motor is connected and active
 Incorrect wiring| Check that wiring is connected correctly
 Cannot program a single motor
(multiple motors respond)| Multiple motors are paired to the same channel.| Always reserve an individual channel for programming functions
SYSTEM BEST PRACTICE – Provide an extra 15 channel  remote in your multi-motor projects that provides individual control for each motor for programming purposes
Place all other motors into sleep mode (ref to P1 button instructions)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>