legrand WNRL34 Radiant Wireless Dimmer Switch User Manual

legrand WNRL34 Radiant Wireless Dimmer Switch

Specifications

• Minimum distance between transmitter’s radiating structure(s)  and the user or nearby persons: 90 mm
• Manufacturer: Legrand
• Warranty: Void if there are any unauthorized changes or modifications to the device

Product Usage Instructions

Before You Start

1. Turn off the power to the device at the circuit breaker. Make sure power is off to all devices in the electrical box.
2. If applicable, remove the existing device.

Installation
Break off tabs for multi-gang installation:

1. Install the switch by following the manufacturer’s instructions.

Getting to Know Your Switch

bottom of the paddle to turn the light off.
LED Indicator| Indicates the current state of the device. Refer to LED Locator
Light Explanations for detail.
EZ Button| Used to enter setup mode.

setup
To reset the device to factory defaults:

1. Delete the device from the app.
2. Press and hold the EZ button for 10 seconds until you see the LED blink red, then release.
3. The LED will change to solid red when the reset is complete.

LED Light Explanations

BEFORE YOU START

Review this guide in its entirety. Consult an electrician with any questions or if you are unsure of your abilities.

• Warning: Incorrect installation could result in death, serious injury, and/or damage to your home or devices.
• CAUTION: To reduce the risk of injury and/or overheating and damage to other equipment:
  • Do not install to control a receptacle or a motor-controlled appliance.
  • For dry, indoor use only.
  • Do not use it to power medical equipment.
  • Connect the smart Switch to a 120 VAC, 60 Hz power source ONLY.
  • Always use copper wire to install the smart Switch & follow all applicable local & national electrical codes.

WHAT YOU NEED

Required:

• Phillips-head screwdriver
• Flat blade screwdriver

You May Also Need:
Voltage tester, pliers, wire cutter, wire stripper, electrical tape, flashlight, wiring leads (included), and wire nuts (included).

INSTALLATION

1. Turn Off Power To Device At Circuit Breaker NOTE: Ensure power is off to all devices in electrical box.
2. Remove Existing Device (if applicable)

Check for the following wires:

• a. HOT or LINE : Receives power from the circuit box. Referred to as “hot” for the purpose of this guide. Do not touch or let “hot” wire contact
  other wires.

• b. NEUTRAL: Creates a path to return current to the power source when the device is off. Required for your Switch installation.

• c. GROUND: Provides a safe path for electricity in the event of a short circuit.

Wire Smart Switch

• a. Connect the WHITE neutral wire in the box to the Neutral terminal marked “WHITE” using #12 or #14 AWG wire stranded or solid copper conductors. Strip the wire to the length shown on the back of the product. Torque to 14-16 lbs-in.
• b. Connect the BLACK Hotwire in the box to the Hot terminal marked “HOT” using #12 or #14 AWG wire stranded or solid copper conductors. Strip the wire to the length shown on the back of the product. Torque to 14-16 lbf-in.
• c. Connect the GREEN ground wire on the Switch to the ground wire(s)
  in the box with the wire nut provided.

Secure Smart Switch

• a. Fold wires into the electrical box, taking care not to pinch a wire.
• b. Use included screws to secure the smart Switch to electrical box.
• c. Snap on the radiant wall plate.
• d. If installing in the multi-gang application, break off the tab at the top and bottom of the strap.

SETUP

This device is designed to work with a radiant® Smart Gateway with Netatmo. Follow the instructions from your app to finish setting up your Switch.

Set UP Your System

• a. Download and launch the Legrand Home + Control app. The app is available on the App Store or Google Play.
• b. Connect your smart device to your home network by following the step-by-step instructions in the app.
• c. Use the app to control your smart device.

For the most recent instruction sheets or more information on this product, please see this link ovscan the QR code: https://www.legrand.us/p/WNRL34wh

GETTING TO KNOW YOUR Switch

bottom of the paddle to turn the light off.
2| LED Indicator| Indicates the current state of the device. Refer to “LED Locator Light Explanations” for details.
3| EZ Button| Used to enter setup mode

Reset To Factory Default Deleting a device from the app will reset it to factory defaults. To manually reset the device to factory defaults press and hold the EZ button for 10 seconds until you see the LED blink red then release. The LED will change to solid red when the reset is complete.

LED Light Explanations

Legrand reserves the right to change specifications without notice

FCC

REGULATORY INFORMATION
FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 90 mm between the transmitter’s radiating structure(s) and the body of the user or nearby persons. NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment.

Contains FCC ID: 2AU5D-WNZED

IC NOTICE: This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the minimum separation distance of 90 mm to the human body. Note: Any changes or modifications to this device that are not expressly approved by the manufacturer, will void the warranty and the user’s authority to operate the equipment.

• IC: 25764-WNZED
• HVIN: WNRL34

Catalog Number(s)
Country of Origin: Made in China

CLEANING INSTRUCTIONS

To properly maintain both the appearance and performance of a Legrand switch, dimmer, or outlet, please use only mild soap or detergent on a damp cloth to clean the device and wall plate. These care instructions should be applied to all electrical wiring devices, including the designer switches and outlets from the adorne® and radiant® Collections. Approved soaps/detergents: Dawn Ultra Antibacterial Dishwashing Liquid (full concentration); Ajax Ultra Dish Liquid (full concentration); Ivory Dish Soap (full concentration); Gain Ultra Clean Dishwashing Liquid (full concentration); and Ultra Palmolive Antibacterial. The use of any spray, mister, or aerosol agent is strongly discouraged, as is the use of disinfecting chemicals* or harsh detergents. These cleaning solutions can damage and degrade the device’s plastic casing and are not recommended for use.

Please note the following article of the National Electrical Code (NEC) concerning the use of deteriorating agents on electrical products.
Article 110.11. Unless identified for use in the operating environment, no conductors or equipment shall be located in damp or wet locations; where exposed to gases, fumes, vapors, liquids, or other agents that have a deteriorating effect on the conductors or equipment; or where exposed to excessive temperatures.

• FPN No. 1: See 300.6 for protection against corrosion.
• FPN No. 2 : Some cleaning and lubricating compounds can cause severe deterioration of many plastic materials used for insulating and structural applications in equipment.

LIMITED ONE-YEAR WARRANTY

Legrand will remedy any defect in workmanship or material in Legrand products which may develop under proper and normal use within ONE year from the date of purchase by a consumer: (1) by repair or replacement, or, at Legrand’s option, (2) by return of an amount equal to consumer’s purchase price. Such remedy is instead of ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Such remedy by Legrand does not include or cover the cost of labor for removal or reinstallation of the product. ALL OTHER FURTHER ELEMENTS OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED HEREBY. (Some states do not allow disclaimers or exclusion or limitation of incidental or consequential damages, so the above disclaimer and limitation or exclusion may not apply to you.) ANY IMPLIED WARRANTIES INCLUDING WHERE REQUIRED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE ONE YEAR SET FORTH ABOVE. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.) To ensure safety, all repairs to Legrand products must be made by Legrand, or under its specific direction. The procedure to obtain performance of any warranty obligation is as follows: (1) Contact Legrand, Syracuse, New York 13221, for instructions concerning return or repair; (2) return the product to Legrand, postage paid, with your name and address and a written description of the installation or use of the Legrand product, and the observed defects or failure to operate, or other claimed basis for dissatisfaction. This warranty gives you specific legal rights and you may also have other rights which vary from state to state

FAQ

• Q: What is the minimum distance required between the transmitter’s radiating structure(s) and the user or nearby  persons?
  

  • A: The minimum distance required is 90 mm.

• Q: What will void the warranty?
  

  • A: Any unauthorized changes or modifications to the device will void the warranty.

• Q: How do I reset the device to factory defaults?
  

  • A: Delete the device from the app and press and hold the EZ button for 10 seconds until you see the LED blink red, then  release. The LED will change to solid red when the reset is complete.

• Q: What does a blinking green LED light indicate?
  

  • A: A blinking green LED light indicates that the device is attempting to connect to the network.

For covering patents, see www.legrand.us/patents

No: 341406 1/24
© Copyright 2024 Legrand All Rights Reserved.

Questions? We’re here to help.
Phone: 1-877-833-3303 8:00 a.m. to 8:00 p.m. EST (M-F)
Email: smartlighting@legrand.us
Chat: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the chat icon to open a dialogue box)

800.223.4185 1.877.BY.LEGRAND
www.legrand.us
www.legrand.ca

References

• Patents | Legrand
• Legrand CA | Delivering and Managing Power, Light, and Data
• Legrand US | Delivering and Managing Power, Light, and Data
• Patents | Legrand
• Server Error Page
• Smart Lighting from the radiant Collection ⎸Legrand

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>