P I T E-PSR18-D3-A1 Cordless Drill Instruction Manual

OPERATION MANUAL
E-PSR18-D3-A1

E-PSR18-D3-A1 Cordless Drill

CORDLESS DRILL

Please read the instruction manual carefully before use!

Safety Notes

General power tool safety warnings
WARNING Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.

Work area safety
► Keep work area clean and well lit. Cluttered or dark areas invite accidents.
► Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
► Keep children and bystanders away while operating a power tool. Distrac- tions can cause you to lose control.

Electrical safety
► Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
► Avoid body contact with earthed or grounded surfaces, such as pipes, radi- ators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
► Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
► Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the risk of electric shock.
► When operating a power tool outdoors, use an extension cord suitable for out- door use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
► If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

► Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury.
► Use personal protective equipment.
Always wear eye protection. Protective equipment such as dust mask, nonskid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
► Prevent unintentional starting. Ensure the switch is in the off -position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
► Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
► Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
► Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
► If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

Power tool use and care
► Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was designed.
► Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
► Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
► Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
► Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly  maintained power tools.
► Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
► Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Battery tool use and care
► Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fi re when used with another battery pack.
► Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
► When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
► Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

Service
► Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Safety warnings for drills and screwdrivers
► Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
► Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory or fastener may contact hidden wiring. Cutting accessory and fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
► Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
► Use appropriate detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line causes property damage.
► Switch off the power tool immediately when the tool is jams. Be prepared for high reaction torque that can cause kickback.
► Hold the machine with a fi rm grip. High reaction torque can briefly occur while driving in and loosening screws.
► Secure the workpiece. A workpiece  clamped with clamping devices or in a vice is held more secure than by hand.
► Always wait until the machine has come to a complete stop before placing it down. The tool insert can jam and lead to loss of control over the power tool.
► Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against continuous intense sunlight, fi re, water, and moisture. Danger of explosion.
► In case of damage and improper use of the battery, vapours may be emitted. Ventilate the area and seek medical help in case of complaints. The vapours can irritate the respiratory system.
► Use the battery only in conjunction with your P.I.T. power tool. This measure alone protects the battery against dangerous overload.
► The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit can occur and the battery can burn, smoke, explode or overheat.
► The battery is supplied partially charged. To ensure full battery capacity, completely charge the battery in the battery charger before using for the first time.
► Read the operating instructions of the battery charger.
► Adjust the gear switch only when the machine is at a complete stop.
► Always push the gear selector and turn the operating mode selector switch through to the stop. Otherwise, the machine can become damaged.

Product Description and Specifications
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious injury.
Intended use
The machine is intended for driving in and loosening screws as well as for drilling in wood, metal, ceramics and plastic. GSB machines are additionally intended for impact drilling in bricks, brickwork and masonry.
The light of this power tool is intended to illuminate the power tool’s direct area of working operation and is not suitable for household room illumination.

Technical Data

Note
In text and numbers, may technical errors and mistakes be made chat rooms. As the product is constantly being improved, P.I.T. reservesthe right to make changes to the specifications and equipment of the product specified here without prior notice.
Product features
The numbering of the product features refers to the illustration of the machine on the graphics page.

1. Tool holder
2. Keyless chuck
3. Torque presetting ring
4. Gear selector
5. Battery pack
6. Battery unlocking button
7. Worklight
8. Rotational direction switch
9. On/Off switch
10. Handle (insulated gripping surface)

Contents of delivery
Cordless drill ……………………….1 pc
Lithium Battery…………….1 pc
Charger………………………….. 1 pc
Screwdriver bits…………….. 3 set
Adapter…………………………………. 1 pc
Instruction manual ……………….1 pc
13pcs Hss Hex Shank Drill Bit Set ………………..1 set

Assembly

Battery Charging
Note: The battery supplied is partially charged. To ensure full capacity of the battery, completely charge the battery in the battery charger before using your power tool for the first time.
The lithium ion battery can be charged at any time without reducing its service life. Interrupting the charging procedure does not damage the battery.
The lithium-ion battery is protected against deep discharge by the “Electronic Cell Protection (ECP)” system. The protective circuit switches off the power tool when the battery is discharged – the working tool stops.
► Do not continue to press the On/Off switch after the machine has been automatically switched off. The battery can be damaged.
Removing the battery
The battery is equipped with two locking levels that should prevent the battery from falling out when pushing the battery unlocking button unintentionally. As long as the battery is inserted in the power tool, it is held in position by means of a spring. To remove the battery, press the unlocking button and pull out the battery toward the front. Do not exert any force.
Changing the Tool (see fi gure A)
► Before any work on the machine itself (e. g. maintenance, tool change, etc.) as well as during transport and storage, remove the battery from the power tool. There is danger of injury when unintentionally actuating the On/Off switch.
Open the keyless chuck by turning in rotation direction , until the tool can be inserted. Insert the tool.
Firmly tighten the collar of the keyless chuck 2 by hand in rotation direction . This auto- matically locks the drill chuck.
Dust/Chip Extraction
► Dust from materials such as lead-containing coatings, some wood types, minerals and metal can be harmful to one’s health and cause allergic reactions, lead to respiratory infections and/ or cancer. Materials containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 fi lter-class respirator. Observe the relevant regulations in your country for the materials to be worked.
► Prevent dust accumulation at the workplace. Dust can easily ignite.

Operation

Starting Operation
Inserting the battery
Note: Use of batteries not suitable for the machine can lead to malfunctions of or cause damage to the power tool.
Set the rotational direction switch to the center position in order to avoid unintentional starting.
Insert the charged battery into the handle so that it can be felt to engage and faces fl ush against the handle.
Reversing the rotational direction (see figure B)
The rotational direction switch is used to reverse the rotational direction of the machine. However, this is not possible with the On/Off switch actuated.
Rotate clockwise: Move the rotational direction switch on both sides up to the stop into position .
Rotate anticlockwise: Move the rotational direction switch on both sides up to the stop into position .
Setting the operating mode
Drilling
Set the operating mode selector switch to the “drilling” symbol.

Screwdriving
Set the torque selector setting ring to the “screwdriving” symbol.
Switching On and Off
To start the machine, press the On/Off switch and keep it pressed.
The LED lights up when the On/Off switch is halfway or fully pressed, and enables illumination of the screwing location in unfavorable light conditions.
Adjusting the Speed
The speed of the switched-on power tool can be variably adjusted, depending on how far the On/Off switch is pressed.
Light pressure on the On/Off switch results in a low rotational speed. Further pressure on the switch results in an increase in speed.
Setting the torque
With the torque preselection ring , the required torque can be preselected in 17 steps.
The inserted tool is stopped as soon as the set torque is reached.
Gear selection, mechanical
► The gear selector can be actuated at standstill or when the machine is running. However, this should not be done while operating at full load or maximum speed.
Low speed range; for working with large drilling diameters.
High speed range; for drilling with small drilling diameter.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be subject to overload. When the load is too high or the allowable battery temperature range is exceeded, the speed is reduced.
The power tool will not run at full speed until reaching the allowable battery temperature.
Protection Against Deep Discharging
The lithium-ion battery is protected against deep discharging. When the battery is empty, the machine is switched off by means of a protective circuit: The inserted tool no longer rotates.
Rapid Shut-off
The rapid shut-off feature enables better control of the power tool. The power tool shuts off in case of sudden and unexpected rotation of the power tool around the drilling axis. The rapid shut-off feature is indicated by a fl ashing LED on the power tool.
To restart the machine, release the On/Off switch and then actuate again.
► Rapid shut-off can trigger only when the power tool is running at maximum operating speed and can rotate freely around the drill bit axis. Choose a suitable work position for this.
Otherwise, rapid shut-off will not be ensured.
Working Advice
► Apply the power tool to the screw only when it is switched off . Rotating tool inserts can slip off.
An auxiliary tool can be used to remove the screwdriver bit or universal bit holder. Maintenance and Service
Maintenance and Cleaning
► Before any work on the machine itself (e. g. maintenance, tool change, etc.) as well as during transport and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating the On/Off switch.
► For safe and proper working, always keep the machine and ventilation slots clean.
When the battery is no longer operative, please refer to an authorized after- sales service agent for P.I.T. power tools.
Dispose of waste
** Damaged power tools, batteries, accessories and waste packaging materials must be recycled and reused in an environmentally friendly manner.
Do not throw power tools and accumulators / batteries into general household waste!
Product serial number interpretation serial number The date of manufacture of the product is encoded in the serial number printed on the body of the tool. The fi rst 2 digits indicate the year of issue, the next 2 digits indicate the month.
TERMS OF WARRANTY SERVICE
To customers (users) of warranty service:**

1. This warranty certificate is the only document that confi rms your right to free warranty service. If this proof is not presented, no claims will be accepted. Warranty certifi cates cannot be recovered if lost or damaged.
2. It is required to provide a valid and legal document for purchasing the product. The document must have the name or seal of the sales company; at the same time, state the full model name of the purchased P.I.T. product, the serial number on the nameplate of the fuselage, and the date of purchase, and the required warranty. The whole machine and its accessories.

The warranty period:

1. The warranty period of the product is 12  months from the date of sale. During the warranty period, the service department will eliminate manufacturing defects free of charge and replace the parts that fail due to the manufacturer’s fault. In warranty repair, an equivalent operable product is not provided. Replaceable parts become the property of the service provider.
2. The wear degree on the diameter of the motor rotor commutator is less than 0.4 mm (except for brushless motor tools), and the internal damage caused by the quality of the tool belongs to the warranty.

The following situations occur during the warranty period, which is not covered by the warranty:

1. In the absence of any valid legal documents (invoices) such as warranty certificates and warranty cards to prove the date of purchase.
2. Damage caused by natural wear and overload. (For example, motor rotor and stator failure caused by overload, scorching or melting of the primary winding of the welding machine transformer, charging or starting the charging device, melting of internal parts, burning of electronic circuit boards, etc.)
3. The casing and power cord are mechanically damaged, as well as damage caused by corrosive media and high and low temperature, foreign objects entering the ventilation network of the motor, and damage caused by improper storage (corrosion of metal parts);
4. Damage caused by improper carrying, transportation and storage by users.
5. Products that are opened, repaired, replaced or modified by users themselves.
6. Any damage caused by indiscriminate use, beyond the scope of use of the tool, and not in accordance with the instructions for use and maintenance. (see chapter “Safety Pre- cautions” in the manual);
7. The damage caused by the following situations is not guaranteed due to improper use and non-quality problems:
8. When the power tool is running at high speed, use the braking device to forcibly stop the rotation.
9. Excessive pressure is applied to the tool during the use of the tool.
10. Use the tool outside the scope of its purpose and capabilities.
11. Damage caused by the tool working in a dusty environment for a long time without timely maintenance of the tool.
12. Change the rotation direction of the work head before the tool stops completely.
13. Shock the battery or charger and replace the plug of the charger without permission, causing damage to the battery or charger.
14. Damage caused by two-stroke gasoline tools not being fueled in the correct proportions.

The warranty does not include:

1. Replacement of accessories (accessories and components) such as batteries, discs, blades, drills, drills, chucks, chains, sprockets, collet clamps, guide rails, tension and fastening elements, dresser heads, grinders And belt sander base machine, hexagonal head, etc.;
2. Wearing parts, such as: carbon brushes, transmission belts, seals, protective covers, guide rollers, guide rails, rubber seals, bearings, toothed belts and wheels, shanks, brake belts, starter ratchets and ropes, piston rings Wait. The above accessories are replaced with paid services during the warranty period;

Hangzhou Gongxuan Science & Technology Co., Ltd
Address: Room 2-1504, Jiabao Scientific Innovation Center, 519 No. 2 Road,
Baiyang Street, Qiantang District, Hangzhou City, Zhejiang Province, China
E-mail: online@pit-tools.com
Made in Chinahttp://www.pit-tools.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>