T I P TSS1600K Mud Dry Vacuum Cleaner Instruction Manual

: June 1, 2024
: T I P

Table of Contents

TSS1600K Mud Dry Vacuum Cleaner
General safety information
Range of use
Technical Data
Commissioning
Maintenance
Warranty
How to order spare parts
Documents / Resources

TSS1600K Mud Dry
Vacuum Cleaner
Instruction Manual

TSS1600K Mud Dry Vacuum Cleaner

EC declaration of conformity
We, T.I.P. Technische Industrie Produkte GmbH, Siemensstr.
17, D-74915 Waibstadt, declare in our sole responsibility that the products identified below comply with the basic requirements imposed by the EU directives specified below including all subsequent amendments: 2006/42/EC, 2014/30/EU, 2011/65/EU.
Art.: Schlamm-Trocken-Sauger mud-dry vacuum cleaner TSS 1600 K
applied standards/ angewendete Normen:
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 61000-3-2:2019+A1:2021
EN 61000-3-3:2013+A1:2019+A2:2021
EN 60335-1:2012+A11:2014+A13:2017+A1:2019+A14:2019+A2:2019+A15:2021
EN 60335-2-2:2010+A11:2012+A1:2013
EN 62233:2008
EN IEC 63000:2018
AfPS GS 2019:01 PAK
Documentation Representative:
Dear customer,
Congratulation for buying your new device from T.I.P.!
Like all our products, this one, too, was developed using the latest technological knowledge. The device was manufactured and assembled on the basis of state-of-the-art technology using most reliable electrical or electronic components which ensure a high level of quality and a long life of your new product.
Please read through these operating instructions carefully to make sure that you can fully benefit from all features.
Some explanatory illustrations can be found at the end of these operating instructions.
We hope you will enjoy your new device!

General safety information

Please read through these operating instructions carefully and make yourself conversant with the control elements and the proper use of this product. We shall not be liable in the case of damage caused as a result of the non- observance of instructions and provisions of the present operating instructions. Any damage caused as a result of the non-observance of the instructions and regulations contained in the present operating instructions shall not be covered by the warranty terms. Please keep these operating instructions in a safe place and hand them on together with the device should you ever dispose of it.
Persons not familiar with the contents of these manual may not use this device.
The appliance must not be used by children.
The appliance may be used by persons with reduced physical, sensory or mental capabilities or lack of experience and / or knowledge if they have been supervised or instructed in the safe use of the equipment and have understood the resulting hazards. Children are not allowed to play with the device. Keep the appliance and its cord out of reach of children. Cleaning and user maintenance shall not be made by children without supervision.
The appliance must not be used when people are in the water.
The appliance must be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Notes and instructions with the following symbols require particular attention:
Any non-observance of these instructions involves the danger of bodily harm to people and/or damage to property.
Any non-observance of this instruction bears the risk of an electrical shock which may cause damage to persons or property.
Please inspect the device for damage occurred during transportation. In case of damage, the retailer has to be informed immediately, at the latest within 8 days after the date of purchase.
In addition to the basic safety precautions for avoiding accidents, please note the following:

CAUTION: Before performing any installation or maintenance work, disconnect the electrical equipment from the power source by unplugging the power cord from the electrical outlet. The appliance must not be operated if persons are in the water. Switch off the main fuse of the household electricity supply before pulling out the mains cable if the connector or the mains socket is wet. Never transport or hang up the unit on the mains supply line.
Make sure that the voltage indicated on the type plate of the appliance matches the mains voltage.
Before connecting the unit to the power supply, ensure that the power cord and the unit are not damaged in any way.
A corresponding residual current circuit breaker (RCD) with a rated fault current of max. 30 mA. Please contact a qualified electrician.

Packing parts can be dangerous (for example plastic bags) – therefore unachievable for children, for persons who are unaware of their actions or for animals.
Only use accessories which are included in the scope of delivery or only those specified in the operating instructions. Use of unauthorized accessories may affect safety.
Any use of the device, which is not described in this manual, can be dangerous and must therefore be avoided.
Before draining the container manually, turn the unit off and unplug the appliance from the wall outlet.
When the appliance is operating, be careful not to hold the suction nozzle on a sensitive body (such as the eyes, mouth or ears).
Children should be supervised so that they do not play with electrical appliances.
Before use, the unit must be assembled correctly with all parts. Check that the power outlet and the plug are matched.
Never touch the mains plug with wet hands.
The max. System impedance of electrical supply systems for connecting devices with a 1600 watt motor is Zmax = 0.12 + j0.08. If necessary, please inquire with your responsible utility for the existing system impedances.
Switch off the appliance and unplug the mains plug before servicing, cleaning, changing the filter and after use. Do not leave the appliance unattended; do not leave it in the reach of children or persons who are unaware of their actions.
In the case of incidents (for example contact with detergents or chemicals), clean the machine with plenty of clear water. In the event of a fault, always pull the mains plug to avoid danger.
Never leave the appliance unattended during operation.
Do not immerse the appliance in water or clean it with a water jet.
Make sure that the power cord, the housing or other parts of the appliance are damaged. If so, do not use the device and make repair at the customer service.
If you use extension cables, make sure that they are suitable for the appropriate application and those they are on a dry surface and are protected against splashing water.
Service and repairs may only be carried out by qualified personnel. Defective parts of the device may only be replaced with original parts.
The manufacturer is not responsible for any damage to persons or objects caused by improper use of the appliance or by ignoring the instructions given in this manual.

1.1. Special safety instructions for the pond cleaner

If the appliance falls over during operation, immediately switch off the appliance, unplug and then install the appliance.
Always place your appliance in a suitable location. The device must not be placed on brackets, pedestals or similar supports, but on a level and firm surface.
Never use the appliance to draw water from containers, sinks, etc. Do not absorb solid substances and under any circumstances easily inflammable (eg ash or soot from the fireplace), explosive, toxic or harmful substances.
Before use, check the mobility of the float inside the sponge filter inside the pond sludge filter.
Immediately turn the appliance off and unplug if liquid or foam escapes. Never use the unit without the sponge filter.
The appliance must not be used for pond emptying.
When installing the appliance, keep a safety distance of 2 m from the pond. The appliance must not be used when people are in the water. Avoid working with the unit during rain.
Do not move the unit by pulling it on the hose.
The garden ponds must be laid out in accordance with international and national regulations and regulations.

Range of use

This product is intended for private use in the home area and not for commercial or industrial purposes.
Use the appliance only for cleaning and removing foliage and mud in ponds.
The appliance is not suited to discharge saltwater, faeces, inflammable, etching, explosive or other hazardous liquids. Please observe the max. and min. temperatures of the liquids to be discharged stated in the technical data.

Technical Data

Model	TSS 1600 K
Mains voltage / frequency	220 – 240 V- / 50 Hz
Nominal performance	1,600 W
Connection cable	4 m / HO5VV-F
Suction height max.	1.8 m
Tank size	30 liters
Suction hose	4 m (0 35 mm)
Drain hose	1.5 m (0 35 mm)
Temperature medium max.	35 °C
Noise level guaranteed	85 dB
Weight (net)	7.6 kg
Article No.	30519

Scope of delivery
T.I.P. pond cleaner, suction hose, 4 suction pipes, suction sludge nozzle, closure cap, suction filter, drain hose, filter for waste water, feet’s, instruction manual.

Commissioning

Possible operating conditions:
MAN: Continuous operation (NOTE: please consider 30 sec than shut off the motor to empty the tank).
(0) OFF: The machine is switched off
AUTO: Automatic suction and emptying mode. After a working interval of approx. 30 seconds, the pond sludge suction device switches off for approx. 30 seconds.

Check that the switch is set to (0) OFF. It is recommended to connect the device to a circuit with a residual current circuit breaker with a rated fault current of max. 30 mA.

Assembly

Place the feet’s under the unit.
Attach the discharge hose to the discharge opening of the collecting container by using the hose end in which the already installed check valve is located.
Place the outlet filter over the other end of the drain hose and secure it with the cord. Secure the cord with the cord stopper.
Insert the suction hose into the opening of the suction nozzle.
As required, plug the extension tubes together (up to 4 pieces, the transparent one serves for the visual inspection of the water flow) and connect them to the suction hose.
Insert the pond sludge nozzle onto the last extension pipe.
• Ensure that the drain hose is placed so that the discharged sludge water is transported to the desired disposal location (for example, a collection container or drainage shaft). The drain hose must not be laid ascending.
The outlet filter is usually installed at the end of the hose in order to retain coarse dirt particles.
• Never use the appliance without the sponge filter installed.
• Insert the suction tube so deep into the body of the water until you touch the bottom with the pond sludge nozzle.
• Switch the switch to AUTO to switch the unit on.
• After a working interval of approx. 30 seconds, the pond sludge suction device switches off for approx. 30 seconds to empty the filled collecting container automatically. With this time interval, the device now operates continuously.
• When the maximum water level in the collecting vessel is reached, the float in the interior of the headboard stops the suction and the emptying process begins.
• The entire suctioned waste water is discharged via the discharge hose. Coarse dirt particles are collected by the outlet filter, if fitted.
• Clean the outlet filter from time to time during work or at the latest after finishing your work.
• If you want to stop or interrupt your work, set the switch to position (0) OFF. Always pull the plug out of the socket when the appliance is not in use.
• The device can also be used to suck up liquids in the receiver without drain hose. For this purpose, the drain opening of the container must be closed with the closure cap. For the suction process, set the switch to MAN (continuous operation). Note that there is no automatic emptying function in this operating position of the nipple, that is. The container must then be emptied manually.

Maintenance

CAUTION: Disconnect the electrical appliance from the power source before carrying out any maintenance work by pulling the plug out of the socket.
Do not use aggressive solvents or cleaning agents.

Remove the entire dirt and water from the interior of the collecting container.
Periodically clean the filter. The cleaning intervals depend on the degree of polluted water.
Make sure that the outlet filter does not obstruct the water drainage.
Check whether the float is free to move and clean it if necessary.

Warranty

The present device was manufactured and inspected according to the latest methods. The seller warrants for faultless material and workmanship in accordance with the legal regulations of the country in which the device was purchased. The warranty period begins with the day of the purchase and is subject to the provisions below:
Within the period of warranty, all defects which are to be attributable to defective materials or manufacturing will be eliminated free of charge. Any complaints are to be reported immediately upon their detection.
The warranty claim becomes void in the case of interventions undertaken by the purchaser or by third parties.
Damage resulting from improper handling or operation, incorrect setting-up or storage, inappropriate connection or installation or Acts of God or other external influences are excluded from warranty.
Parts being subject to wear and tear, are excluded from warranty.
All parts were manufactured using maximum care and high-quality materials and are designed for a long lifecycle.
It should be understood, however, that the wear and tear depends on the kind of use, the intensity of use and the internals of maintenance. Complying with the installation and maintenance information contained in the present operating instructions will therefore considerably contribute to a long lifecycle of these wearing parts.
In case of complaints, we reserve the option of repairing or replacing the defective parts or replace the entire device. Replaced parts will pass into our property.
Claims for liquidated damages are excluded unless they are caused by wilful acts or negligence on the side of the manufacturer.
The warranty does not provide for any claims beyond those referred to above. The warranty claim has to be evidenced by the purchaser in the form of the submission of the sales receipt. The present warranty commitment is valid in the country in which the device was purchased.
Please note:

Should your device fail to function properly, please verify first whether an operating error or another cause is present which cannot be attributed to a defect of the device.
In case you have to take or send in your defective device for repair, please be sure to enclose the following documents:
− Sales receipt (sales slip).
− A description of the occurring defect (a description as accurate as possible will expedite the repair work).
In case you have to take or send in your defective device for repair, please remove any attached parts which do not belong to the original condition of the device. If any attached parts of this kind should be missing upon the return of the device, we shall not be liable for them.

How to order spare parts

The fastest, most simple and cheapest way of ordering spare parts is through the internet. On our website www.tip-pumpen.de you will find a convenient spare part shop where you can order spare parts with just a couple of clicks. In addition, this is also the place where we publish comprehensive information and valuable tips on our products and accessories, introduce new devices and present current trends and innovations in the range of pump technology.
Service
In the case of warranty claims or malfunction, please contact your point of sale.
A current operating manual is available as required as a PDF file via e-mail: service@tip-pumpen.de
For EC countries only
** Do not throw electric appliances in your dustbin!
According to EU guideline 2012/19/EU concerning old electric and electronic appliances and its implementation in national law, such appliances must be collected separately and fed into an environment-friendly recycling system. Please consult your local waste management system for advice on recycling.
Annex: Illustrations
TSS 1600 K Functional parts / Details**

1 Upper part complete
2 Handle complete
3 Clip complete
4 Switch knob comipete
30 Suction connection plate
31 Suction connection
32 Tank
33 Barrel feet
34 Screw
35 Screw
36 Gasket ring for drain port
37 Drain port cover
38 Tube
39 Hose
40 Drain hose
41 Filter foam
notes
Lieber T.I.P. Kunde,

SERVICE-HOTLINE
+49 (0) 7263 9125-0
Montag bis Freitag von 08.00 bis 17.00 Uhr
Email: service@tip-pumpen.de
TECHNIKER-SPRECHSTUNDE
+49 (0) 7263 9125-50
Montag bis Freitag von 15.00 bis 17.00 Uhr
T.I.P. Technische Industrie Produkte GmbH
Siemensstraße 17
D-74915 Waibstadt / Germany
Tel.: +49 (0) 7263 9125-0
Fax: +49 (0) 7263 9125-85
Webseite: http://www.tip-pumpen.de https://tip-pumpen.de/etichettatura- ambientale/

Documents / Resources

| T I P TSS1600K Mud Dry Vacuum Cleaner [pdf] Instruction Manual
TSS1600K Mud Dry Vacuum Cleaner, Mud Dry Vacuum Cleaner, Dry Vacuum Cleaner, Vacuum Cleaner, Cleaner
---|---