LINDY 43382 USB 3.2 Gen 2×2 Dual M.2 NVMe SSD Enclosure User Manual

June 16, 2024
LINDY

LINDY 43382 USB 3.2 Gen 2×2 Dual M.2 NVMe SSD Enclosure

Safety Instructions

WARNING !
Please read the following safety information carefully and always keep this document with the product. Failure to follow these precautions can result in serious injuries or death from electric shock, fire or damage to the product. Touching the internal components or a damaged cable may cause electric shock, which may result in death. This device is a switching type power supply and can work with supply voltages in the range 100 – 240 VAC For worldwide usability four different AC adapters are enclosed: Euro type, UK type, US/Japan type and Australia/New Zealand type. Use the appropriate AC adapter as shown in the picture and ensure it is firmly secured in place and does not detach by pulling before installing into a power socket.

To reduce risk of fire, electric shocks or damage

  • Do not open the product nor its power supply. There are no user serviceable parts inside.
  • Only qualified servicing personnel may carry out any repairs or maintenance.
  • Never use damaged cables.
  • Do not expose the product to water or places of moisture.
  • Do not use this product outdoors it is intended for indoor use only.
  • Do not place the product near direct heat sources. Always place it in a well-ventilated place.
  • Do not place heavy items on the product or the cables.
  • Please ensure any adapters are firmly secured and locked in place before inserting into a wall socket

Instructions for Use of Power Supply

Attach the required country adapter to the plug
Place the country adapter on the power supply unit so that the 2 lugs on the lower end of the adapter fit into the corresponding recesses on the power supply unit. Then slide the adapter down until it clicks into
place. To remove, push the button and slide the adapter upwards.

Introduction

Thank you for purchasing the USB 3.2 Gen 2×2 Dual M.2 NVMe SSD Enclosure. This product has been designed to provide trouble free, reliable operation. It benefits from both a LINDY 2 year warranty and free lifetime technical support. To ensure correct use, please read this manual carefully and retain it for future reference. The Lindy USB 3.2 Gen 2×2 Dual M.2 NVMe SSD Enclosure allows the user to install two PCIe/NVMe based M.2 SSDs as an external drive to USB hosts like laptops or PCs.

The additional Clone feature enables duplicating M.2 NVMe SSDs – even without connection to a computer (“offline cloning”). Support for the USB 3.2 Gen 2×2 standard guarantees SuperSpeed 20Gbps data transfer rates. UASP support also ensures faster speeds for UASP enabled computers.

Package Contents

  • USB 3.2 Gen 2×2 Dual M.2 NVMe SSD Enclosure
  • 0.25m USB 3.2 Gen 2×2 Type C to C cable
  • Multi-Country Power Supply 12VDC 2A with country adapters (EU, UK; US, AUS)
  • 2x thermal conductive pad
  • 2x thermal conductive plate
  • 4x M.2 rubber plug
  • Lindy Manual

Specification

  • Interface: USB to 2x PCIe/NVMe M.2 SSD
  • Interface Standard: USB 3.2 Gen 2×2, PCIe 3.0 x2
  • Supported Bandwidth: 20Gbps (USB), 32Gbps – each up to 16Gbps (PCI 3.0 x2)
  • Chipset: JMS586U
  • Compatibility: USB Type C equipped computers
  • Special Features: supports 42/60/80mm SSDs, UASP & TRIM, LED indicator for Clone process
  • Inputs: 1 x USB Type C (Female)
  • Outputs: 2 x PCIe based M.2 (Female), M key and B+M key
  • Power: 5.5/2.5mm DC socket
  • Product Dimensions WxDxH: 143x77x17.5mm (5.63×3.03×0.69in)
  • Housing Material: Aluminium and ABS
  • Net Weight: 0.174kg (0.38lb)
  • Operating Temperature: 5°C – 35°C (41°F – 95°F)
  • Storage Temperature: -10°C – 90°C (-14°F – 122°F)
  • Humidity: 10 – 90% RH (non-condensing)

Overview

  • Offline Clone Button
  • Upstream Port: USB 3.2 Gen 2×2 20Gbps Type C Female
  • Power Port: 12V DC 5.5×2.5mm
  • LED Indicators for Power, M.2 NVMe SSD and Offline Clone Progress
  • Secure-Lock: Lock & Unlock

Installation & Operation

Please follow the steps below for installation:

  • Press once on the plastic inner frame at the other side of the housing until it pops out
  • Insert the M.2 NVMe SSD(s) into the product, gently press down the M.2 SSD(s) and snap it into the rubber plug.

Paste the thermal conductive pad on the SSD and finally the thermal conductive plate on top (please remove the surface layers on both sides first). Finally push the plastic frame back into the Aluminium
housing and lock the secure lock E by sliding the switch to the left. Please note: If you want to clone SSDs, do not connect the USB 3.2 Dual M.2 NVMe SSD Enclosure to your computer

Offline Clone Operation

  • Install two M.2 NVMe SSDs* (the storage capacity of disk B (target disk) should be larger or equal todisk A (source disk), then connect the power supply to the enclosure.
  • Press and hold the clone button A for about 3 seconds until all 4 blue LEDs light up, then release the  button and quickly press it again, offline clone begins.
  • 4 indicators of progress light up in blue when offline cloning is in progress, 25% > 50% > 75% > 100% flickers in turn, all 4 indicators light up when offline clone is done.

*Read and Write Access to SSDs (no cloning)**
Please connect the included power supply and the USB Type C cable to the USB 3.2 Dual M.2 NVMe SSD Enclosure. The operating system will install necessary drivers automatically and the Enclosure is now ready for use. Reading of and writing on two SSDs simultaneously is supported. Before unplugging the USB 3.2 Dual M.2 NVMe SSD Enclosure make sure data transfer processes are completed to avoid data loss.

LED Indicators (from top to bottom)

  • Power Indicator: lights up in green when the power is on.
  • M.2 NVMe SSD Indicators: Light up in yellow when the M.2 NVMe SSD is inserted, flickers while reading and writing; the indicator is off in sleep mode.
  • Offline Clone Progress Indicators:
  • Light up in blue when offline cloning is in progress: 25% > 50% > 75% > 100% flicker in turn, all 4 indicators light up when the clone process is finished;
  • The LED of disk A flickers to report an error while the storage capacity of target disk (disk B) is less than source disk (disk A) during offline cloning.
  • If you are using a new M.2 SSD, it must first be initialized, formatted and partitioned.

Recycling Information
WEEE (Waste of Electrical and Electronic Equipment), Recycling of Electronic Products Europe, United Kingdom In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process. Each individual EU
member state, as well as the UK, has implemented the WEEE regulations into national law in slightly different ways. Please follow your national law when you want to dispose of any electrical or electronic products. More details can be obtained from your national WEEE recycling agency.

CE/FCC Statement
LINDY declares that this equipment complies with relevant European CE requirements.

FCC Certification

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. You are cautioned that changes or modification not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

The enclosed power supply has passed Safety test requirements, conforming to the US American versions of the international Standard IEC 60950-1 or 60065 or 62368-1.
Hersteller / Manufacturer (EU): Manufacturer (UK): LINDY-Elektronik GmbH LINDY Electronics Ltd
Markircher Str. 20 Sadler Forster Way 68229 Mannheim Stockton-on-Tees, TS17 9JY

Germany England
Email: info@lindy.com, T: +49 (0)621 470050 sales@lindy.co.uk, T: +44 (0)1642 754000

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals