blizzard TOURnado RGBALC RGBAW+UV Color Mixing User Guide

than 3 seconds between each button press.

CUSTOM| CT01-CT10| < ENTER>| R/G/B/A/L/C adjustments for custom color banks 01-10
AUTO| AT01-AT05| < ENTER>| Auto programs 1-5
ATSP| < ENTER>| Auto speed 0-255 (fast to slow)
CHS1| < ENTER>| Custom program 1
CHS2| < ENTER>| Custom program 2
CHS3| < ENTER>| Custom program 3
PROG| CHS1- CHS3

Custom programs 1-3.

| SC01-SC25

25 scenes for each custom program.

| R (0-255)| SHUT (strobe, 0-255)
G (0-255)| AUTO (None, AT01-AT05)
B (0-255)| ATSP (speed, 0-255 seconds)
A (0-255)| TIME (duration, 0-255 seconds)
L (0-255)| WAIT (before fade, 0-255 seconds)
C (0-255)| USE (use scene, YES/NO)
INFO| SOFTWARE| Software version information
TEMP| Display the internal temperature of the fixture
POWER| Current automated overheat protection level (100%/80%/50%)
LOAD| ST L| Restore factory settings
PR L| Restore factory program settings
SEND| YES/NO| Sync settings between fixtures via DMX

DMX Mode

Allows the unit to be controlled by any universal DMX controller.

Setting the DMX Address:

1. The default mode for the fixture is DMX, which appears as 001 on the LED readout. To select a different DMX address, using the button, select ADDR, then hit . Use the <UP/DOWN> buttons to select the correct address, then hit to confirm.

Setting the DMX Channel Mode:

1. To select a DMX channel mode, press the button, then use the <UP/DOWN> buttons until the display reads SET and press the button. Then use the <UP/DOWN> buttons until the display reaches CHMD, and press . Now press the <UP/DOWN> buttons again to highlight your desired DMX channel mode, and press the button to confirm.

Slave Mode:

1. Daisy chain the DMX in/out connections on all fixtures.
2. There is nothing else to it! The first fixture in the DMX chain is the master fixture, and the other fixtures down the line will follow it.

Dimming Mode Settings

Allows users to set the fixture to use 1 of 4 (x2) dimming curve settings for smoother (and slower) dimming capabilities. In the control panel menu, there are two settings for each curve that are distinguishable from one another by the trailing dot.

The curve settings with the trailing dot adds a bit more delay to the curve for a smoother effect.

1. Use the and <UP/DOWN> buttons to navigate to SET and press , then <UP/DOWN> buttons again to scroll to DIM, and press the button.
2. Now use the <UP/DOWN> buttons to highlight either LIN (Linear), SQR (Square), ISQR (Inverse Square), SCUR (S-Curve), LIN. (Smooth Linear), SQR. (Smooth Square), ISQR. (Smooth Inverse Square), or SCUR. (Smooth S-Curve), then hit .

Custom Programs

Allows users to create up to 3 customizable, 25 scene programs that are directly accessible via the control panel and also in DMX mode.

Creating A Custom Program:

1. Use the and <UP/DOWN> buttons to navigate to PROG, and press .
2. Now use the <UP/DOWN> buttons to highlight your choice of either CHS1, CHS2, or CHS3 and press .
3. Start with editing scene 1 (SC01), customizing it to your liking by using the choices outlined in the table below. You can insert any of its 5 built-in auto programs (AT01-AT05), and adjust its speed (ATSP 0-255), and also set the duration (in seconds) before moving on to the next scene (TIME 0-255). You can also add a fade in effect to the start of this scene (WAIT 0-255), and/or strobe (SHUT 0-255). Finally, if you want to use this scene in your program, be sure to enable it (USE: YES/NO).
4. Repeat the above process to create up to 25 scenes in each of the 3 customizable programs.

R (0-255) – Red Intensity| C (0-255) – Cyan Intensity| WAIT (0-255) – Fade In (fast – slow)
---|---|---
G (0-255) – Green Intensity| SHUT (0-255) – Strobe (slow – fast)| USE (YES/NO) Use Scene in Program?
B (0-255) – Blue Intensity| AUTO (AT01-AT05) – Auto Programs| _ _IMPORTANT:__

If USE is set to NO, or TIME is set to 0, the scene will not run!

A (0-255) – Amber Intensity| ATSP (0-255) – Auto Speed (fast – slow)
L (0-255) – Lime Intensity| TIME (0-255) – Scene Time (seconds)

Running A Custom Program:

1. To view your newly created lighting masterpiece, use the and <UP/DOWN> buttons to navigate to AUTO, and press .
2. Use the <UP/DOWN> buttons to highlight your choice of CHS1, CHS2, or CHS3 and press . These are directly accessible from the built-in program channel in DMX mode.

Auto, Modes, and Auto Speed

Set single or Master/Slaved units to run auto modes at user-selectable speeds.

Auto Mode:

1. Use the and <UP/DOWN> buttons to navigate to navigate to AUTO, and press the button.
2. Now use the <UP/DOWN> buttons to highlight any program ranging from AT01-AT05, and press .

Auto Speed:

1. Use the and <UP/DOWN> buttons to navigate to AUTO and press , then with the <UP/DOWN> buttons navigate to ATSP, and press the button.
2. Make a selection from 0-255, and press to choose a speed (slow <–> fast).

Color Calibration Settings

Allows the user to setup and save 1 customized R/G/B/A/L/C color balance setting and save it for future use. This custom setting is global, and it will effect all modes.

1. Use the and <UP/DOWN> buttons to navigate to SET and press , then on while CAL, push again.
2. Use the <UP/DOWN> buttons to highlight either R (Red Level), G (Green Level), B (Blue Level), A (Amber Level), L (Lime Level), or C (Cyan Level) then hit .
3. Now using the <UP/DOWN> buttons, select the maximum level for each color between 000-255 (000=off), and hit to confirm your choice.
4. You have now just setup and saved a custom global color calibration setting that you can use at you convenience. To use your custom setting now (or later), press the <UP/DOWN> buttons to reach USE, and press . Then choose either YES or NO and press . When you select YES, it enables this custom color calibration globally, and when choosing NO the fixture will continue to use the default color calibration settings. Your customized settings will be saved for later use even after powering off the fixture. It can be altered to your liking at any time. Just remember to return to this setting to either enable or disable it when needed.

Custom Static Colors & Preset Colors

Allows the user to create and save custom static colors for use in standalone or DMX mode.

Static Color Mixing and Preset Mixed Colors
Important: When finished editing and saving a static color, you must return to (and stay on) any one of the editing screens (0-255) to make the effect stay on continually. If you were only to press to save your final edit, you would again be on the static color/effect selection menu, which from here will result in blackout mode after 1 minute.

1. Use the and <UP/DOWN> buttons to navigate to STAT and press , then <UP/DOWN> buttons to select R/G/B/A/L/C, and push to confirm your selection. Then in adjust the values (0-255) to your liking and press to save.
2. In the same manner, you can select SHUT to add a strobe effect.
3. You can also select and use the <UP/DOWN> buttons to scroll through and quickly use any of the fixtures built-in preset colors.

Mix and Save Custom Colors (1-10)

1. Use the and <UP/DOWN> buttons to navigate to CTST and press , then <UP/DOWN> buttons to select a color bank from CT01-CT10, and push to confirm your selection.
2. Now use the <UP/DOWN> buttons to highlight either R (Red Level), G (Green Level), B (Blue Level), A (Amber Level), L (Lime Level), or C (Cyan Level) then hit .
3. Finally, using the <UP/DOWN> buttons, select the maximum level for each colour between 000-255 (000=off), and hit to confirm your choice(s).
4. These 10 custom colors can be accessed and edited to your liking at any time, and will be saved even after powering off the fixture.
5. Your custom colours and programs are also directly accessible from the built-in program channel in DMX mode.

Fixture Reset Functions

Allows users to reset the fixture to factory default settings, without loosing customized settings, or reset the custom programs exclusively.

1. Use the and <UP/DOWN> buttons to navigate to LOAD and press , then use the <UP/DOWN> buttons to highlight ST L or PR L, and press .
2. Use the <UP/DOWN> buttons to highlight either YES or NO, then press .
3. The ST L reset function will reset all default values with the exception of those in ADDR (address), CTST (10 custom colors), and PROG (custom scenes and programs).
4. The PR L reset function will only reset all customized program settings found in the PROG settings (custom scenes and programs).

Data Sync Feature

Users can transfer their custom settings from one fixture to another via DMX.

1. Disconnect fixtures from any DMX controllers, and link them together via DMX in/out.
2. On the sending fixture (DMX out), navigate the main menu using the <UP/DOWN> buttons to reach SEND, and press the button.
3. Select YES, and press the button to begin the transfer.
4. Information for ADDR (address), or CAL (global intensity) will not be sent.
5. After the data has been transferred, the receiving fixture will be automatically be reset.

Fixture Information

These are not editable features, they are for informational purposes only.

1. Use the and <UP/DOWN> buttons to navigate to INFO and press , then use the <UP/DOWN> buttons to highlight SOFT or POW, and press .
2. The SOFT information simply displays the current software version installed on the fixture, and POW displays the fixtures current power level setting. Under normal conditions, it will be at 100%… but this fixture has built-in overheat protection that may automatically reduce the output level to 80%, or 50% in high temperature situations.

DMX Values In-Depth (6/8/12-Channel Modes)

Troubleshooting

operating

under the correct working mode.

Dim Output| Check the overheat protection level in the menu. If it has been

triggered, ensure that the fixture has sufficient ventilation.

Chase Speed Too Fast/Slow| Verify that the speed adjustment settings are correct.
Loss of DMX Control| Check the DMX and the power connections to make sure that they are connected.

Make sure the DMX address setting is correct. Check to see if the channel mode setting is correct.

No Power| Verify that the power cord and circuit are functioning.
Blown Fuse| Check power cords and circuit for damage.
Fixture Not Responding / Responding Errati- cally| Make sure all connectors are seated properly and securely. Use only DMX cables and/or check cables for defects.

Install a DMX signal terminator.

Reset fixture(s).

APPENDIX

Keeping Your TOURnado™ RGBALC As Good As New
The fixture you’ve received is a rugged, tough piece of pro lighting equipment, and as long as you take care of it, it will take care of you. Cleaning the optics routinely with a suitable glass cleaner will greatly improve the quality of light output. In transit, keep the fixtures in cases. Common sense and taking care of your fixtures will be the single biggest thing you can do to keep them running at peak performance and let you concentrate on designing a great light show. That’s what it’s all about, after all!

Returns (Gasp!)

We’ve taken a lot of precautions to make sure you never even have to worry about sending a defective unit back, or sending a unit in for service. But, like any complex piece of equipment designed and built by humans, once in a while, something doesn’t go as planned. If you find yourself with a fixture that isn’t behaving like a good little fixture should, you’ll need to obtain a Return Authorization (RA). Don’t worry, this is easy. Just

• visit www.blizzardpro.com/support

and open a support ticket, and we’ll issue you an RA. Then, you’ll need to send the unit to us using a trackable, pre-paid freight method. We suggest using USPS Priority or UPS. Make sure you carefully pack the fixture for transit, and whenever possible, use the original box & packing for shipping.
When returning your fixture for service, be sure to include the following:

1. Your contact information (Name, Address, Phone Number, Email address).
2. The RA# issued to you
3. A brief description of the problem/symptoms.

We will, at our discretion, repair or replace the fixture. Please remember that any shipping damage which occurs in transit to us is the customer’s responsibility, so pack it well!

Shipping Issues

Damage incurred in shipping is the responsibility of the shipper, and must be reported to the carrier immediately upon receipt of the items. Claims must be made within seven (7) days of receipt.

Tech Specs!

Weight & Dimensions

Width| 11.4 inches (289 mm)
Depth| 6.5 inches (163 mm)
Height| 12.5 inches (317 mm)
Weight| 9.7 lbs (4.4 kg)
Power
Operating Voltage| AC 100V-240V/50-60Hz
Power Consumption| 112W, 1.48A, PF: .65
Light Source
LED| 7x 20W RGBALC 6-in-1 LEDs (100,000 hours)
Optical
Luminous Intensity| 6,204 Lux @ 2.5M, 1,401 Lux @ 5M
Beam Angle| 25-degree beam
Thermal
Max. Operating Temp.| 104 degrees F (40 degrees C) ambient
Control
Protocol| USITT DMX-512
DMX Channels| 6/8/12-channel DMX modes
Input/Output| 5-pin XLR Male/Female
Other Operating Modes| DMX512, M/S, Standalone, Auto Mode

Warranty

| 2-year limited warranty, does not cover malfunction caused by damage to LEDs.

Photometric Data Luminous Intensity:

2-meter/3-meter/4-meter/5-meter

References

• LED Lighting Products + IRiS LED Video | Blizzard Lighting
• LED Lighting Products + IRiS LED Video | Blizzard Lighting
• Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>