Blizzard BCT2 Electric Conveyor Toaster User Manual
- June 5, 2024
- blizzard
Table of Contents
Blizzard BCT2 Electric Conveyor Toaster
Owner information
General
This Electric Conveyor Toaster is specially designed to speed the toasting operation. Products for toasting pass through a heating chamber for rapid and thorough toasting of products. Dryness, moisture, sugar content and thickness of bread product affect the ability to achieve the perfect toasted product. Conveyor speed, not temperature, determines the toasting colour.
Warranty Information
This manual provides the installation, safety and operating instructions for the Electric Conveyor Toasters. We recommend all installation, operating and safety instructions appearing in this manual be read prior or installation or operation of your ConveyorToaster. Safety instructions that appear in this manual after a warning symbol and the words WARNING or CAUTION printed in bold face are very important. WARNING means there is the possibility of serious injury or death to yourself or others. CAUTION means there is the possibility of minor or moderate injury. CAUTION without the symbol signifies the possibility of equipment or property damage only. This Electric Conveyor Toaster is a product of extensive research and field testing. The materials used were selected for maximum durability, attractive appearance, and optimum performance. Every unit is thoroughly inspected and tested prior to shipment.
IMPORTANT! Keep these instructions for future reference. If the unit changes ownership, be sure this manual accompanies the equipment
Throughout this manual, you will find the following safety words that signify important safety issues with regards to operating or maintaining the equipment.
WARNING
GENERAL WARNING. Indicates informa- tion important to the proper operation of
the equipment. Failure to observe may result in damage to the equipment and/or
severe odRoily inutinejury or inspec death.t ion
CAUTION
GENERAL CAUTION. Indicates informa- tion Important to the proper operation of
the equipment. Failure to observe may result in damage to the equipment.
WARNING
ELECTRIC WARNING. Indicates informa- tion relating to possible shock hazard.
Failure to observe may result in damage to the equipment and/or severe bodily
injury or death
WARNING
HOT SURFACE WARNING. Indicates information Important to the proper operation
of the equipment. Failure to observe may result in damage to the equipment.
WARNINGS
- Plug toaster into a properly grounded electrical outlet of the correct voltage, size, and plug configuration. If the plug and receptacle do not match, contact a qualified electrician to determine the proper voltage and size, and install the proper electrical outlet.
- To avoid any injury, turn the power switch off, unplug the unit from the power source and allow to cool before performing any maintenance.
- For safe and proper operation, the unit must be located at a reasonable distance form combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur. Do not locate toaster under shelving or closer than 12″(31 cm) from the ceiling.
- Allow a minimum of 1″(3cm) clearance along the sides. Allow a clearance of 12″(31cm) along the front and rear discharge to ensure proper operation and safety.
- To prevent any injury or damage do not pull unit by power cord.
- To prevent any injury, discontinue use if power cord is frayed or worn.
CAUTIONS
- Locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or its contents from accidentally falling, and strong enough to support the weight of the unit.
- Do not place anything on top of the toaster; doing so could damage toaster or subject personnel to possible injury.
- The toasting of coated or buttered products such as garlic bread, cheese sandwiches and sweet rolls is NOT recommended. Residue will reduce toaster performance and could possibly ignite inside the toaster.
- When setting up the unit for operation, make sure power to the unit is off and the toaster is at room temperature. Failure to do so could result in personal injury.
- To avoid damage to the unit or injury to personnel always operate toaster with crumb tray installed.
- To avoid any injury, do not remove the crumb tray for cleaning until toaster is cool.
- Unit is not weatherproof. For safe and proper operation locate the unit indoors where the ambient air temperature is a minimum of 70°F(21℃) and a maximum of 85°F(29℃)
CAUTIONS
Do not locate the toaster in an area subject to excessive temperature or grease from grills, fryers, etc. Excessive temperature could cause damage to the unit. Do not place toaster in an area that restricts air flow around the front or rear of the unit. Do not place toaster in direct discharge path of air conditioning vent or makeup air vent. Use only non-abrasive cleaners. Abrasive cleaners could scratch the finish of your toaster marking its appearance and making it susceptible to soil accumulation.
UNPACKING
- Remove unit and all packing materials from shipping carton.
- Open the large box. Remove all packing materials and protective covering from the unit and parts.
- Remove tape from discharge chute, crumb tray and toast collector pan.
- If unit is not level, use 9/16″(14cm) open-end wrench to adjust the foot of each leg until unit is level.
LOCATION
CAUTION
- Do not locate the toaster in an area subject to excessive temperatures or grease from grills, fryers, etc. Excessive temperatures could cause damage to the unit.
- Do not place toaster in an area that restricts air flow around the front or rear of the unit. Do not place toaster in direct discharge path of air conditioning vent or makeup air vent.
WARNING
For safe and proper operation, the unit must be located a reasonable distance from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur. Do not locate toaster under shelving or closer than 12″(31cm) from the ceiling. Allow a minimum of 1″(3cm ) clearance along the sides. Allow clearance of 12″(31cm) along the front and rear discharge to ensure proper operation and safety.
CAUTION
Locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or its contents from accidentally falling, and strong enough to support the weight of the unit. Do not place anything on top of the toaster; doing so could damage toaster or subject personnel to possible injury.
SET-UP
CAUTION
Unit is not weatherproof. For safe and proper operation locate the unit indoors where the ambient air temperature is a minimum of 70°F(21℃) and a maximum of 85°F(25℃). The toasting of coated or buttered products such as garlic bread, cheese sandwiches and sweet rolls is NOT recommended. Residue will reduce toaster performance and could possibly ignite inside the toaster. When setting up the unit for operation, make sure power to the unit is off and the toaster is at room temperature. Failure to do so could result in personal injury.
TOAST FEED RAMP
The toast feed ramp is installed at the factory and can be used in two positions.
- When in the upright position, the toaster is set for automatic feed. Bread products enter the toaster by placing them on the feed ramp and releasing.
- For manual feeding of product, tip the feed ramp until it rests on top of the unit. In this position bread products can be manually loaded by placing them directly on the conveyor belt.
CAUTION
Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury.
TOAST CRUMB TRAY
Install toast crumb tray directly below the conveyor belt and below the stop pins. Insert until the front of the crumb tray meets the stop pins. To avoid damage to the unit or injury tot personnel always operate toaster with crumb tray installed. To avoid any injury, do not remove the crumb tray for cleaning until toaster is cool.
FRONT/REAR DISCHARGE
The toaster can be configured to discharge in the front or rear. User can pull up the rear discharge door for front discharge and push down the rear discharge door for rear discharge.
FOR MODEL EQUPPED WITH ROCKER SWITCH
-
Plug toaster into a properly grounded electrical outlet of the correct voltage, size and plug configuration. (See the Rating Label)
-
Place the On/Off switch in the On position.
-
Turn the Colour Control to the lightest position while the unit heats up.
(Note: Allow approximately 15 to 21 minutes for a warm-up period.) -
After warm-up period, set the Colour Control to the medium position and toast two slices of bread product then re-adjust the Colour Control to the desired setting.
(Note: To toast moist products such as English Muffins, rye bread or whole wheat, slow the conveyor by turning the Colour Control knob to a darker setting (clockwise)).
FOR MODEL EQUIPPED WITH ROTARY SELECTOR
-
Plug toaster into a properly grounded electrical outlet of the correct voltage, size and plug configuration. (See the Rating Label)
-
Rotate the Rotary switch in the high-heat position.
-
Turn the Colour Control to the lightest position while the unit heats up.
(Note: Allow approximately 15 to 20 minutes for a warm-up period.) -
After warm-up period, set the Colour Control to the medium position and toast two slices of bread product then re-adjust the Colour Control to the desired setting.
(Note: To toast moist products such as English Muffins, rye bread or whole wheat, slow the conveyor by turning the Colour Control knob to a darker setting (clockwise)). -
This unit can be used for one sided toasting, such as buns and English Muffins by rotating the rotary switch to the top side heat only (buns).
POWER SAVE MODE
Selected this toaster can go into a Power Save Mode by turning the rotary
selector into Power Save Mode. The toaster is operating at 25% power.
(Note: To place toaster back into full operation turn the selector back
in to TOAST. Unit is back up to full power within 5 minutes.)
GENERAL
The Electric Conveyor Toasters are designed for maximum durability and performance, with minimum maintenance.
WARNING
TO AVOID ANY INJURY, TURN THE POWER SWITCH OFF, UNPLUG THE UNIT FORM THE POWER SOURCE AND ALLOW TO COOL BEFOR PERFORMING ANY MAINTENANCE.
LEANING
Exterior
To preserve the bright finish of the unit, it is recommended that the exterior
surfaces be wiped daily with a damp cloth. Stubborn stains may be removed with
a good stainless-steel cleaner or non-abrasive cleaner. Hard to reach areas
should be cleaned with a small brush and mild soap.
CAUTION
USE ONLY NON-ABRASIVE CLEANERS. ABRASIVE CLEANERS COULD SCRATCH THE FINISH OF
YOUR TOASTER MARRING ITS APPEARANCE AND MAKING IT SUSCEPTIBLE TO SOIL
ACCUMULATION.
Toast Crumb Tray & Toast Collector Pan
Remove from unit and wash with soap and water, then rinse.
Toast Feed Ramp
Press in the two wire spokes and remove guide form unit. Wipe clean with a
soft, damp cloth or soak the guide in a mild solution of 1 cup ammonia and 1
gallon of water (227 millilitres and 3.785 litres). Re-install guide by
aligning wire spokes with holes in toaster.
Disposal
EU regulations require products to be disposed of by specialist companies who remove or recycle products, including electronic, metal and plastic components. Consult your local waste collection authority regarding disposal of your appliance. Local authorities are not obliged to dispose of commercial equipment but may be able to offer advice on how to dispose of the equipment locally. All packaging materials should be disposed of in an environmentally friendly way. The cardboard may be used as scrap paper. The protective foil and the foam cushions are CFC-free. Do not allow children to play with the packaging and destroy plastic bags safely.
Environmental protection
Discarded electric appliances are recyclable and should not be discarded in the domestic waste! Please actively support us in conserving resources and protecting the environment by returning this appliance to the collection centres (if available).
Compliance
Parts have undergone strict product testing in order to comply with regulatory standards and specification set by international, independent, and federal authorities. Products have been approved to carry the following symbol: Pentland Wholesale Ltd. Unit17 Walker Park Industrial Estate Walker Rd., Blackburn, BB1 2QE. TEL: 01254614444 www.pentlandwholesale.co.uk
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>