LOFTNESS Battle Ax Light Skid Loader Mulching Head User Manual

June 16, 2024
LOFTNESS

Battle Ax Light Skid Loader Mulching Head

Product Information

Specifications

  • Model Number: Battle Ax Light
  • Serial Number: 93-370 thru 93-619
  • Date of Purchase: 07.27.21
  • Manufacturer: Loftness Specialized Equipment, Inc.
  • Warranty: One (1) year limited warranty for all Loftness
    products, except the XLB10 Grain Bag Loader which has a two (2)
    year limited warranty.

Product Usage Instructions

1. Warranty Requirements

In order to validate all warranty claims, please ensure the
following:

  • Fill out and return the warranty registration form to Loftness
    Specialized Equipment.

  • Obtain a return authorization from Loftness before returning
    any failed part.

  • Return the failed part in an untampered status.

Note: This warranty does not cover freight or delivery charges
incurred when returning machinery for servicing. Dealer mileage,
service calls, and pick-up/delivery charges are the customer’s
responsibility.

2. Limitations of Warranty

The limited warranty provided by Loftness has the following
limitations:

  • Proper use and maintenance must be adhered to for years of
    dependable service.

  • This warranty does not cover general wear or maintenance items,
    misuse, environmental conditions, and/or contamination for which
    they were not designed or intended.

3. Pre-Delivery Inspection (PDI)

Prior to using the Loftness attachment, it is imperative to
complete the following Pre-Delivery Inspection using the customer’s
actual power unit:

  • Verify that the attachment is set up properly for the
    customer’s power unit by checking the model code with the
    manual.

  • Grease all grease zerks until grease purges out of the
    bearing.

  • Remove all shipping brackets.

  • Adjust the push bar out of the shipping position (if equipped).
    The full forward position is recommended.

Frequently Asked Questions (FAQ)

1. How long is the warranty period for Loftness products?

All Loftness products come with a one (1) year limited warranty,
except for the XLB10 Grain Bag Loader which has a two (2) year
limited warranty.

2. What does the warranty cover?

The warranty covers defects in material and workmanship when the
product is properly set up and operated according to the
recommendations in the Loftness Operator’s Manual.

3. How can I validate my warranty claim?

To validate your warranty claim, you need to fill out and return
the warranty registration form to Loftness Specialized Equipment.
Additionally, you must obtain a return authorization from Loftness
before returning any failed part.

4. Who is responsible for freight and delivery charges when

returning machinery for servicing?

The customer is responsible for freight or delivery charges
incurred when returning machinery for servicing. Dealer mileage,
service calls, and pick-up/delivery charges are also the customer’s
responsibility.

5. What is covered by the warranty exclusions?

The warranty exclusions include general wear or maintenance
items, misuse, environmental conditions, and/or contamination for
which the product was not designed or intended.

203417 Rev. F

Battle Ax Light
Skid Loader Mulching Head
51 · 61
Owner’s Manual and Parts Book (Originating w/Serial Number 93-370 thru 93-619)
Model Number: Serial Number: Date of Purchase:

07.27.21

LOFTNESS SPECIALIZED EQUIPMENT, INC. LIMITED WARRANTY POLICY

The limited warranty policy begins upon delivery of the unit to the original customers.
All Loftness products have a one (1) year limited warranty. The XLB10 Grain Bag Loader has a two (2) year limited warranty.
If any Loftness product is used as rental or leased equipment the limited warranty period is for only 30 days from the delivery date to the original customers.
Loftness Specialized Equipment, hereinafter referred to as LOFTNESS, a manufacturer of quality machinery since 1956, warrants new LOFTNESS machinery and/or attachments at the time of delivery to the original purchaser, to be free from defects in material and workmanship when properly set up and operated in accordance with the recommendations set forth in the LOFTNESS Operator’s Manual.
LOFTNESS’ liability for any defect with respect to accepted goods shall be limited to repairing the goods at an authorized dealer or other LOFTNESS designated location, or replacing them as LOFTNESS shall elect. The above shall be in accordance with LOFTNESS warranty adjustment policies.
WARRANTY REQUIREMENTS
Warranty registration form must be filled out and returned to Loftness Specialized Equipment to validate all warranty claims. To receive a warranty claim, a return authorization from LOFTNESS must be obtained. The failed part may then be returned in an untampered status. This warranty does not include freight or delivery charges incurred when returning machinery for servicing. Dealer mileage, service calls and pick-up/delivery charges are the customer’s responsibility.
LIMITATIONS OF WARRANTY
LOFTNESS products are designed to provide years of dependable service when proper use and maintenance is adhered to. The potential for misuse in many applications exists; therefore, a limited warranty is provided as follows.
This warranty shall not apply to any machine or attachment which shall have been repaired or altered outside the LOFTNESS factory or authorized LOFTNESS dealership or in any way so as in LOFTNESS’ judgment, to affect its stability or reliability, nor which has been subject to misuse, negligence or accident, nor to any machine or attachment which shall not have been operated in accordance with LOFTNESS’ printed instructions or beyond the company recommended machine rated capacity. LOFTNESS may elect to have an area representative evaluate the condition of the machine before warranty is considered.
In addition, this limited warranty provides no coverage for general wear or maintenance items, misuse, environmental conditions and/or contamination for which they were not designed or not intended, including but not limited to the following items:
· Use of machine beyond its rated capacity; · Improper knife replacement; · Missing knives; · Striking foreign objects · Lack of lubrication · Failures caused by running in an “out-of-balance” condition; · Tires; · Conveyors; · Auger wear; · Saw blades; · Brakes and brake pads; and · Hydraulic hoses damaged by being caught in “pinch points” or by moving parts.

EXCLUSIONS OF WARRANTY

Except as otherwise expressly stated herein, LOFTNESS makes no representation or warranty of any kind, expressed or implied. The implied warranty of merchantability and fitness for a particular purpose are excluded from this limited warranty. The remedies set forth in this warranty are the only remedies available to any person under this warranty. LOFTNESS shall have no liability to any person for incidental, consequential or special damages of any description, whether arising out of express or implied warranty or any other contract, negligence, or other tort or otherwise. This exclusion of consequential, incidental and special damages is independent from and shall survive any finding that the exclusive remedy failed of its essential purpose. Upon purchase, the buyer assumes all liability, all personal injury and property damage resulting from the handling, possession or use of the goods by the buyer.

No agent, employee or representative of LOFTNESS has any authority to bind LOFTNESS to any affirmation, representation or

warranty concerning its machinery and/or attachments except as specifically set forth herein.

(October 2020)

To the Dealer:
In order to ensure compatibility / performance of the Loftness attachment and the customer’s power unit, it is IMPERATIVE that this Pre-Delivery Inspection (“PDI”) be completed using the customer’s actual power unit.

PRE-DELIVERY INSPECTION
Dealer: By initialing each line I understand and promise that I have completed the following:

____ Verified the attachment is set up properly for customers power unit. (check model code with manual)

____ Greased all grease zerks till grease purges out of bearing.

____ Removed all shipping brackets.

____Adjusted push bar out of shipping position. (if equipped) (full forward position recommended)

____ Installed head on customer’s unit that will be running the attachment and set hydraulic flow per power unit manufacturer owner’s manual for preferred flow.

____ Recorded the Serial Number / Make / Model of the power unit.

Power unit. S/N _____ Make ____ Model


Recorded the Serial Number and Model of the Loftness attachment. S/N ____ Model

____ Verified power unit manufacturer outlined Auxiliary coupler orientation for pressure, return & case drain line.

__ Verified/recorded rotor RPM at full throttle per model & chart in Loftness owner’s manual. RPM ___

____ Performed an Auxiliary system pressure stall check on the power unit only and verified that max pressure rating is

achieved per power unit manufacturer specifications.

Recorded pressure observed ___ PSI

PDI completed by: ____ Print

____ Signed/Date Contact Loftness factory if any of the tests are not within power unit or Loftness specifications.
DELIVERY
____ Showed customer all grease zerks.

____ Showed customer adjustable push bar options. (if equipped)

____ Showed customer how to properly engage hydraulics to operate attachment.

____ Reviewed owner’s manual, all on-product warnings and instructions, and safe operation with customer.

____ Assisted customer with completing / submitting Warranty Registration Form to Loftness by one of the below options. Dealer also needs to submit a copy of this completed PDI to Loftness and maintain the copy in owner’s manual for unit.

Mail to: Loftness Specialized Equipment PO Box 337 Hector, MN 55342

Delivered to Customer by: Print Signed/Date

Email to: Cheryl Schmalz Cheryl@loftness.com

LOFTNESS COPY

To the Dealer:
In order to ensure compatibility / performance of the Loftness attachment and the customer’s power unit, it is IMPERATIVE that this Pre-Delivery Inspection (“PDI”) be completed using the customer’s actual power unit.

PRE-DELIVERY INSPECTION
Dealer: By initialing each line I understand and promise that I have completed the following:

____ Verified the attachment is set up properly for customers power unit. (check model code with manual)

____ Greased all grease zerks till grease purges out of bearing.

____ Removed all shipping brackets.

____Adjusted push bar out of shipping position. (if equipped) (full forward position recommended)

____ Installed head on customer’s unit that will be running the attachment and set hydraulic flow per power unit manufacturer owner’s manual for preferred flow.

____ Recorded the Serial Number / Make / Model of the power unit.

Power unit. S/N _____ Make ____ Model


Recorded the Serial Number and Model of the Loftness attachment. S/N ____ Model

____ Verified power unit manufacturer outlined Auxiliary coupler orientation for pressure, return & case drain line.

__ Verified/recorded rotor RPM at full throttle per model & chart in Loftness owner’s manual. RPM ___

____ Performed an Auxiliary system pressure stall check on the power unit only and verified that max pressure rating is

achieved per power unit manufacturer specifications.

Recorded pressure observed ___ PSI

PDI completed by: ____ Print

____ Signed/Date Contact Loftness factory if any of the tests are not within power unit or Loftness specifications.
DELIVERY
____ Showed customer all grease zerks.

____ Showed customer adjustable push bar options. (if equipped)

____ Showed customer how to properly engage hydraulics to operate attachment.

____ Reviewed owner’s manual, all on-product warnings and instructions, and safe operation with customer.

____ Assisted customer with completing / submitting Warranty Registration Form to Loftness by one of the below options. Dealer also needs to submit a copy of this completed PDI to Loftness and maintain the copy in owner’s manual for unit.

Mail to: Loftness Specialized Equipment PO Box 337 Hector, MN 55342

Delivered to Customer by: Print Signed/Date

Email to: Cheryl Schmalz Cheryl@loftness.com

CUSTOMER COPY

Table of Contents
Warranty
Table of Contents
Ordering Code
Ordering Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Battle Ax Light – Skid Loader (Example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Introduction
Owner Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warranty Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Serial Number Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Battle Ax Light Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Manual Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety Instructions
Safety First. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Owner’s Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Mandatory Shut-Down Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Hydraulic Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 California Proposition 65 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Safety Decal Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Battle Ax Light Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Set-up Instructions
Pusher Bar Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Remove Shipping Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Installing the Battle Ax Light to the Loader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Hydraulic Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Checking Rotor Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Checking Rotor Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Cutter Bar Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Operating Instructions
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Clearing Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Log Moving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Detaching Battle Ax Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Maintenance
General Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Grease Points Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Overhung Load Adapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Battle Ax Light – Skid Loader OM

Table of Contents
Maintenance (Cont’d)
Removing Belt Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Removing Left End Bearing Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Removing Motor Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Removing Hose Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Skid Removal/Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Belt Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Tooth Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Tooth Sharpening. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
End of Season . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Beginning of the Season . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Motor & Sheave Selection Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Parts Identification
Covers, Manual Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Rotor, Skid Shoes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Cutter Bar, Deflector Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Pusher Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Motor Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Motor Cover (203233) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Belt and Sheave, 3/B BSL “A” (8.6″ Top, 6.2″ Bottom) (203411) . . . . . . . . . . . . . . . . . . . . . . . 36 Belt and Sheave, 3/B BSL “B” (8″ Top, 6.8″ Bottom) (203412) . . . . . . . . . . . . . . . . . . . . . . . . . 37 Belt and Sheave, 3/B BSL “C” (7.4″ Top, 7.4″ Bottom) (203413) . . . . . . . . . . . . . . . . . . . . . . . 38 Belt and Sheave, 3/B BSL “D” (6.8″ Top, 8″ Bottom) (203414) . . . . . . . . . . . . . . . . . . . . . . . . . 39 Belt and Sheave, 3/B BSL “E” (6.2″ Top, 8.6″ Bottom) (206351) . . . . . . . . . . . . . . . . . . . . . . . 40 Rotor Assembly with Shankless Tooth; 51″ (203124), 61″ (203252) . . . . . . . . . . . . . . . . . . . . . 42 Rotor with Shankless Tooth; 51″ (203123), 61″ (203251) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Rotor Assembly with Planer Teeth; 51″ (203530), 61″ (203532) . . . . . . . . . . . . . . . . . . . . . . . . 44 Rotor with Planer Teeth; 51″ (203529), 61″ (203531). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Motor Assembly; 51″ (209025), 61″ (209026) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Overhung Load Adapter (N16416). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Right Hand Hose Kit (208093) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Machine Decals and Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Appendix
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Inches Hardware and Lock Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Metric Hardware and Lock Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Battle Ax Light – Skid Loader OM

Ordering Code
Ordering Code
Battle Ax Light – Skid Loader (Example)
The ordering code will consist of two numbers (machine size), three letters (machine type), one letter (cutter type), two numbers (motor system), one letter (sheaves and belt combination), and one letter (options). An example for a Battle Ax Light – Skid Loader of this type would be as shown below.
51BSLQ60A.P
SIZE
51 = 51″ Cut 61 = 61″ Cut
TYPE
BSL = Battle Ax Skid Loader Light
TOOTH
Q = Shankless P = Planer
MOTOR SYSTEM
60 = 45cc
SHEAVES/BELT COMBO
A = 8.6″ Top, 6.2″ Bottom B = 8.0″ Top, 6.8″ Bottom C = 7.4″ Top, 7.4″ Bottom D = 6.8″ Top, 8.0″ Bottom E = 6.2″ Top, 8.6″ Bottom
PUSHER BAR
P = Pusher Bar R = Right Hand Hose

Battle Ax Light – Skid Loader OM

1

2

Battle Ax Light – Skid Loader OM

Introduction

Owner Information
Thank you for your decision to purchase a Battle Ax Light skid loader-mounted shredder from Loftness. To ensure maximum performance of your machine, it is mandatory that you thoroughly study the owner’s manual and follow its recommendations. Proper operation and maintenance are essential to prevent injury or damage and to maximize machine life.
The Loftness Battle Ax Light is an effective, reliable machine used for maintaining grass, weeds, brush and trees. Efficiently cuts and mulches up to 6″ diameter material. Intermittently cuts larger diameter material. Lifting or tilting the Battle Ax Light increases the risk of flying debris. Because of the high speed of the teeth, the life of the teeth will be reduced if it is operated in rocky terrain or in areas where many obstacles are present. Areas to be mowed should be free of debris such as rocks, bottles, etc. The teeth cut and pulverize the grass, weeds, and brush. The Battle Ax Light deposits cut material over the entire width-of-cut, which eliminates bunching or windrowing behind the machine.
Operate and maintain this machine in a safe manner and in accordance with all applicable local, state, and federal codes, regulations and/or laws, and in compliance with on-product labeling and these instructions.
Make sure that all personnel have read this owner’s manual and thoroughly understand safe and correct operating, installation and maintenance procedures.
Continuous improvement and advancement of Loftness products may result in changes to your equipment that may not be reflected in this publication. Loftness reserves the right to make product improvements to the machine at any time. Although great care has been taken to ensure the accuracy of this publication, Loftness does not assume any liability for errors or omissions.
Warranty Policy
Be sure to read and understand the Warranty Policy at the beginning of this manual. It is also important that you fill out the Warranty Registration form(s) completely with your dealer so as not to void the warranty.

Serial Number Location
1
2
The machine serial number is shown in the tag (1), and is also stamped into the frame (2) on the skid steer mounting bracket. Always use your model and serial number when requesting information or when ordering parts.

Battle Ax Light – Skid Loader OM

3

Introduction

Manual Storage

3

2

1
2
Keep the owner’s manual and the entire documentation packet in the manual holder (1) provided on your Battle Ax Light. The owner’s manual must be available for all operators. To access the manual holder, remove the six bolts (2) and lift the cover (3) off.

Battle Ax Light Features
· Downward Rotation Design · Premium Strength Steel Body & Rotor · Front Mounted · Hydraulic Driven · Universal Skid-Loader Mount · Adjustable Tree Pusher – (Optional) · Claw Hooks On Tree Pusher · Two-stage Cutting Chamber – uses 2 shear bars,
producing a finer mulch with less passes · Power Requirement – 15-35 GPM up to 4100 PSI –
30-70 hydraulic horsepower · Pressure Gauge · Fixed Displacement Gear Motor – 45cc · Rotor Speed 1750-2275 RPM · 13.5 in. (34 cm) Diameter Rotor. · Efficient Staggered/Spiral Tooth Pattern · Shankless or Planer Teeth (sharpenable) · 1.75 in. (44.5 mm) Piloted Double Taper Roller
Bearings. · Anti Wrap Bearing Protection · Heavy Duty Bearing Block · 3-Band V-Belt · Tapered-Lock Sheaves · Skid Shoes · Steel Chain Deflectors · Adjustable Shear Bar · Built-in depth gauges – controls cutting depth. · Hydraulic Hoses

4

Battle Ax Light – Skid Loader OM

Safety Instructions

Safety First

Safety Alert Symbol
This message alert symbol identifies important safety messages on the machine and in the owner’s manual. When you see this symbol, be alert to the possibility of personal injury and carefully read the message that follows.

In the owner’s manual and on decals used on the machine the words DANGER, WARNING, CAUTION, IMPORTANT, and NOTE are used to indicate the following:

DANGER: This word warns of immediate hazards which, if not avoided, will result in severe personal injury or death. The color associated with Danger is RED.

WARNING: This word refers to a potentially hazardous situation which, if not avoided, could result in severe personal injury or death. The color associated with Warning is ORANGE.

CAUTION: This word refers to a potentially hazardous or unsafe situation that, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. The color associated with Caution is YELLOW.

IMPORTANT: Highlights information that must be heeded.

NOTE: A reminder of other related information that needs to be considered.

If Safety Decals on this machine are ISO two panel pictorial, decals are defined as follows:

· The first panel indicates the nature of the hazard.

· The second panel indicates the appropriate avoidance of the hazard.

· Background color is YELLOW.

· Prohibition symbols such as are RED.

and STOP if used,

Be certain all machine operators are aware of the dangers indicated by safety decals applied to the machine, and be certain they follow all safety decal instructions. Contact Loftness for safety decal replacement.
Loftness cannot anticipate every possible circumstance that may involve a potential hazard. The warnings in this owner’s manual are not all inclusive.
Owner’s Responsibility
Due to the potential danger of flying debris, it is the owner’s responsibility and is “ABSOLUTELY MANDATORY that IMPACT-RESISTANT SHIELDING” be installed on the machine to protect the operator.
It is ABSOLUTELY MANDATORY that all personnel read and follow all safety precautions before operating the machine and attachment.
Make sure that all personnel have read this owner’s manual, and thoroughly understand safe and correct installation, operation, and maintenance procedures.
Operate and maintain this machine in a safe manner and in accordance with all applicable local, state, and federal codes, regulations and/or laws; and in compliance with on-product labeling and this owner’s manual instructions.
Make sure that all personnel know how to stop the machine and attachment by disengaging all controls. See “Mandatory Shut-Down Procedure” on page 5.
Make sure the attachment is installed on the machine correctly before being placed into service. At regular intervals thereafter, the attachment should be serviced in accordance with procedures outlined in this owner’s manual.
Mandatory Shut-Down Procedure
· Stop the machine and attachment on a level surface and lower the attachment to the ground.
· Move throttle to idle position.
· Disengage all power to the attachment.
· Shut off engine and remove the key.
Wait until the rotor has stopped completely before inspecting the attachment.

Battle Ax Light – Skid Loader OM

5

Safety Instructions

Safety Rules
These are general safety considerations. Additional precautions may be necessary to operate your machine in a safe manner. Be certain you are operating your machine in accordance with all safety codes, OSHA rules and regulations, insurance requirements and local, state, and federal laws.
· Read and observe all warnings decals on the machine before attempting to operate the attachment. Do not attempt to operate this attachment unless all factory devices and decals are in place. Keep safety decals clean of dirt and grime. Keep all guards, shields and decals in place.
· Remove from area of operation all foreign objects such as bottles, rocks, wire, etc., that might become tangled in the rotor, causing damage to the machine or be thrown striking other objects.
· Do not allow any people and animals within 300 feet of the machine and attachment during operation.
· Do not allow anyone to operate the attachment until he or she has read the owner’s manual and is completely familiar with all safety precautions. Keep the work area clear of all unauthorized personnel.
· Do not allow persons under the influence of alcohol, medications, or other drugs that can impair judgment or cause drowsiness to operate or maintain the machine.
· Always use an approved roll bar and seat belt for safe operation. Overturning a machine without a roll bar and seat belt can result in injury or death.
· Use the handholds and step plates when getting on and off the machine to prevent falls. Keep steps and platform cleared of mud and debris.
· Always have an operator in the machine while the attachment is in operation. Never leave the machine and attachment running and unattended.
· Operate the attachment only from the operator’s seat.
· Keep your feet on the pedals, (floor plates) seat belt fastened snuggly and seat bar lowered, (if equipped), when operating the attachment.

· The adjustable push bar could contact the machine in some positions. Before starting the power unit, set the push bar in the most forward position, then slowly rotate the attachment back while an assistant checks for clearance. Repeat this process in the other settings to determine which positions are usable with your machine.
· Never attempt to make any adjustments while the attachment is running or the key is in the “ON” position in the machine. Before leaving the operator’s position, disengage power to the attachment, shut off engine and remove ignition key.
· Disengage auxiliary hydraulics and place all machine controls in neutral and engage the parking brake before starting the engine.
· Become familiar with and know how to operate all safety devices and controls on the machine and attachment before attempting to operate. Know how to stop the machine and attachment before starting it.
· Repeated impact of the knives with hard objects can cause excessive wear and damage to the skid-loader or attachment. Be sure to maintain recommended ground clearance as specified in this manual.
· Should excessive vibration occur, disengage the auxiliary hydraulics immediately and shut off engine. Do not continue to operate the attachment until the problem has been determined and corrected.
· Do not start, operate, or work on this attachment until you have carefully read and thoroughly understand the contents of this manual and the operator’s manual for your machine.
· Keep children, bystanders and other workers off and away from the machine and attachment during operation. No riders allowed.
· Before inspecting, cleaning, lubricating, adjusting or servicing any part of the attachment, always exercise the Mandatory Shut-Down Procedure. See “Mandatory Shut-Down Procedure” on page 5. After service has been performed, be sure to restore all guards, shields and covers to their original position.
· Make sure the operator’s area is clear of any distracting objects. Keep work areas clean and free of grease and oil to avoid slipping or falling.

6

Battle Ax Light – Skid Loader OM

Safety Instructions

Safety Rules (Cont’d)
· Make sure all controls, (levers, pedals and switches), are in NEUTRAL position before starting the engine.
· Before leaving the operator’s position for ANY reason or allowing anyone to approach the machine and attachment, always perform the mandatory shutdown procedure.
· Do not wear loose hanging clothes, neckties or jewelry around rotating parts. Long hair is to be placed under a cap or hat. These precautions will help prevent you from becoming caught in any moving parts on the machine and attachment.
· Before working under the attachment, be certain it is securely blocked!
· Do wear safety glasses, ear protection, respirators, gloves, hard hats, safety shoes and other protective clothing when required.
· Periodically check all guards, shields and structural members. Replace or repair anything that could cause a potential hazard.
· Do not replace components or parts with other than factory-recommended service parts. To do so may decrease the effectiveness of the machine.
· It is the operator’s responsibility to be aware of machine and attachment operation and work area hazards at all times.
· Never operate the attachment without adequate light and visibility.
· Keep hands and feet clear! Never step over or climb over the attachment while the rotor is engaged or the engine is running; entanglement could occur.
· Operators are responsible to know the location and function of all guards and shields including but not limited to belt drives and rotor. Operators are responsible to make certain that all guards are in place when operating the machine and attachment.
· Operators are responsible to be aware of safety hazard areas and follow instructions on warning, caution, or danger decals applied to the machine.
· Know the area before operating the machine. Be aware of power lines or other equipment.

· Do not lubricate parts while the machine is running.
· Do not smoke while servicing the machine.
Hydraulic Safety
· The hydraulic system is under high pressure. Make sure all lines and fittings are tight and in good condition. These fluids escaping under high pressure can have sufficient force to penetrate skin and cause serious injury.
· Never check for leaks by using any part of your body to feel for escaping fluid.
WARNING: Contact with high pressure fluids may cause fluid penetration and burn hazards. Fluid that is under pressure can penetrate body tissue. Fluid penetration can cause serious injury and possible death. If fluid is injected into the skin, seek medical attention immediately!
California Proposition 65 Warning
WARNING: This product can expose you to Mineral Oil, which is known to the State of California to cause cancer. For more information, go to www.p65warnings.ca.gov.
A decal with this warning statement is adhered to the machine. If the decal should become worn or missing, replace immediately.

Battle Ax Light – Skid Loader OM

7

Safety Instructions

Safety Decal Locations
Check and replace any worn, torn, hard to read, or missing safety decals on your machine.
NOTE: This section shows where safety-related decals are applied on the machine. For all machine decals see “Machine Decals and Signs” on page 50.

1
Rear View

1

2 4

5

7

3 8

3 6

Top View
9
1 10
8

11

10

Note: Pusher bar and hydraulic hoses removed on top view and side view for clarity.
1 12
3

Right Side View (belt cover removed)

Front View

Left Side View

See the following page for detailed images of the safety decals called out above.

8

Battle Ax Light – Skid Loader OM

Safety Decal Locations (Cont’d)
1 Part No. N29769
2
Part No. N17014 3
Part No. N28386 4
Part No. 203264 5
Part No. 200491 6
Part No. N20661 Battle Ax Light – Skid Loader OM

Safety Instructions
7
Part No. N68724 8
Part No. N68716 9
Part No. N17013 10
Part No. 4334 11
Part No. N28385 12
Part No. 4256 9

Safety Instructions
Battle Ax Light Identification
Pusher Bar

Manual Holder (behind cover)

Hydraulic Motor (behind cover)

Rotor Pressure Gauge

Cutting Teeth

Rotor Bearing Guard
Skid (left side)

Hydraulic Hoses 10

Mounting Plate Deflector Chains

Drive Belt Cover
Drive Belt (behind cover)

Step

Skid (right side)

Battle Ax Light – Skid Loader OM

Set-up Instructions

Pusher Bar Assembly
The Battle Ax Light is shipped with the pusher bar in an upright position. For shipping purposes, the left side and right side pusher tubes are reversed and some reconfiguring is required. Follow the procedure below to get the mulcher into an operating position.

from the 25-7/8 in. pusher tube (6) attached to the left side of the machine.
Remove the nut (7), lock washer (8), and bolt (9) securing the pusher tube to the machine frame.
NOTE: This 25-7/8 in. tube will be moved to the right side of the frame in a later step.
Remove the 37-1/2 in. pusher tube (10) from the right side of the machine by removing the upper nut (11), lock washer (12), and bolt (13).
Remove lower nut (14), lock washer (15), and bolt (16).
NOTE: This 37-1/2 in. tube will be moved to the left side of the frame.

CBA 1

The pusher bar can be set into one of three different operating positions as shown above. Determine which of the three positions is desired before assembling.

2 345

1 11 12 13
10 6

789

14 15 16

NOTE: Assembling the pusher bar requires two people or the use of an approved lifting device (1) to support the push bar as it is being adjusted.
Ensure pusher bar (2) is being safely supported.
Remove the upper nut (3), lock washer (4), and bolt (5)

5
234
678
Align the top end hole of the 37-1/2 in. pusher tube (1) into the desired position hole (A, B, or C) on the left side pusher bar side plate. (Position A is shown in the image above.) Insert the bolt (2) from the outside and install the lock washer (3) and nut (4) onto the bolt on the opposite side of the pusher tube. Do not tighten at this time. Align the bottom end hole of the pusher tube with the hole (5) in the left side of the mulcher frame. Insert the bolt (6) from the outside and install the lock washer (7) and nut (8) onto the bolt on the opposite side of the pusher tube. Do not tighten at this time.
(Procedure continued on following page.)

Battle Ax Light – Skid Loader OM

11

Set-up Instructions
Pusher Bar Assembly (Cont’d)

1 5

ABC 432

NOTE: Do not discard the shipping stand. It is used to stabilize the Battle Ax during storage. Keep in a secure location until ready to store.
Installing the Battle Ax Light to the Loader
Fully raise the attachment-locking levers on the loader mounting plate.
1

876

Align the top end hole of the 25-7/8 in. pusher tube (1) onto the right side pusher bar side plate, using the same position hole (A, B, or C) as the left side. Insert the bolt (2) from the outside. Install the lock washer (3) and nut (4) onto the bolt on the opposite side of the pusher tube. Align the bottom end of the pusher tube with the hole (5) in the right side of the mulcher frame. Insert the bolt (6) from the outside and install lock washer (7), and nut (8) onto the bolt on the opposite side of the pusher tube. Tighten all hardware on the both the left side and right side pusher tubes.
Remove Shipping Stand
1
A stand (1) is secured to the Battle Ax to keep it stable during shipping. This can be removed after the pusher bar has been moved to the operating position.

Tilt the loader mounting plate ahead. Drive forward with the loader and hook the top edge of the loader mounting plate under the top flange (1) on the Battle Ax Light mounting plate. Be careful not to damage the locking levers on the loader mounting plate.
Tilt the loader mounting plate back until the mulcher mounting plate is firmly against the loader mounting plate, but Do Not lift the attachment off the ground.
WARNING: Before you leave the operator’s seat: Lower the lift arms, put the attachment on the ground. Stop engine and remove ignition key. Engage the parking brake.
Fully lower the attachment-locking levers on the loader mounting plate.
WARNING: Locking-wedge pins must extend through the holes in attachmentmounting plate. Levers must be fully down in the locked over-center position. Failure to secure wedge pins can allow attachment to come off, causing serious injury or death.
(Procedure continued on following page.)

12

Battle Ax Light – Skid Loader OM

Installing the Battle Ax Light to the Loader (Cont’d)
Hydraulic Connections
WARNING: Hydraulic Lines. Protect hands and body from high pressure fluids. Pressurized fluids can penetrate the skin. Disconnect and lock out power source before disconnecting and/or connecting hydraulic hoses.
1

Set-up Instructions
1 Raise the Battle Ax Light off the ground and place blocks (1) underneath the skids. Lower the Battle Ax Light down on the blocks.

NOTE: The hydraulic hose quick couplers shown above are not supplied with the Battle Ax Light.
Install the Battle Ax Light quick couplers to the loader.
NOTE: The case drain quick coupler (1) of the Battle Ax Light must be connected to the loader’s auxiliary hydraulic system for proper operation of the Battle Ax Light.
IMPORTANT: It is the owner’s responsibility to assure that the hydraulic hoses from the power unit to the attachment are not caught in pinch points, or in any way damaged by moving parts.
Checking Rotor Rotation
DANGER: Keep hands, feet, and clothing clear of rotor and bearings while the loader is running.

Rotor Rotation
Engage the loader auxiliary hydraulics, the rotor should start rotating in a forward direction. The rotation should be counterclockwise as viewed from the left side of the Battle Ax Light. NOTE: If the rotor is rotating backward, reverse the
quick couplers (not supplied) on the Battle Ax Light hydraulic hoses. Re- install the couplers (not supplied) on the loader and test for correct rotor rotation.
WARNING: The Battle Ax Light can be damaged if rotor is operated in reverse rotation.

Battle Ax Light – Skid Loader OM

13

Set-up Instructions

Checking Rotor Speed
DANGER: Shut down power from the loader before removing the belt cover and applying reflective tape to the sheave. Keep the Battle Ax Light skids on blocks for this procedure.

Cutter Bar Adjustment
4

2

1 2
Remove the belt cover. See “Removing Belt Cover” on page 19 for instructions. Apply a small piece of reflective tape (1) to the outer edge of the lower sheave. Start the loader and engage the auxiliary hydraulics.
DANGER: Keep hands, feet, and clothing clear of the rotor, belt, and sheaves while the loader is running.
Point an electronic (photo) tachometer (2) towards the edge of the sheave to check the rotor speed. NOTE: The tachometer is not supplied with the Battle
Ax Light. Test the rotor RPM with the loader engine at full throttle. Shut down the loader when done. See “Motor & Sheave Selection Chart” on page 24 for rotor RPM. If it is outside this recommended range, it may be necessary to disconnect the Battle Ax Light and test the hydraulic output of the loader with a flow meter to see if it corresponds with the factory specifications. Turn power off from loader and return the belt cover to position, securing with the eight bolts.

1
3
NOTE: The cutter bar can be adjusted back or forward to increase or decrease the distance between the bar and the rotor. Most operators find the best performance is achieved by adjusting the cutter bar as close as the slots will allow (approximately a 1/4″ gap from knife to cutter bar). A wider gap generally increases finished partical size and horsepower requirements.
WARNING: Shut down and disconnect the hydraulic hoses from the loader before adjusting the cutter bar.
Loosen the series of bolts (1) with washers (2) securing the cutter bar (3) to the frame. Move the cutter bar either forward or back making sure the distance moved is consistent through the entire length of the cutter bar. Retighten bolts.
Over time, the cutter bar edge will become worn and rounded from use. There are a total of 4 wear edges available by removing and flipping the bar, side to side and front to back.
CAUTION: If adjusting the cutter bar after the machine has been used, the cutter bar should be completely removed to clear any debris away from contact surfaces before assembly and tightening. FAILURE TO DO SO COULD RESULT IN SEVERE DAMAGE TO THE MACHINE!.

14

Battle Ax Light – Skid Loader OM

Operating Instructions

Getting Started
Visually inspect the unit before starting the machine up. Check for loose or missing parts. Check all bolts for tightness.
For best results, the areas to be mowed should be free of debris such as bottles, metal objects, rocks, wire, etc. The teeth cut and pulverize the brush, grass and weeds.
For first-time users, start the machine in a clear, open area and become familiar with the controls. Run throttle at half speed and travel at a low speed. Raise the mulching head only slightly until comfortable the machine.
WARNING: Due to the potential danger of flying debris, it is the owner’s responsibility and is “ABSOLUTELY MANDATORY that IMPACT-RESISTANT SHIELDING” be installed on the machine to protect the operator.
WARNING: Lifting or tilting the Battle Ax Light increases the risk of flying debris.
DANGER: Keep hands and feet out! Do not step on or climb over the unit while machine is in operation, or engine is running. Do not carry passengers.
WARNING: Do not operate the attachment above the rated RPM. Check with your Loftness dealer to be sure your attachment is set-up with the correct hydraulic motor to match the hydraulic flow GPM (Gallons Per Minute) of your machine.
WARNING: Flying debris can gather on the loader and needs to be cleaned off, especially around the radiator, oil cooler screens, engine compartment, and exhaust areas. Periodic cleaning will help prevent the possibility of fire.
DANGER: DO NOT allow ANY people or animals within 300 feet of the work area while operating this machine.

Operation
WARNING: Always stop engine and remove key before leaving operators seat.
Tilt attachment mounting frame back and raise the Battle Ax Light slightly above the ground when moving the machine. Lower mulching head so skids are on ground. Set engine speed to low idle and engage the mulching head. Slowly increase engine speed to high idle. Move the loader and Battle Ax Light forward and begin mowing. NOTE: Various mowing conditions, and desired finished
cut appearance, will determine proper ground speed. Operating Tips To reduce rotor jams, approach brush and trees at a slow speed. When operating the mulching head near the ground, keep as low to the ground as possible without the teeth striking ground or other obstructions. NOTE: Because of the high speed of the rotor, the life of the teeth will be reduced if it is operated in rocky terrain or in areas where many obstacles are present.

Battle Ax Light – Skid Loader OM

15

Operating Instructions

Clearing Jams
If the rotor stalls, or gets jammed with debris, stop rotor and raise slightly. Start rotor again to free debris
WARNING: Do not attempt to dislodge jams by hand while the loader is running. Shut down and lock out power from the loader before attempting to remove debris by hand.
Log Moving

Detaching Battle Ax Light
Park the loader on a dry level surface. Place blocks underneath the skids if necessary.
Lower the Battle Ax Light to the ground.
Shut off engine and remove key.
Make sure the rotor has stopped completely before continuing.
Disconnect hydraulic hoses and coil neatly on top of the Battle Ax Light.
Detach the loader from the mounting plate.
WARNING: Do not attempt to detach the Battle Ax Light while the loader is running. Shut down and lock out power from the loader before detaching.

Disengage hydraulic power to rotor before moving logs and brush with pusher bars.
Raise the loader lift arms and tilt the Battle Ax Light forward until the push bar extensions are over the log or item being moved. Lower the lift arms and position the log between push bar extensions and the Battle Ax Light. Move the loader backwards, dragging the log to the desired location.

16

Battle Ax Light – Skid Loader OM

Maintenance

General Maintenance

To ensure efficient operation, you should inspect, lubricate, and make necessary adjustments and repairs at regular intervals. Parts that are starting to show wear should be ordered ahead of time, before a costly breakdown occurs and you have to wait for replacement parts. Keep good maintenance records, and adequately clean your Battle Ax Light after each use.
Proper lubrication is important. Too little lubricant will cause premature failure of a bearing. Too much lubrication usually causes high operating temperature and early failure of seals. Follow all lubrication instructions and schedules included in this section.

Maintenance Schedule

H

O

U

SERVICE POINTS

R

S

Machine Loose Bolts Every Hoses and Wiring 8 Oil Leaks Rotor Bearing Teeth

Every 100

Belt Tension Drive Belt Safety Labels

Hydraulic Motor Every 500 Overhung Load
Adapter

SERVICE REQUIRED

C H E C K

C L E A N

C H A N G E

G R E A S E

A D J U S T

O I L

X
X X
X

X X

X X X

X

X

X

Lubrication
Grease Points Location
Use a #2 general purpose lithium based grease unless noted otherwise. NOTE: Replace any broken or missing grease fittings.
Be sure to clean fittings before greasing.
NOTE: Lubricate the grease point every “X” hours indicated on the decal adjacent to the grease point.
See “Battle Ax Light Identification” on page 10 for component location and identification.
1

Battle Ax Light – Skid Loader OM

Location: Left side rotor bearing (1). Interval: Every 8 hours of operation.
NOTE: Rotor bearings cannot be damaged by overgreasing. Lubricate the fittings until a small amount of grease is purged from the bearing.
17

Maintenance
Lubrication (Cont’d)
Grease Points Location (Cont’d)

Overhung Load Adapter
The motor must be removed to access the overhung load adapter. Refer to “Removing Motor Cover” on page 20 for instructions.

2 1

Location: Right side rotor bearing (2). Interval: Every 8 hours of operation.

NOTE: Rotor bearings cannot be damaged by over-

2

greasing. Lubricate the fittings until a small

amount of grease is purged from the bearing.

Remove the plug from the port (1) located on the top of the overhung load adapter, and the plug from the lower port (2) located on the back side.
Partially tilt the Battle Ax Light back towards the skid steer to drain the hydraulic oil.
Reinsert the lower plug and tighten.
Using a funnel placed into the top port of the overhung load adapter, add 4 oz. of universal hydraulic fluid.
Return the plug back into the top port and tighten.
NOTE: If replacing bearings or seals in the overhung load adapter, be certain to refill with hydraulic fluid after reassembly.

18

Battle Ax Light – Skid Loader OM

Removing Belt Cover
DANGER: Shut down power from the loader before removing the belt cover. Failure to do so could result in serious injury or death.

Maintenance
Removing Left End Bearing Cover
DANGER: Shut down power from the loader before removing the bearing cover. Failure to do so could result in serious injury or death.

2

2

1

2

2

2

2

2

2

2

2

1

To remove the belt cover (1), unscrew the six bolts (2) and lift the cover off of the frame.
CAUTION: The belt cover is heavy. Support the cover when removing.
When maintenance/repairs are complete, return the cover back into position and tighten and secure all bolts.

To remove the left side bearing cover (1), unscrew the four bolts (2) and lift the cover off of the frame.
When maintenance/repairs are complete, return the cover back into position and tighten and secure all bolts.

Battle Ax Light – Skid Loader OM

19

Maintenance
Removing Motor Cover
DANGER: Shut down power from the loader before removing the motor cover. Failure to do so could result in serious injury or death.

2 1

1

1

Removing Hose Cover
DANGER: Shut down power from the loader before removing the hose cover. Failure to do so could result in serious injury or death.
Remove the motor cover. Refer to “Removing Motor Cover” on this page for instructions.

12 1

1

1

1

1

1

1

2

Note: 51″ model shown.

3 3 3
Remove the 3 bolts (1) on the rear of the motor cover (2) followed by the three bolts (3) on the front.
Carefully lift the cover off of the frame, being cautious not to pinch or damage the pressure gauge hose under the motor cover.
NOTE: The manual holder is secured to the underside of motor cover.

Remove the eight bolts (1) securing the hose cover (2) and lift the cover from the machine.
When maintenance/repairs are complete, return the covers back into position by reversing the procedures above. Be sure to tighten and secure all bolts.

20

Battle Ax Light – Skid Loader OM

Skid Removal/Replacement
WARNING: Shut down and lock out power from the loader before removing skids. Failure to do so could result in serious injury or death.

Note: Left side skid is shown. The procedure is identical for both sides.

12

12

Maintenance
Belt Adjustment
WARNING: Shut down and lock out power from the loader before adjusting the drive belt. Failure to do so could result in serious injury or death.
Remove the belt cover and motor cover. Refer to “Removing Belt Cover” on page 19, and “Removing Motor Cover” on page 20 for instructions.
1

12

12 3

Lift the Battle Ax Light off of the ground about 6 inches. Place blocks under the rotor (not under teeth) to support the Battle Ax Light when lowered. Do not place blocks under the skids.
Remove nuts (1) and slide carriage bolts (2) out. Lower the skid (3) and remove.
To install a new or repaired skid, align holes in skid with holes on frame. Re-install the bolts, add the nuts and tighten securely against the skid.

Loosen the four overhung load adapter support nuts (1) on the motor mount bracket.

2 3

1/2 in.

3/8 in.

Battle Ax Light – Skid Loader OM

Loosen the jam nut (2). Then turn the hex bolt (3) to either increase or decrease belt tension. Belt should move no more than 1/2 in. (12.7 mm) to the left, and no more than 3/8 in. (9.53 mm) to the right when pressure applied at the midpoint.
Retighten the jam nut (2).
Retighten overhung load adapter support bolts.
21

Maintenance
Tooth Removal and Installation
DANGER: Shut down and lock out power from the loader before removing teeth. Failure to do so could result in serious injury or death.
12

3
Note: Shankless tooth style shown.
Remove the bolt (1), washer (2), and tooth (3). Use copper based anti-seize when reinstalling the bolts. Torque to 200 ft.-lbs. IMPORTANT: When a damaged tooth is replaced, the
tooth directly opposite (180 degrees) must be replaced at the same time to retain balance.
Tooth Sharpening
NOTE: The teeth need to be kept sharp to maintain the most effective operation of the attachment. Daily inspection and touch up is recommended.
NOTE: The teeth can either be removed from the attachment or remain installed for sharpening.
WARNING: Rotor must be stabilized to prevent accidental rotation any time the rotor is exposed for service work.

NOTE: The cutter teeth have been heat treated to a specific hardness. Care must be taken to avoid overheating the leading edge of the tooth while sharpening. If the coloring in the tooth changes to either a blue or brown during the sharpening, you have removed the temper and the tooth will not hold it’s cutting edge.
NOTE: When re-sharpening teeth using machine shop equipment, avoid overheating the teeth by using a flood coolant system.
NOTE: When re-sharpening teeth using a hand grinder, avoid overheating the tooth by lightly grinding each tooth, moving across the entire row of teeth before returning to the first tooth to repeat the procedure.
NOTE: Sharpen each tooth equally to maintain rotor balance. Always return tooth to it’s original location if it is removed from the rotor for sharpening.
(Procedure continued on following page.)

22

Battle Ax Light – Skid Loader OM

Maintenance

Tooth Sharpening (Cont’d)
NOTE: It is not necessary to match the factory angle on the underside of the cutting edge when resharpening. Sharpen each tooth at a slight angle for each successive sharpening (represented by the dashed lines shown in the illustration above). When the cutting edge of the tooth is 1-1/8 in. from the back side of the tooth, the tooth must be replaced.

Storage
End of Season
· Clean entire Battle Ax Light thoroughly.
· Clean belt and sheaves, relax the belt tension. See “Belt Adjustment” on page 21.
· Lubricate all parts of the machine. See “Lubrication” on page 17.
· Make a list of all worn or damaged parts and replace them.
· Paint all parts that are worn or rusted.
· Store Battle Ax Light in a clean, dry area.
· Secure hoses on machine to avoid damage.
· Review the Battle Ax Light operator’s manual.
Beginning of the Season
· Review the Battle Ax Light operator’s manual.
· Lubricate all parts of the machine. See “Lubrication” on page 17.
· Tighten all bolts, nuts, and set screws. See “Torque Specifications” on page 55.
· Adjust belt tension. See “Belt Adjustment” on page 21.
· Replace all damaged, worn or missing decals.
· Install the Battle Ax Light on an loader and test for proper operation.
WARNING: DO NOT allow ANY people or animals within 300 feet of the work area while operating this machine.

Battle Ax Light – Skid Loader OM

23

Maintenance

Motor & Sheave Selection Chart

GPM

MOTOR RPM

15

1262

16

1346

17

1430

18

1514

19

1598

20

1682

21

1767

22

1851

23

1935

24

2019

25

2103

26

2187

27

2271

28

2355

29

2439

30

2524

31

2608

32

2692

33

2776

34

2860

35

2944

DISPLACEMENT
45cc (2.75ci)

LOFTNESS PART
NUMBER
208178

ROTOR RPM
1751 1867 1984 2100 2217 1979 2079 2178 2276 2019 2103 2187 2271 2002 2073 2145 2217 1941 2001 2062 2122

TOP SHEAVE (LOFTNESS NUMBER) BOTTOM SHEAVE ( LOFTNESS NUMBER)
BELT LENGTH (LOFTNESS NUMBER)
Top Sheave 8.6″ N16134 1.5″ Taperlock 8126
Bottom Sheave 6.2″ N34043 1.75″ Taperlock 8127 Belt 203410 Model Code “A”
Top Sheave 8.0″ N17045 1.5″ Taperlock 8126
Bottom Sheave 6.8″ N11421 1.75″ Taperlock 8127 Belt 203410 Model Code “B”
Top Sheave 7.4″ N34689 1.5″ Taperlock 8126
Bottom Sheave 7.4″ N34689 1.75″ Taperlock 8127 Belt 203410 Model Code “C”
Top Sheave 6.8″ N11421 1.5″ Taperlock 8126
Bottom Sheave 8.0″ N17045 1.75″ Taperlock 8127 Belt 203410 Model Code “D”
Top Sheave 6.2″ N34043 1.5″ Taperlock 8126
Bottom Sheave 8.6″ N16134 1.75″ Taperlock 8127 Belt 203410 Model Code “E”

24

Battle Ax Light – Skid Loader OM

Troubleshooting
PROBLEM Excessive Vibration
Uneven Cutting Rotor Will Not Turn

Maintenance

CAUSE

SOLUTION

Broken or missing teeth.

Replace teeth.

Mud and/or debris wrapped around the rotor.
Faulty drive line bearing.

Clean the Battle Ax Light. Replace bearing(s).

Faulty rotor bearing.

Replace bearing(s).

Damage to rotor (includes bent end of shafts, missing balance weights, or actual rotor deformity from striking rocks, etc.)
Teeth dull or worn excessively.

Consult factory. Replace teeth.

Engine RPM too slow.

Adjust machine RPM to full throttle.

Travel speed too fast.

Reduce ground speed.

Faulty drive line bearing.

Replace bearing(s).

Faulty rotor bearing.

Replace bearing(s).

Belt damaged.

Replace belt.

Belt slipping.

Clean or replace belt. Adjust tension.

Battle Ax Light – Skid Loader OM

25

26

Battle Ax Light – Skid Loader OM

Parts Identification

PARTS IDENTIFICATION

Battle Ax Light – Skid Loader OM

27

Parts Identification
Covers, Manual Holder
3 1*
2 8
7
2
2*

2 5 4
6 2

9

16 15
14 11

12 13

2*

10

8

** For parts breakdown of item 1, Motor Cover (203233), see page 34.

28

Battle Ax Light – Skid Loader OM

Covers, Manual Holder

QTY.

1

1

2

14

3

3

4

1

5

1

6

3

7

1

8

10

1 9
1

10

1

11

2

12

1

13

2

14

1

15

2

16

2

PART # 203233 N26743
4302 N19600 203417
4050 203541 N26748 203234 203258 203543 N47855 203106
4979 206411 N16470
4005

Parts Identification
DESCRIPTION MOTOR COVER ASSEM BOLT, 3/8″ X 1″ SER FLG BOLT, CARRIAGE 1/4″ X 3/4″ HOLDER, 01-315A STND.MANUAL MANUAL, BATTLE AX SKID LOADER LT
NUT, 1/4″ LOCK RH BEARING COVER BOLT, 1/2″ X 1″ SER FLG 51″ HOSE COVER ASSEM 61″ HOSE COVER ASSEM LH BEARING COVER BOLT, 3/8″ X 1-1/4″ SER FLG BA SHIPPING STAND ASSEM NUT, LOCK 3/8″ SER FLG MOUNT, BULKHEAD WASHER, 3/8 NORDLOCK BOLT, 3/8″ X 1-1/4″ GRADE 5

Battle Ax Light – Skid Loader OM

29

Parts Identification
Rotor, Skid Shoes

1

3

3

2

2 5
4*

  • For parts breakdown of item 4, Rotor Assembly, see page 42 for 51″ with Shankless Tooth (203124) and 61″ with Shankless Tooth (203252); see page 44 for 51″ with Planer Tooth (203530) and 61″ with Planer Tooth (203532).

1 2 3

4
5
30

QTY. 8 1 8 1 1 1 1 1

PART # 4055
203201 4383
203124 203252 203530 203532 203217

DESCRIPTION NUT, LOCK 5/8″ TOP BA SKID LIGHT RH SKID SHOE BOLT CARRIAGE, 5/8″ X 1-3/4″ ROTOR, 51″ BATTLE AX W/SHANKLESS ASSEM ROTOR, 61″ BATTLE AX W/SHANKLESS ASSEM ROTOR, 51″ BATTLE AX W/PLANER ASSEM ROTOR, 61″ BATTLE AX W/PLANER ASSEM BA SKID LIGHT LH SKID SHOE
Battle Ax Light – Skid Loader OM

Cutter Bar, Deflector Chains

Parts Identification

12 5
6 7

4
3 21

NOTE: Underside of Battle Ax Light shown.

QTY.

1

2

2

2

1 3
1

56 4
66

1 5
1

5 6
7

5 7
7

PART # 4375 4301
N49273 N49076
N15589
N49272 N49075
4494
4062

Battle Ax Light – Skid Loader OM

DESCRIPTION PIN, ROLL 3/16″ X 1″ WASHER, 7/16″ FLAT ROD, CARBIDE 51″ CHAIN ROD, CARBIDE 61″ CHAIN CHAIN, CARBIDE AX REAT (51″)
(61″) PLATE, RECUTTER 51″ PLATE, RECUTTER 61″ BOLT, 5/8IN X 2-1/4IN GR 8 FN TH (51″)
(61″) WASHER, 2″0D X 11/16″ID X 1/4T (51″)
(61″)
31

Parts Identification
Pusher Bar

1 3

4

5

2

6

1 2 3 4 5 6

32

QTY. 1 1 1 1 6 6 6

PART # 203156 203256 203236 203237 N64492
4166 4490

DESCRIPTION PUSHER, 51″ W/ DECALS PUSHER, 61″ W/ DECALS TUBE, PUSHER 37.5″ W/ BUSHING TUBE, PUSHER 25.8″ W/ BUSHING BOLT, 1-14 X 4″ GR. 8 FN. THR
WASHER, 1″ LOCK NUT, 1″-14UNF STANDARD
Battle Ax Light – Skid Loader OM

Motor Mount
12 5

Parts Identification
4 3

QTY.

1

4

2

4

3

4

4

1

5

1

PART # 4513 4486 4054
203168 N27483

Battle Ax Light – Skid Loader OM

DESCRIPTION BOLT, 1/2″ X 1-1/4″ GRADE 8
WASHER, 1/2″ FLAT NUT, LOCK 1/2″ TOP MOTOR MOUNT WLDMT BOLT, 1/2″ X 5″ GR 5 FL TH
33

Parts Identification
Motor Cover (203233)

3 2

5

4

6

7 8 9

Detail A

1

10 Detail A

1 2 3 4 5 6 7 8 9 10

34

QTY. 1 1 3 3 1 1 1 3 3 1

PART # 203232 205041 N16132 N16333 N16332 N16335 N16331 N16133 N16334 N16162

DESCRIPTION MOTOR COVER W/ DECALS GAUGE, 0-6000 PSI 4IN PRESS
BOLT, BHCS #8-32 X 1 BOLT, BHCS #10-32 X 1 FLANGE, MOUNT GAUGE FLANGE, MOUNT

10 FLANGE, MOUNT GAUGE #8 NUT, NYLON INSERT #8 NUT, NYLON INSERT #10 ELBOW,

1/4″ BLK 90 DEG STREET
Battle Ax Light – Skid Loader OM

Lubrication

Parts Identification

12

3

4 Right side rotor bearing lubrication.

3 2 1
4
Left side rotor bearing lubrication.

QTY.

1

2

2

2

3

2

4

2

PART # N17007 4304-10
4304 4471

Battle Ax Light – Skid Loader OM

DESCRIPTION GREASE ZERK, 1/8″ NPT BULKHEAD, FITTING-GREASE HOSE HOSE, GREASE 1/8″ X 15″ ELBOW, 1/8″ 45 DEG.STREET
35

Parts Identification
Belt and Sheave, 3/B BSL “A” (8.6″ Top, 6.2″ Bottom) (203411)

2

3

1

4

6
5 4

1 2 3 4 5 6

36

QTY. 1 1 1 2 1 1

PART # 203410 N16134
8126 7121-02
8127 N34043

DESCRIPTION BELT, 3/B 52″ SHEAVE, 3B X 8.6″ PD TAPERLOCK BUSHING, 1-1/2″ TAPERLOCK KEYED KEY, 3/8″ X 1-3/4″ BUSHING, 1-3/4 KW TAPERLOCK SHEAVE, 3B X 6.2 TPL 2517
Battle Ax Light – Skid Loader OM

Parts Identification
Belt and Sheave, 3/B BSL “B” (8″ Top, 6.8″ Bottom) (203412)

2

3

1

4

6
5 4

QTY.

1

1

2

1

3

1

4

2

5

1

6

1

PART # 203410 N17045
8126 7121-02
8127 N11421

Battle Ax Light – Skid Loader OM

DESCRIPTION BELT, 3/B 52″ SHEAVE, 3B X 8.0 TPL 2517 BUSHING, 1-1/2″ TAPERLOCK KEYED KEY, 3/8″ X 1-3/4″ BUSHING, 1-3/4 KW TAPERLOCK SHEAVE, TAPERLOCK 6.8 PD 3-BAND
37

Parts Identification
Belt and Sheave, 3/B BSL “C” (7.4″ Top, 7.4″ Bottom) (203413)
2 3
1 4
2 5 4

1 2 3 4 5

38

QTY. 1 2 1 2 1

PART # 203410 N34689
8126 7121-02
8127

DESCRIPTION BELT, 3/B 52″ SHEAVE, 3B X 7.4 TPL 2517 BUSHING, 1-1/2″ TAPERLOCK KEYED KEY, 3/8″ X 1-3/4″ BUSHING, 1-3/4 KW TAPERLOCK
Battle Ax Light – Skid Loader OM

Parts Identification
Belt and Sheave, 3/B BSL “D” (6.8″ Top, 8″ Bottom) (203414)

2

3

1

4

6
5 4

QTY.

1

1

2

1

3

1

4

2

5

1

6

1

PART # 203410 N11421
8126 7121-02
8127 N17045

Battle Ax Light – Skid Loader OM

DESCRIPTION BELT, 3/B 52″ SHEAVE, TAPERLOCK 6.8 PD 3-BAND BUSHING, 1-1/2″ TAPERLOCK KEYED KEY, 3/8″ X 1-3/4″ BUSHING, 1-3/4 KW TAPERLOCK SHEAVE, 3B X 8.0 TPL 2517
39

Parts Identification
Belt and Sheave, 3/B BSL “E” (6.2″ Top, 8.6″ Bottom) (206351)
1 2 3 4
6 5 4

1 2 3 4 5 6

40

QTY. 1 1 1 2 1 1

PART # 203410 N34043
8126 7121-02
8127 N16134

DESCRIPTION BELT, 3/B 52″ SHEAVE, 3B X 6.2 TPL 2517 BUSHING, 1-1/2″ TAPERLOCK KEYED KEY, 3/8″ X 1-3/4″ BUSHING, 1-3/4 KW TAPERLOCK SHEAVE, 3B X 8.6″ PD TAPERLOCK
Battle Ax Light – Skid Loader OM

Parts Identification

This page intentionally left blank.

Battle Ax Light – Skid Loader OM

41

Parts Identification
Rotor Assembly with Shankless Tooth; 51″ (203124), 61″ (203252)

12

6

7

3 45

54 32

8

11

9 7 6

10 12 3

  • For parts breakdown of item 8, 51″ Rotor (203123) and 61″ Rotor (203251), see page 43.

1 2 3 4 5 6 7

8
9 10 11 12
42

QTY. 8 8 2 10 10 2 2 1 1 1 1 1 1

PART # 201358 N16471 201356
4494 N16473 203132 201357 203123 203251 201359
4075 4076 4468

DESCRIPTION BOLT, 7/16″ X 2″ GR 8 FN TH WASHER, 7/16 NORDLOCK BEARING, 1-3/4″ PILOT ROLLER
BOLT,5/8-18 X 2-1/4 GR 8 WASHER, 5/8 NORDLOCK MOUNT, BEARING WELDMENT ANTIWRAP, 1 PIECE CARBIDE 8″ ROTOR, 51″ BATTLE AX W/SHANKLESS TOOTH ROTOR, 61″ BATTLE AX W/SHANKLESS TOOTH BUSHING, 1-3/4″ID X 2-1/4″OD
WASHER, 2-5/8″ OD WASHER, 1/2″ EXT CNTSK LOCK BOLT, 1/2-20UNF X 1-1/4 FL HD
Battle Ax Light – Skid Loader OM

Parts Identification
Rotor with Shankless Tooth; 51″ (203123), 61″ (203251)

1

QTY.

1 1
1

32 2
38

32 3
38

32 4
38

32 5
38

PART # 203122 203250 N156042
N16474
N16349
201355

Battle Ax Light – Skid Loader OM

4 3
5
2
DESCRIPTION ROTOR, 51″ BA SPIRAL W/O CUTTER 8″ ROTOR, 61″ BA SPIRAL W/O CUTTER 8″
TOOTH, SHANKLESS (51″) (61″)
WASHER, 3/4 NORDLOCK (51″) (61″)
BOLT, 3/4 X 2-1/2 FN TH GR 8 (51″) (61″)
HOLDER, BXL TOOTH HOLDER (51″) (61″)
43

Parts Identification
Rotor Assembly with Planer Teeth; 51″ (203530), 61″ (203532)

12

67

3

45

54 32 11

8

10 12

9

7 6

3

  • For parts breakdown of item 8, 51″ Rotor (203529) and 61″ Rotor (203531), see page 45.

1 2 3 4 5 6 7

8
9 10 11 12
44

QTY. 8 8 2 10 10 2 2 1 1 1 1 1 1

PART # 201358 N16471 201356
4494 N16473 203132 201357 203529 203531 201359
4075 4076 4468

DESCRIPTION BOLT, 7/16″ X 2″ GR 8 FN TH WASHER, 7/16 NORDLOCK BEARING, 1-3/4″ PILOT ROLLER
BOLT, 5/8-18 X 2-1/4 GR 8 WASHER, 5/8 NORDLOCK MOUNT, BEARING WELDMENT ANTIWRAP, 1 PIECE CARBIDE 8″ ROTOR, 51″ BATTLE AX W/PLANER TOOTH ROTOR, 61″ BATTLE AX W/PLANER TOOTH BUSHING, 1-3/4″ID X 2-1/4″OD
WASHER, 2-5/8″ OD WASHER, 1/2″ EXT CNTSK LOCK BOLT, 1/2-20UNF X 1-1/4 FL HD
Battle Ax Light – Skid Loader OM

Rotor with Planer Teeth; 51″ (203529), 61″ (203531)

Parts Identification

1

QTY.

1 1
1

32 2
38

32 3
38

32 4
38

32 5
38

PART # 203122 203250 202970
N16474
N16349
201355

Battle Ax Light – Skid Loader OM

4 3
5
2
DESCRIPTION ROTOR, 51″ BA SPIRAL W/O CUTTER 8″ ROTOR, 61″ BA SPIRAL W/O CUTTER 8″ TOOTH, QUADCO PLANER W/MOD TIP (51″)
(61″) WASHER, 3/4 NORDLOCK (51″)
(61″) BOLT, 3/4 X 2-1/2 FN TH GR 8 (51″)
(61″) HOLDER, BXL TOOTH HOLDER (51″)
(61″)
45

Parts Identification
Motor Assembly; 51″ (209025), 61″ (209026)

6 (Tank)

2 4

1 2 3*

31

5

27

29

28

7

32

30

28

Tank

Pressure Case Drain

11 13 15
14

To Pressure Gauge
11 8 (Pressure)
10

26

11

25

16

11

18 24

20 19

9 12

25 23

17 23
22

  • For parts breakdown of item 3, Overhung Load Adapter (N16416), see page page 48.

21

46

Battle Ax Light – Skid Loader OM

Parts Identification

Motor Assembly; 51″ (209025), 61″ (209026)

QTY.

1

2

2

8

3

1

4

6

5

1

6

1

1 7
1

8

1

9

1

1 10
1

11

4

12

1

13

1

14

1

15

1

1 16
1

17

1

18

2

19

2

20

2

21

1

22

1

23

2

24

1

25

2

26

1

27

1

28

2

29

1

30

1

31

1

32

1

PART # N31536 N16472 N16416
4513 208178 N11945 203639 203640 N21380 N21333 209027 209029 N26204 N155816 N37279 203568 N29078 202720 N51110 205054 N16072 N16468
4230 N19068 N28902 202975 200382 203419 203569 N24822 N15893 N32002 N15895 N24823 203421

DESCRIPTION BOLT, 1/2 X 1-3/4 12 PT GRD8
WASHER, 1/2 NORDLOCK ADAPTER, OVERHUNG LOAD MOTOR #2
BOLT, 1/2″ X 1-1/4″ GRADE 8 MOTOR, 45CC W CHECK & RELIEF ELBOW, 90 DEG 12MOR – 12MJIC HOSE, 3/4X48.5-12FJIC-90SH12FJIC – (51″ Model) HOSE, 3/4″ X 58.5 – 12FJIC-90SH12FJIC – (61″ Model)
ADAPTER, 12MJIC – 12 MOR ELBOW, 90 DEG – 12MJIC -12FJIC HOSE, 3/4 X 43.25 -12FJIC-12FJIC90L – (51″ Model) HOSE, 3/4 X 53.25-12FJIC-12FJIC90L – (61″ Model) ELBOW, 90 DEG – 6MJIC – 6MOR
HOSE, 1/4 X 31 -4FPSW -6FJIC TEE, -6MJIC-6FJIC-6MJIC
HOSE, 3/8″ X 53.5″-6FJIC-6FJIC ELBOW, 90 DEG – 6MJIC – 6FJIC HOSE, 1/4″ X 27 ″-06FJIX-06FJIX – (51″ Model) HOSE, 1/4″ X 32″-06FJIX-06FJIX – (61″ Model)
VALVE, RELIEF 200 PSI BOLT, 1/4″ X 2″ GR. 5 FULL THD
WASHER, 1/4 NORDLOCK NUT, STANDARD 1/4″
ELBOW, 90 DEG – 6MJIC – 8FJIC ELBOW, 90DG TUBE 12MJIC-12FJIC ADAPTER, 45 BULKHEAD -12MJIC
ADAPTER, 45 BULKHEAD -8MJIC HOSE, 3/4″ X 73″ -12FJIC -12MOR HOSE, 1/2IN X 74IN 8FJIC – 8MOR
DECAL, PRESSURE CAP, 3/4 ALUMINUM HOSE
PLUG, 3/8 SCH 40 X .25 CAP, 1/2 ALUMINUM HOSE
DECAL, RETURN WRAP, HOSE 70″

Battle Ax Light – Skid Loader OM

47

Parts Identification
Overhung Load Adapter (N16416)

3 2

2 3 4

7 6 5

1

1 2 3 4 5 6 7

48

QTY. 1 2 2 1 1 1 1

PART # N14151 N14152 N14153 N14154 N14156 N14157 N14158

DESCRIPTION SEAL, FRONT (1.50″ I.D. X 2.13″ O.D. X .312″ THK)
CUP, BEARING CONE, BEARING
SHAFT RING, RETAINING SEAL, REAR (55MM X 90MM X 10MM)
GASKET
Battle Ax Light – Skid Loader OM

Right Hand Hose Kit (208093)

Parts Identification

1*

2*

2*

Case Drain

3

3

8 – Tank

4
5 6 7

9 – Pressure Detail A

Detail A 11

Detail B

10 – Case Drain Detail B

  • Re-use items 1 and 2 when converting.

QTY.

1

1

2

2

3

2

4

2

5

2

6

1

7

2

8

1

9

1

10

1

11

1

PART # 203421 203419 N34029
4054 4068 207813 4465 208095 208094 208096 N159526

Battle Ax Light – Skid Loader OM

DESCRIPTION WRAP, HOSE 76 HOSE, 3/4 X 73 -12FJIC -12MORB ADAPTER, 90 BULKHEAD -12MJIC NUT, LOCK 1/2″ TOP WASHER, 1/2″ SAE FLAT PLATE, BULKHEAD MOUNT 3/4 BOLT, 1/2″ X 1″ GRADE 8 HOSE, 3/4 X 37 -12FJIC -12FJIC90 HOSE, 3/4 40 -12FJIC -12FJIC90 HOSE, 1/2 113 -8FJIC90 -8MORB WRAP, HOSE 45
49

Parts Identification
Machine Decals and Signs
NOTE: All safety related decals are also shown in the Safety Instructions Section along with their location on the machine. See “Safety Decal Locations” on page 8.
Check and replace any worn, torn, hard to read or missing decals on your machine.
Part No. N17013

Part No. N28386 Part No. 200491

Part No. N28385

Part No. 4256

Part No. 4334
Part No. N23506
WARNING
SKIN PUNCTURE HAZARD.
HYDRAULIC LINES. Protect hands and body from high pressure fluids.
N23506
50

Part No. N68716 Battle Ax Light – Skid Loader OM

Machine Decals and Signs (Cont’d)
Part No. 203264

Parts Identification
Part No. N13721

Part No. 200490

Part No. N28576 – (Large) Part No. N28577 – (Small; on Thumb)

Part No. 207851
CASE DRAIN PROTECTION DO NOT CAP
207851
Part No. N28010

Part No. N33105

Part No. N13517

Part No. 4138

Battle Ax Light – Skid Loader OM

51

52

Battle Ax Light – Skid Loader OM

Specifications
DESCRIPTION
Cutting Width Operating Capacity
Motor Rotor Bearings Rotor Tip Diameter Mount Shear Bar Knives Skid Shoes Deflector Anti-Wrap Protection

Appendix

BATTLE AX LIGHT

51″

61″

51.0 in. (129.5 cm)

61 in. (154.9 cm)

6 in. (15.2 cm) Continuous

8 in. (20.3 cm) Intermittent

Fixed Displacement Gear Motor – 45cc (2.75ci)

1.75 in. Piloted Double Taper

13.5 in. (34.3 cm)

Universal Skid Steer

Adjustable

Shankless or Planer Teeth

Stationary

Steel Chain

Bearing

Battle Ax Light – Skid Loader OM

53

Appendix
Dimensions

D

A

C

B

DESCRIPTION Cutting Path (A) Overall Width (B) Overall Depth (C) (without pusher) Overall Height (D) (without pusher) Number Of Teeth Crated Weight (with pusher)
54

BATTLE AX LIGHT

51″

61″

51.0 in. (129.5 cm)

61 in. (154.9 cm)

66.0 in. (167.6 cm)

76.0 in. (193.0 cm)

30.0 in. (76.2 cm)

30.875 in. (78.4 cm)

32

38

~1,454 lbs. (659.5 kg)

~1,606 lbs. (728.5 kg)

Battle Ax Light – Skid Loader OM

Torque Specifications
Inches Hardware and Lock Nuts

Appendix

Battle Ax Light – Skid Loader OM

55

Appendix
Torque Specifications (Cont’d)
Metric Hardware and Lock Nuts

56

Battle Ax Light – Skid Loader OM

www.loftness.com
Loftness Specialized Equipment, Inc. 650 So. Main Street · PO Box 337 · Hector, MN 55342 Tel: 320.848.6266 · Fax: 320.848.6269 · Toll Free: 1.800.828.7624
Printed in USA © Loftness 2021

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals