AGJ BCT-6850 Restaurant Pager System User Manual
- June 16, 2024
- AGJ
Table of Contents
AGJ BCT-6850 Restaurant Pager System
Product List
| Coaster pager | Touch Keypad |
|---|---|
| Pager frequency | 315Mhz |
| Pager dimension | 105×105×15mm |
| Pager weight | 50g |
| Shell material | ABS Plastic |
| Color | Wine red with yellow rubber rim |
| Prompt mode | Ring, vibration, flash |
| Label OEM | Customized |
| Display | 3 digit, LED |
| Pager battery | Built-in 3.7V 300mAh battery Low battery indicator |
| power | 360mW |
| Manufacturer | Wirelesslinkx.com |
| Standby time | 48 hours |
Instructions
-
Charging: Before using, please connect the charging base to power, and put the pagers stacked on the charger for 10 minutes to charge. Before doing any setting, the pagers have to be charged on the charging base. After taking the pager off the base, within 3 seconds the setting can be done.
If the setting failed, put the pager back to the charger and take it off again and repeat the settings.
Setup function can only be pressed / accessed in 3 seconds after the Keypad is connected to power. Within 3 seconds, press back button twice and press setup button. The keypad will show “F1”.
If it passes 3 seconds and can not access to F1, please disconnect the Keypad from power and connect it to power again. -
Switch On Pager : Connect the charging base to power. And put the pagers on the charging base. Pagers will be switched on.
-
Switch Off Pager: Connect the charging base to power, and put the pagers on the charging base.
Input 0 on the Keypad and call all pagers. And all pagers will be switched off. Pagers need to be paired with Keypad first. -
Keypad ID Setting: After the Keypad is connected to power, it will show a number on the display. It is Keypad ID number. Within 3 seconds, press back button and press setup button. The Keypad will show “F1”. If the setup function can not be accessed, please disconnect and connect power of the keypad. And press Setup in 3 seconds. Press confirm button to enter, the display shows “0”. Press the number buttons to change the displayed number. After setting, press the confirm button to save and it will automatically return to F1. Press back button to exit.
If Keypad ID is changed, all pagers need to be paired with the Keypad again. -
Pager Number Setting: After the Keypad is connected to power, it will show a number on the display.
It is Keypad ID number.Within 3 seconds, press back button and press setup button. The Keypad will show “F1”.
If the setup function can not be accessed, please disconnect and connect power of the keypad. And press Setup in 3 seconds. Press + button once, and it will show F2. Press confirm button to enter, the display shows “0”. Press the number buttons to change the displayed number. Take off one pager that is being charged, and press the confirm button within 3 seconds. If the pager flashes and buzzes, pairing is successful.
If the setting failed, put the pager back to the charger and take it off again and repeat the settings above. -
Pager Prompt Time: After the Keypad is connected to power, it will show a number on the display. It is Keypad ID number.Within 3 seconds, press back button and press setup button. The Keypad will show “F1”.
If the setup function can not be accessed, please disconnect and connect power of the keypad. And press Setup in 3 seconds. Press + button twice, and it will show F3. Press confirm button to enter, the display shows “0”. Press the number buttons to change the displayed number. When set to 0, the pager will keep buzzing when called. Number 1 means pagers will buzz or shake for 1 second. 250 seconds is the maximum buzzing / shaking time. Take off one charging pager, and press the confirm button within 3 seconds. If the pager flashes and buzzes, it is successful. If the setting failed, put the pager back to the charger and take it off again and repeat the settings above. -
Pager Beep Setting: After the Keypad is connected to power, it will show a number on the display. It is Keypad ID number.Within 3 seconds, press back button and press setup button. The Keypad will show “F1”.
If the setup function can not be accessed, please disconnect and connect power of the keypad. And press Setup in 3 seconds. Press + button 3 times, and it will show F4. Press confirm button to enter, the screen displays “0”. Press the number buttons to change the displayed number. 0 means beep is shut off, 3 means pager can beep. Take off one charging pager, and press the confirm button within 3 seconds. If the pager flashes and beeps, it is successful. If the setting failed, put the pager back to the charger and take it off again and repeat the settings above.
Note: Two and more Keypads can call one pager. Please change the Keypads’ ID to the same ID number. When the ID is changed, all the pagers need to be paired with the Keypad again to work.