AGJ BCT-6845 Restaurant Pager System Wireless Calling System Instructions
- June 15, 2024
- AGJ
Table of Contents
AGJ BCT-6845 Restaurant Pager System Wireless Calling System
Functional Diagram
Parameter
Keyboard
|
Pager
---|---
Input Power| DC12V/2A| Battery| Li-ion 3.7V 300mAh
Frequency| 433.92MHz| Frequency| 433.92MHz
Transmit Power| 26dBm| Standby Current| <12mA
Standby Power| <120mW| Standby Duration| 10h
Modulation Type| FSK| Sensitivity| -115dBm
Max Capacity| 998 pagers| Max Distance| 800 meters in open space
Charging for pagers| 10pcs2| Prompt Mode| Vibration/Buzzer/Flash
Dimensions| 220215*26mm| Prompt Time| 30 seconds
Instructions
Charging:
Connect keyboard to power, and charge the pagers for 10 minutes at least before using.
Charging Indicator Light Information:
Charging Light Flashes: | Charging |
---|---|
Charging Light Always On: | Fully Charged |
Operating Instruction:
CALL mode is the default mode. Keep pressing Delete button (←) to return to
Call Mode when in other modes. C— is displayed in CALL mode.
Input the number and press CALL button to call the pager.
Pager Mute Mode:
Press MUTE and 999 (S999 displayed) then press CALL, all charging pagers
change to MUTE mode.
Press MUTE and 000 (S000 displayed) then press CALL, all charging pagers
change to normal mode.
In MUTE mode, all pagers only vibrate and flash when called.
Keep pressing DELETE button (←) to return CALL mode. (C— displayed)
Keyboard Mute Mode:
Press MUTE and 998 (S998 displayed) then press CALL, keyboard will not beep
when pressed.
Press MUTE and 997 (S997 displayed) then press CALL, keyboard will beep when
pressed.
Call History:
Press button H to check the recent 10 called numbers (HXXX displayed). Press △/▽ button to page up/down.
Keep pressing DELETE button (←) to return CALL mode. (C— displayed)
Note: No looping of △/▽.
One-Call-Off
In CALL mode, press 999 and press CALL, all charging pagers will be
turned off.
Note: This instruction is invalid to the pagers not being charged.
Pair Operation:
All pagers are paired before delivery. So this operation is only necessary when adding new pagers or changing pager numbers. Put the pagers on the charging base, press P and 999 (P999 displayed), then press CALL to enter pairing mode. The pairing must be finished in 20 seconds after pagers are charged. In pairing mode, all LED of the pagers will keep flashing. Then input number and press CALL, and all pagers will display this number. Move the top pager away, and the pager will beep once and stop flashing. It means the pager is paired. Repeat the steps above to pair other pagers.
Note: The pagers will quit pairing mode if no operation within 1 minute. All pagers’ numbers will not change if not being paired.
One pager only can be programmed with 1 number. Old number will be replaced by the new one.
Instruction Description
Instruction | Buttons | Display | Function |
---|---|---|---|
Pairing Mode | P+999+CALL | P999 | To enter pairing mode |
History | H | H + Number | Check recent 10 call records. |
Mute Mode | +999+Call | S999 | All charging pagers in MUTE mode. |
Quit Mute Mode | +000+Call | S000 | All charging pagers in normal mode. |
Call pagers | [Number]+Call | C+[Number] | The pager will shake / flash / beep. |
Common Defaults and Solutions
Defaults | Analysis | Solution |
---|---|---|
The pager can’t be paired. |
- The pager is not being charged.
- Charging is over 20 seconds.
|
- Make sure the pagers are well charged.
- Try again within 20s after recharging.
The pager can’t be One-Call-Off| The pager is not being charged.| Make sure
the pagers are well charged and try again.
The pager doesn’t response.|
- The pager is out of power.
- Out of call range.
|
- Use after fully charged.
- Use within range of call.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>