AGJ Restaurant Pager Wireless Calling System User Manual

AGJ Restaurant Pager Wireless Calling System User Manual

Wireless Paging System User Manual

Change Paper Number

Parameter

• The parameters were measured in laboratory. They may vary depend on using environment.

Instructions

A.Before using

1. Please charge for more than 10 mins before using.

2. LEDs fast flash during charging, while stay on when fully charged.

B. Programming

1. Press and hold gear button for 3 seconds, F1 will show on the display.

2. Press CALL, charging indicators on pagers turn off, and other indicators turn on. 000 flashes on transmitter.

3. Pick up a pager, and input numbers (1-998). Then press CALL to confirm

4. The pager long beeps. Programming is done. Repeat above steps to program other pagers.

C.Calling

1. Input the number and press CALL.

2. The called pager start alarm.

3. Press here to stop alarm.

4. Putting back the pager to charging slot can stop alarm, too.

D.One-Call-Off

1. Call 999, all charging pagers will be off.

2. All LEDs are off if taking out the pager. Re-charge pagers will turn on again. This instruction is invalid to the pagers not being charged

Settings

1. Press Gear button once or press and hold for 3 seconds to enter F1. In F1-F4, number buttons can not be used. Only use buttons to change the displayed number, or change from F1 to F4.
2. Return to the previous menu & Cancel the operation.
3. In working state, they are used to check recent 10 called numbers. The showing number can be re-called by pressing CALL In setting mode, they are used to switch from F1 to F4. Press CALL to enter from F1 to F4.
4. In F2, use UP or DOWN buttons to choose from 000 to 012 settings. When the keyboard is in F2 functions, the display will show a specific number from 000 to 012. Use UP or DOWN to change the number. From number 000- 003, the settings are for the keyboard. When it shows 000-003, press CALL button to change and save. From number 004-012, the settings are for the pagers. All pagers must be always in the charging slot. The setting will be programmed on this pager. Always press BACK button to exit.
5. In F3, press CALL to enter and input a number and press CALL to save to change the pager prompt time. All pagers must be always in the charging slot.
6. In F4 , press CALL to enter and input a number and press CALL to save to change the keyboard ID. When the ID is changed, all pagers need to be paired again with this keyboard.

on keyboard when pressed.
001| Keyboard only beeps| In 001 and press call, keyboard only beeps when pressed.
002| Keyboard only vibrates| In 002 and press call, keyboard only vibrates when pressed.
003| Keyboard beeps & vibrates| In 003 and press call, keyboard will beep & vibrate when pressed
004| Pager, beep mode| In 004 and press call, pager works by beep only.
005| Pager, vibration mode| In 005 and press call, pager works by vibration only.
006| Pager, LED flash mode| In 006 and press call, pager works by flashing LED only.
007| Pager, beep + vibration| In 007 and press call, pager works by beep & vibration both.
008| Pager, vibration + LED flash| In 008 and press call, pager works by vibration & LED both.
009| Pager, beep + LED flash| In 009 and press call, pager works by beep & LED both.
010| Pager, beep + vibration + LED flash| In 010 and press call, pager works by beep & vibration & LED.
011| Pager will beep slowly| In 011 and press call, pager will beep slowly when called.
012| Pager will beep fast| In 012 and press call, pager will beep in a fast speed when called.
F3| | Beep / Vibrate / Flash Time| In F3, 000 is displayed. Input number(1-999) and press CALL. The prompt time can be set from 1 to 999 seconds.
F4| | Keyboard Transmitter ID| In F4, press CALL, and the original ID is displayed. Input number from 1 to 999 and press CALL can change the ID. When the ID is changed, all pagers need to be paired again.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>