KICHLER 52645CPZ Palta 48 Inch 10 Light Linear Chandelier Instruction Manual Product Specifications Product Usage Instructions
- January 16, 2024
- KICHLER
Table of Contents
- 52645CPZ Palta 48 Inch 10 Light Linear Chandelier
- Product Specifications
- Product Usage Instructions
- Installation Instructions
- FAQ
- Q: How many stems should be used when mounting the
- Q: Why is thread locking compound necessary for the stem
- Q: How should the swivels be installed on a sloped/vaulted
- Q: How should the hex nut, large lock washer, inspection cable,
52645CPZ Palta 48 Inch 10 Light Linear Chandelier
Product Specifications
- Product Model: [Insert Model Name]
- Product Dimensions:
- Height (H): [Insert Height]
- Diameter (D): [Insert Diameter]
- Mounting Strap Length (E): [Insert Length]
- Stem Length (A): [Insert Length]
- Threaded Tube Length (B): [Insert Length]
- Weight: [Insert Weight]
- Power Supply: [Insert Voltage and Frequency]
- Maximum Wattage: [Insert Maximum Wattage]
- Materials:
- Fixture: [Insert Material]
- Coupling: [Insert Material]
- Mounting Strap: [Insert Material]
- Canopy: [Insert Material]
- Hex Nut: [Insert Material]
- Lock Washers: [Insert Material]
- Swivel: [Insert Material]
- Inspection Cable: [Insert Material]
- Reinforcement Plate: [Insert Material]
Product Usage Instructions
Installation Instructions
-
On the side of the fixture with fixture wires, pass the fixture
wires from the coupling (C) through the desired number of short
threaded tubes (B) and stems (A). Screw the stems together using
the short threaded tubes.
NOTE: A minimum of one (1) 6-inch stem must be
used when mounting the fixture.
NOTE: Apply thread locking compound to all stem
threads marked with symbol (4) to prevent accidental rotation of
the fixture during cleaning, relamping, etc. -
On the side of the fixture without fixture wires, screw a
second set of stems together using the same number of short
threaded tubes as in Step 1 (same number of stems and short
threaded tubes as in Step 1, but without fixture wires). -
On the side of the fixture with fixture wires, screw the first
stem of the connected set of stems into the coupling (C). Repeat on
the side of the fixture without fixture wires for the second set of
connected stems. -
On both sides of the fixture, unscrew the hex nuts (I) from the
threads protruding into the canopy (F). Retain the hex nuts. -
Remove the large lock washers (N), inspection cable (M), and
reinforcement plate (O) from the threads inside the canopy.
Carefully remove the swivels (L) from the bottom of the canopy.
Retain the large lock washers, inspection cable, reinforcement
plate, and swivels. -
On the side of the fixture with fixture wires, pass the fixture
wires through the swivel (L) and screw the swivel into the last
stem. Ensure that you align the direction of the swivel according
to the ceiling, especially if mounting the fixture to a sloped or
vaulted ceiling. -
On the side of the fixture without fixture wires, screw the
swivel into the last stem. Ensure that the second swivel is
installed in the same direction as the first swivel. -
Carefully lower the reinforcement plate (O) back into the
canopy (F), aligning the holes in the reinforcement plate with the
holes in the canopy. -
On the side of the fixture with fixture wires, carefully pass
the fixture wires and threads at the top of the swivel through the
holes in the bottom of the canopy and reinforcement plate. On the
side of the fixture without fixture wires, carefully pass the
threads at the top of the swivel through the holes in the bottom of
the canopy and reinforcement plate. -
On the side of the fixture with fixture wires, pass the fixture
wires through the bracket on the end of the inspection cable. Pass
the bracket on the end of the inspection cable over the swivel
threads protruding through the reinforcement plate. -
Pass the fixture wires through the large lock washer and slip
it over the swivel threads. -
Pass the fixture wires through the hex nut and thread it onto
the swivel threads. Tighten to secure the hex nut, large lock
washer, inspection cable, reinforcement plate, and canopy to the
swivel. -
On the side of the fixture without fixture wires, slip the
large lock washer over the swivel threads.
FAQ
Q: How many stems should be used when mounting the
fixture?
A: A minimum of one (1) 6-inch stem must be used when mounting
the fixture.
Q: Why is thread locking compound necessary for the stem
threads?
A: Thread locking compound must be applied to all stem threads
as noted with symbol (4) to prevent accidental rotation of the
fixture during cleaning, relamping, etc.
Q: How should the swivels be installed on a sloped/vaulted
ceiling?
A: The swivels should be installed in accordance with the
direction of the ceiling slope to assist in mounting the fixture to
a sloped/vaulted ceiling.
Q: How should the hex nut, large lock washer, inspection cable,
reinforcement plate, and canopy be secured to the swivel?
A: Pass the fixture wires through the bracket on the end of the
inspection cable, slip the large lock washer over the swivel
threads, pass the fixture wires through the hex nut, and tighten it
to secure all components to the swivel.
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
FIXTURE DIAGRAM
H
D
E
M
G I
O
N
F
J
K
L
A
B
C
PARTS LIST [A] Stems, (2-6″ Stems, 2-12″
Stems with Short Threaded Tubes[B] attached) [B] Short Threaded Tubes [C]
Coupling [D] Strap Mounting Screw (Qty. 2)
[E] Mounting Strap [F] Canopy [G] Mounting Screw (Qty. 2) [H] Outlet Box (not supplied) [I] Hex Nut (Qty. 2) [J] Small Lock Washer (Qty. 2) [K] Knob (Qty. 2) [L] Swivel (Qty. 2) [M] Inspection Cable [N] Large Lock Washer (Qty. 2) [O] Reinforcement Plate
CAUTIONS CAUTION RISK OF SHOCK: Disconnect Power at the main circuit breaker
panel or main fusebox before starting and during the installation. WARNING: 1.
This fixture is intended for installation in accordance with the National
Electrical Code (NEC)
and all local code specifications. If you are not familiar with code
requirements, installation by a certified electrician is recommended. Failure
to adhere to these codes and instructions may result in serious injury and/or
property damage and will void the warranty. CLEANING: · Always be certain that
electric current is turned off before cleaning. · Only a soft damp cloth
should be used. Harsh cleaning products may damage the finish.
INSTALLATION INSTRUCTIONS
1. On side of fixture with fixture wires, pass fixture wires from coupling[C]
through desired number of short threaded tubes[B] and stems[A]. Screw stems
together using short threaded tubes.
NOTE: A minimum of one (1) 6-inch stem must be used when mounting fixture.
NOTE: Thread locking compound must be applied to all stem threads as noted
with symbol (4) to prevent accidental rotation of fixture during cleaning,
relamping, etc.
2. On side of fixture without fixture wires, screw a second set of stems
together using short threaded tubes (same number of stems and short threaded
tubes as in Step 1, but without fixture wires).
3. On side of fixture with fixture wires, screw first stem of connected set
of stems into coupling[C]. Repeat on side of fixture without fixture wires for
the second set of connected stems.
4. On both sides of fixture, unscrew hex nuts[I] from threads protruding into
canopy[F]. Retain hex nuts.
5. Remove large lock washers[N], inspection cable[M], and reinforcement
plate[O] from threads inside of canopy. Carefully remove swivels[L] from
bottom of canopy. Retain large lock washers, inspection cable, reinforcement
plate, and swivels.
6. On side of fixture with fixture wires, pass fixture wires through
swivel[L] and screw swivel into last stem.
Note direction of swivel in accordance with ceiling. The swivels will help
with mounting fixture to a sloped/vaulted ceiling.
7. On side of fixture without fixture wires, screw swivel into last stem.
NOTE: The 2nd swivel should be installed in the same direction as the 1st
swivel.
INSTALLATION INSTRUCTIONS (CONTINUED)
8. Carefully lower reinforcement plate[O] back into canopy[F], aligning the
holes in the reinforcement plate with the holes in the canopy.
9. On side of fixture with fixture wires, carefully pass fixture wires and
threads at top of swivel through holes in bottom of canopy and reinforcement
plate. On side of fixture without fixture wires, carefully pass threads at top
of swivel through holes in bottom of canopy and reinforcement plate.
10. On side of fixture with fixture wires, pass fixture wires through bracket
on end of inspection cable. Pass bracket on end of inspection cable over
swivel threads protruding through reinforcement plate.
11. Pass fixture wires through large lock washer. Slip large lock washer over
swivel threads.
12. Pass fixture wires through hex nut. Thread hex nut onto swivel threads.
Tighten to secure hex nut, large lock washer, inspection cable, reinforcement
plate, and canopy to swivel.
13. On side of fixture without fixture wires, slip large lock washer over
swivel threads.
14. Thread hex nut onto swivel threads. Tighten to secure hex nut, large lock
washer, reinforcement plate, and canopy to swivel.
15. Cut fixture wires a MINIMUM of 20 inches from the top edge of canopy.
16. Find the appropriate threaded holes in mounting strap[E] that align with
hole distance in canopy.
17. Assemble mounting screws[G] into threaded holes in mounting strap,
starting from the outlet box side.
18. Attach mounting strap to outlet box[H] using the strap mounting
screws[D]. Mounting strap can be adjusted to suit position of fixture.
19. Attach inspection cable[M] to the mounting strap or to the inside of the
outlet box and secure into place to prevent damage to the wires during wiring.
20. Grounding instructions: (See Illus. a or b).
a. On fixtures where mounting strap is provided with a hole and two raised
dimples, wrap ground wire from outlet box around green ground screw, and
thread into hole.
b. On fixtures where a cupped washer is provided, attach ground wire from
outlet box under cupped washer and green ground screw, and thread into
mounting strap.
If fixture is provided with ground wire, connect fixture ground wire to outlet
box ground wire with wire connector after following the above steps. Never
connect ground wire to black or white power supply wires.
a
WIRE CONNECTOR
b
OUTLET BOX GROUND
FIXTURE GROUND
FIXTURE GROUND
DIMPLES
OUTLET BOX GROUND
GREEN GROUND SCREW
GREEN GROUND SCREW
CUPPED WASHER
21. Make wire connections. Reference chart below for correct connections and wire accordingly.
Connect Black or Red Supply Wire to:
Connect White Supply Wire to:
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black Clear, Brown, Gold or Black
without Tracer
with Tracer
Insulated wire (other than green) with copper
conductor
Insulated wire (other than green) with silver
conductor
*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)
Neutral Wire
22. Raise canopy to ceiling, carefully passing mounting screws through
mounting screw holes in reinforcement plate and canopy.
NOTE: Be certain wires do not get pinched between mounting strap and canopy or
canopy and ceiling.
23. Use small lock washers[J] and knobs[K] to secure canopy. Tighten to
secure.
24. Install the recommended bulbs (Not supplied).
REV 22-AUG-2023
For warranty information please visit: kichler.com/warranty
IS-52645-US
INSTRUCTIONS: For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
Nous sommes là pour vous aider 866-558-5706
Heures : du lundi au vendredi, de 9h à 17h (heure de l’Est)
DIAGRAMME D’APPAREILS
H
D
E
M
G I
O
N
F
J
K
L
A
B
C
LISTE DES PIÈCES [A] Tiges (Tiges de 2-6 po ;
Tiges de 2-12 po avec des Tubes Filetés Courts[B] installés). [B] Tubes
Filetés Courts [C] Accouplement [D] Vis de Montage de L’étrier (Qté 2)
[E] Étrier de Montage [F] Cache [G] Vis de Montage (Qté 2) [H] Boîte de Sortie
(non
fournie) [I] Écrou Hexagonal (Qté 2) [J] Petite Rondelle de Blocage
(Qté 2) [K] Boule (Qté 2) [L] Rotule (Qté 2) [M] Câble D’inspection [N] Grande
Rondelle de
Blocage (Qté 2) [O] Plaque de Renforcement
PRÉCAUTIONS ATTENTION RISQUE DE DÉCHARGES ÉLECTRIQUES : Couper le courant au
niveau du panneau du disjoncteur du circuit principal ou de la boîte à
fusibles principale avant de procéder à l’installation. AVERTISSEMENT : 1. Ce
luminaire doit être installé conformément aux codes d’électricité nationaux
(NEC) et satisfaire
toutes les spécifications des codes locaux. Si vous ne connaissez pas les
exigences de ces codes, il est recommandé de confier l’installation à un
électricien certifié. Ne pas se conformer à ces codes et directives pourrait
provoquer des blessures sérieuses et/ou des dommages matériels et rendre la
garantie non valide. NETTOYAGE : · Soyez toujours certain que l’alimentation
électrique du luminaire est fermée avant le nettoyage. · N’utilisez qu’un
chiffon doux humide. Les produits de nettoyage acides/abrasifs peuvent
endommager le fini.
INSTRUCTIONS D’INSTALLATION
1. Sur le côté du luminaire doté des fils, acheminez les fils du luminaire
depuis l’accouplement[C] par le nombre souhaité de tubes filetés courts[B] et
de tiges[A]. Vissez les tiges ensemble à l’aide de tubes filetés courts.
REMARQUE : Utiliser une (1) tige minimum de 15 cm (6 po) pour le montage du
luminaire.
REMARQUE : Appliquer le frein filet sur tous les filets de la tige indiqués
par le symbole (4) pour empêcher la rotation accidentelle du luminaire pendant
le nettoyage, remplacement de lampe, etc.
2. Sur le côté du luminaire sans fils, vissez un deuxième ensemble de tiges
ensemble à l’aide des tubes filetés courts (même nombre de tiges et de tubes
filetés courts que pour l’Étape 1 mais sans les fils de luminaire).
3. Sur le côté du luminaire doté des fils, vissez la première tige de
l’ensemble de tiges connectées dans l’accouplement[C]. Répétez pour le côté du
luminaire sans fil pour le deuxième ensemble de tiges connectées.
4. Sur les deux côtés du luminaire, dévissez les écrous hexagonaux[I] des
filets ressortant du cache[F]. Conservez les écrous hexagonaux.
5. Retirez les grandes rondelles de blocage[N], le câble d’inspection[M] et
la plaque de renforcement[O] des filets à l’intérieur du cache. Enlevez les
rotules avec précaution[L] de la partie inférieure du cache. Conservez les
grandes rondelles de blocage, le câble d’inspection, la plaque de renforcement
et les rotules.
6. Sur le côté du luminaire doté de fils, acheminez les fils par la rotule[L]
et vissez la rotule dans la dernière tige.
Prenez note du sens de la rotule par rapport au plafond. Les rotules
faciliteront l’installation du luminaire sur un plafond incliné/voûté.
7. Sur le côté du luminaire sans fils du luminaire, vissez la rotule dans la
dernière tige.
REMARQUE : La 2e rotule doit être installée dans la même direction que la
1ière.
INSTRUCTIONS D’INSTALLATION (SUITE)
8. Rabaissez soigneusement la plaque de renforcement[O] dans le cache[F] en
prenant soin d’aligner les trous de la plaque de renforcement aux trous dans
le cache.
9. Sur le côté du luminaire doté de fils, acheminez soigneusement les fils et
les filets en haut de la rotule par les trous en bas du cache et de la plaque
de renforcement. Sur le côté du luminaire sans fils, acheminez soigneusement
les filets en haut de la rotule par les trous en bas du cache et de la plaque
de renforcement.
10. Sur le côté du luminaire avec fils, passez les fils du luminaire par la
bride située à l’extrémité du câble d’inspection. Passez la bride sur
l’extrémité du câble d’inspection sur les filets de la rotule ressortant de la
plaque de renforcement.
11. Acheminez les fils du luminaire par une grande rondelle de blocage.
Passez la grande rondelle de blocage sur les filets de la rotule.
12. Passez les fils du luminaire par l’écrou hexagonal. Vissez l’écrou
hexagonal sur les filets de la rotule. Serrez pour fixer l’écrou hexagonal,
une grande rondelle de blocage, un câble d’inspection, plaque de renforcement,
et cache sur la rotule.
13. Sur un côté du luminaire sans fils, glissez une grande rondelle de
blocage sur les filets de la rotule.
14. Vissez l’écrou hexagonal sur les filets de la rotule. Serrez pour fixer
l’écrou hexagonal, une grande rondelle de blocage, une plaque de renforcement
et un cache sur la rotule.
15. Coupez les fils du luminaire à 50 cm MINIMUM du bord supérieur du cache.
16. Localisez les trous taraudés appropriés, sur l’étrier de montage[E] qui
s’alignent sur la distance de trou dans le cache.
17. Placez les vis de montage[G] dans les trous taraudés dans l’étrier de
montage en commençant par la boîte de sortie.
18. Fixez l’étrier de montage sur la boîte de sortie[H] à l’aide des vis de
montage de l’étrier[D]. Vous pouvez régler l’étrier de montage en fonction de
la position du luminaire.
19. Fixez bien le câble d’inspection[M] à l’étrier de montage ou à
l’intérieur de la boîte de sortie pour ne pas endommager les fils pendant le
câblage.
20. Connecter les fils. Se reporter au tableau ci-dessous pour faire les
connexions.
Connecter le fil noir ou rouge de la boite
Connecter le fil blanc de la boîte
A Noir
A Blanc
*Au cordon parallèle (rond et lisse)
*Au cordon parallèle (à angles droits el strié)
Au transparent, doré, marron, ou noir sans fil
distinctif
Au transparent, doré, marron, ou noir avec un til
distinctif
Fil isolé (sauf fil vert) avec Fil isolé (sauf fil vert) avec
conducteur en cuivre
conducteur en argent
*Remarque: Avec emploi d’un fil paralléle (SPT 1 et SPT 2). Le fil neutre est á angles droits ou strié et l’autre fil doit étre rond ou
lisse (Voir le schéma).
Fil Neutre
21. Soulevez le cache en direction du plafond en passant soigneusement les
vis de montage par les trous des vis de montage dans la plaque de renforcement
et le cache.
REMARQUE : S’assurer que les fils ne se coincent pas entre l’étrier de montage
et le cache ou le cache et le plafond.
22. Utilisez les petites rondelles de blocage[J] et les boules[K] pour
bloquer le cache. Serrez pour fixer.
23. Installez les ampoules recommandées (non fournies).
REV 22-AUG-2023
Pour de plus amples informations sur la garantie, veuillez visiter : kichler.com/warranty
IS-52645-CB
Estamos aquí para ayudarle 866-558-5706
Horario: Lunes-Viernes 9am a 5pm EST (hora oficial del este)
DIAGRAMA DE ACCESORIOS
H
D
E
M
G I
O
N
F
J
K
L
A
B
C
LISTA DE PARTES [A] Vástagos, (2- Vástagos
6″, 2- Vástagos 12″ con Tubos Roscados Cortos[B] acoplados) [B] Tubos Roscados
Cortos [C] Acoplamiento [D] Tornillo de Montaje de la Abrazadera (cant. 2)
[E] Abrazadera de Montaje [F] Cubierta [G] Tornillo de Montaje (cant. 2) [H]
Caja de Salida (no
suministrada) [I] Tuerca Hexagonal (cant. 2) [J] Arandela de Seguridad
Pequeña (cant. 2) [K] Perilla (cant. 2) [L] Unión Giratoria (cant. 2) [M]
Cable de Inspección [N] Arandela de Seguridad
Grande (cant. 2) [O] Placa de Refuerzo
PRECAUCIONES PRECAUCIÓN RIESGO DE DESCARGA ELÉCTRICA: Desconecte la
electricidad en el panel principal del interruptor automático o caja principal
de fusibles antes de comenzar y durante la instalación. ADVERTENCIA: 1. Este
accesorio está destinado a la instalación de acuerdo con el National
Electrical Code (NEC)
y todas las especificaciones del código local. Si no está familiarizado con
los requisitos del código, la instalación se recomienda un electricista
certificado. No cumplir con estos códigos e instrucciones puede resultar en
lesiones graves y/ o en daños a la propiedad y anulará la garantía. LIMPIEZA:
· Asegúrese siempre de que la corriente eléctrica esté apagada antes de
limpiar. · Debe usarse solamente un paño húmedo y suave. Productos de limpieza
abrasivos pueden dañar el acabado.
INSTRUCCIONES DE INSTALACIÓN
1. En el lado del artefacto con los cables del artefacto, pase los cables
desde el acoplamiento[C] a través del número deseado de tubos roscados
cortos[B] y vástagos[A]. Enrosque los vástagos entre si utilizando los tubos
roscados cortos.
NOTA: Se debe utilizar como mínimo un (1) vástago de 6 pulgadas cuando se
monte el artefacto.
NOTA: Se debe aplicar compuesto bloqueador de roscas a todas las roscas de
vástagos como se indica con el símbolo (4) para evitar la rotación accidental
del artefacto durante la limpieza, el cambio de focos, etc.
2. En el lado del artefacto sin los cables del artefacto, enrosque un segundo
juego de vástagos entre si utilizando tubos roscados cortos (el mismo número
de vástagos y tubos roscados cortos que en el paso 1, pero sin los cables del
artefacto).
3. En el lado del artefacto con los cables del artefacto, enrosque el primer
vástago del conjunto conectado de vástagos en el acoplamiento[C]. Repita el
procedimiento en el lado del artefacto sin los cables para el segundo juego de
vástagos conectados.
4. En ambos lados del artefacto, desenrosque las tuercas hexagonales[I] de
las roscas que sobresalen hacia la cubierta[F]. Guarde las tuercas
hexagonales.
5. Retire las arandelas de seguridad grandes[N], el cable de inspección[M] y
la placa de refuerzo[O] de las roscas del interior de la cubierta. Retire con
cuidado las uniones giratorias[L] de la parte inferior de la cubierta.
Conserve las arandelas de seguridad grandes, el cable de inspección, la placa
de refuerzo y las uniones giratorias.
6. En el lado del artefacto con los cables, pase los cables del artefacto a
través de la unión giratoria[L] y enrosque la unión giratoria en el último
vástago.
Observe la dirección de la unión giratoria de acuerdo con el techo. Las
uniones giratorias ayudarán a montar el artefacto en techos inclinados o
abovedados.
7. En el lado del artefacto sin los cables del artefacto, enroscar la unión
giratoria en el último vástago.
NOTA: La 2ª unión giratoria debe instalarse en la misma dirección que la 1ª.
INSTRUCCIONES DE INSTALACIÓN (CONTINUACIÓN)
8. Vuelva a bajar con cuidado la placa de refuerzo[O] hacia la cubierta[F],
alineando los orificios de la placa de refuerzo con los orificios de la
cubierta.
9. En el lado del artefacto con los cables, pase con cuidado los cables del
artefacto y las roscas de la parte superior de la unión giratoria a través de
los orificios de la parte inferior de la cubierta y la placa de refuerzo. En
el lado del artefacto sin los cables, pase con cuidado las roscas de la parte
superior de la unión giratoria a través de los orificios de la parte inferior
de la cubierta y la placa de refuerzo.
10. En el lado del artefacto con los cables, pase los cables del artefacto a
través del soporte en el extremo del cable de inspección. Pase el soporte en
el extremo del cable de inspección sobre las roscas de las uniones giratorias
que sobresalen a través de la placa de refuerzo.
11. Pase los cables del artefacto a través de la arandela de seguridad
grande. Deslice la arandela de seguridad grande sobre las roscas de la unión
giratoria.
12. Pase los cables del artefacto a través de la tuerca hexagonal. Enrosque
la tuerca hexagonal en las roscas de la unión giratoria. Apriete para fijar la
tuerca hexagonal, la arandela de seguridad grande, el cable de inspección, la
placa de refuerzo y la cubierta a la unión giratoria.
13. En el lado del artefacto sin los cables, deslice la arandela de seguridad
grande sobre las roscas de la unión giratoria.
14. Enrosque la tuerca hexagonal en las roscas de la unión giratoria. Apriete
para fijar la tuerca hexagonal, la arandela de seguridad grande, la placa de
refuerzo y la cubierta a la unión giratoria.
15. Corte los cables del artefacto a un MÍNIMO de 20 pulgadas del borde
superior de la cubierta.
16. Encuentre los orificios roscados apropiados en la abrazadera de
montaje[E] que se alinean con la distancia de los orificios en la cubierta.
17. Atornille los tornillos de montaje[G] en los orificios roscados de la
abrazadera de montaje, empezando por el lado de la caja de salida.
18. Fije la abrazadera de montaje a la caja de salida[H] utilizando los
tornillos de montaje de la abrazadera[D]. La abrazadera de montaje puede
ajustarse para adaptarse a la posición del artefacto.
19. Fije el cable de inspección[M] en la abrazadera de montaje o en el
interior de la caja de salida y asegúrelo en su lugar para evitar que se dañen
los cables durante el cableado.
20. Instrucciones de conexión a tierra solamente para los Estados Unidos.
(Vea la ilustracion a o b).
a. En las lámparas que tienen la abrazadera de montaje con un agujero y dos
hoyuelos realzados, enrollar el alambre a tierra de la caja de salida
alrededor del tornillo verde y pasarlo por el aquiero.
b. En las lámparas con una arandela acopada, fijar el alambre a tierra de la
caja de salida del ajo de la arandela acoada y tornillo verde, y paser por la
abrazadera de montaje.
Si la lámpara viene con alambre a tierra, conecter el alambre a tierra de la
lámpara al alambre a tierra de la caja de salida con un conector de alambres
espués de seguir los pasos anteriores. Nunca conectar el alambra a tierra a
los alambres eléctros negro o blanco.
a
TIERRA DE LA CAJA DE SALIDA
CONECTOR DE ALAMBRE
TIERRA ARTEFACTO
b
TIERRA ARTEFACTO
DEPRESIONES
TORNILLO DE TIERRA, VERDE
TIERRA DE LA CAJA DE SALIDA
TORNILLO DE TIERRA, VERDE
ARANDELA CONCAVA
21. Haga les conexiones de los alambres. La tabla de referencia de abajo indica las conexiones correctas y los alambres correspondientes.
Conectar el alambre de Conectar el alambre de suministro negro o rojo al suministro blanco al
Negro
Blanco
Cordon paralelo (redondo Cordon paralelo (cuadrado
y liso)
y estriado)
Claro, marrón, amarillio o negro sin hebra identificadora
Claro, marrón, amarillio o negro con hebra identificadora
Alambre aislado (diferente del verde) con conductor
de cobre
Alambre aislado (diferente del verde) con conductor
de plata
*Nota: Cuando se utiliza alambre paralelo (SPT 1 y SPT 2). El alambre neutro es de forma cuadrada o estriada y el otro
alambre será de forma redonda o lisa. (Vea la ilustracíón).
Hilo Neutral
22. Levante la cubierta hasta el techo, pasando con cuidado los tornillos de
montaje por los orificios de los tornillos de montaje de la placa de refuerzo
y la cubierta.
NOTA: Asegúrese de que los cables no queden apretados entre la abrazadera de
montaje y la cubierta o la cubierta y el techo.
23. Utilice pequeñas arandelas de seguridad[J] y perillas[K] para fijar la
cubierta. Apriete para asegurar.
24. Instale los focos recomendados (No suministrados).
REV 22-AUG-2023
Para informacion de la garantia por favor visite: kichler.com/warranty
IS-52645-US