KICHLER 49151AZ Zolder 2-Light 26.5 Inch Architectural Bronze Outdoor Wall Light Installation Guide
- June 2, 2024
- KICHLER
Table of Contents
KICHLER 49151AZ Zolder 2-Light 26.5 Inch Architectural Bronze Outdoor
Wall Light
IMPORTANT SAFETY INSTRUCTIONS LIGHTED BULB IS HOT!
WARNING: To reduce the risk of FIRE or INJURY TO PERSON:
- Turn off and allow to cool before replacing bulb.
- Bulb gets HOT QUICKLY! Contact switch only when turning off.
- DO NOT remain in light if skin feels warm. (Light is intense, may cause “sunburn”)
- DO NOT look directly at lighted bulb.
- Keep materials away from bulb that may burn.
- Use ONLY with wattage specified or lower.
- DO NOT touch bulb at any time, use a soft cloth. Oil from skin may damage bulb.
- DO NOT operate fixture with missing or damaged glass.
-
TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work without shutting off the electricity until the work is done. -
Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
-
Unscrew the fuse(s), or switch “OFF” the circuit breaker switch(s), that control the power to the fixture or room that you are working on.
-
Place the wall switch in the “OFF” position. If the fixture to be replaced has a switch or pull chain, place those in the “OFF” position.
-
Find the appropriate threaded holes on mounting strap. Assemble mounting screws into threaded holes.
-
Attach mounting strap to outlet box. (Screws not provided). Mounting strap can be adjusted to suit position of fixture.
-
Grounding instructions: (See Illus. A or B).
-
On fixtures where mounting strap is provided with a hole and two raised dimples. Wrap ground wire from outlet box around green ground screw, and thread into hole.
-
On fixtures where a cupped washer is provided. Attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture ground wire to outlet box ground wire with wire connector. (Not provided.) After following the above steps. Never connect ground wire to black or white power supply wires. -
Make wire connections (connectors not provided.) Reference chart below for correct connections and wire accordingly.
Connect Black or Red Supply Wire to:| Connect
White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without tracer| Clear, Brown, Gold or Black with
tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other
than green) with silver conductor
*Note: When parallel wires (SPT I & SPT II) are used. The neutral wire is
square shaped or ridged and the other wire will be round in shape or smooth
(see illus.)|
- Push fixture to wall, carefully passing mounting screws through holes in canopy.
- Thread threaded balls onto mounting screws. Tighten threaded balls to secure fixture to wall.
- Insert recommended bulb into each socket. CAUTION: DO NOT touch bulb with bare hands. If this happens, clean bulb with denatured alcohol and a lint free cloth.
- Lower top glass down over socket.
- Fit bottom edge of glass into cup on fixture.
- Carefully turn glass to secure glass in place. (DO NOT over tighten.)
- Raise bottom glass up to fixture. Pass hole in glass over socket.
- Fit bottom edge of glass into cup on fixture.
- Carefully turn glass to secure glass in place. (DO NOT over tighten.)
INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/OR IN WET LOCATIONS
- Mounting surface should be clean, dry, flat and 1/4” larger that the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- With silicone caulking compound, caulk completely around where back of canopy meets the wall surface to prevent water from seeping into outlet box.
SEE OTHER SIDE FOR SPANISH TRANSLATIONS. VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>