lncoon LN-D51 Car GPS Tracker Instructions

June 16, 2024
lncoon

**lncoon LN-D51 Car GPS Tracker Instructions

**

LN-D51 Command List Send these command in Command - > User-Defined section to set the advanced function *** There should be no spaces** between any commandsFor any further questions, please contact us: Support@Lncoon.com

Query Command
After sending, the device will reply the current status information. The content in bold orange is the key information, which varies according to the current state of the device
No.| Function| Command| Reply Example| Explanation
1| Check Location| URL#| 05-11 18:00 http://maps.google.com/maps?q=N22.551825,E113.940834| Information Contained : Date&TimeLink to check current location Latitude & Longitude
POSITION#
WHERE#| Current position! Lat:N22.57776,Lon:E113.91667,Course:334,Speed:0Km/h,DateTi me:2015-12-28 09:15:12| Information Contained: Date & Time Latitude & Longitude Mileage & Speed

Functional Command

The contents in bold green are restricted parameters, which have a specific format or limited range, please fill in according to the rules given in the Explanation. Please keep the other characters unchanged


No.| Function| Command| Reply Example| Explanation
1| Vibration Alert| SENALM,ON,0#| OK!| Function: Turn on vibration alert (Default off)
SENALM,OFF#| OK!| Function : Turn off vibration alert
SENALM#| SENALM: ON,0| Function: Check current vibration alarm status
2| Set Vibration Sensitivity| LEVEL, M #| OK!| Function: Adjust the sensitivity level of the vibration sensor Sensitivity level: M =1/2/3/4/5, default:2; 1: Highest sensitivity 5: Minimum sensitivity
LEVEL#| LEVEL: 1| Function: Check the current vibration sensitivity level
3| Overspeed Alert| SPEED,ON, T , S ,0, X #| OK!| Function: Turn on overspeed alert (Default off) Detection time: T =5~600, integer in seconds; default:20 seconds; Speed threshold : S =1~255, integer in km/h; default:100 km/h; Device beeping : X =ON/OFF, default: ON;
---|---|---|---|---
SPEED,OFF#| OK!| Function : Turn off overspeed alert
SPEED#| SPEED: ON,20,100,1,ON| Function : Check current overspeed alert status
4| Mileage Calculation| MILEAGE,ON, L #| OK!| Function : Enable mileage calculation (Default off) Initial mileage: L =0~999999, integer in km; default:0 km;
MILEAGE,OFF#| OK!| Function : Disable mileage calculation
MILEAGE#| MILEAGE: ON , 99| Function : Check current total mileage
5| ACC OFF Alert| POWERALM,ON,0, T1 , T2 #| OK!| Function : Turn on ACC off Alert (Default on) When the device detects ACC off for over T1 seconds, it will send an alert. If the ACC is back on for less than T2 seconds, the device will not alert again. ( T2 is used to filter repeated alerts)Power off time: T1 =2~3600, integer in seconds; default:5 seconds; Back to charge time: T2 =1~3600, integer in seconds; default:300 seconds;
POWERALM,OFF#| OK!| Function: Turn off ACC off alert
POWERALM#| POWERALM: ON,2,10,1| Function: Check current ACC off alert status
6| Install Alert| INSTALLALM,ON,0#| OK!| Function : Turn on install alert (Default on) Get notification when device installed on your car
---|---|---|---|---
INSTALLALM,OFF#| OK!| Function: Turn off install alert
INSTALLALM#| INSTALLALM: ON,0| Function : Check current install alert status
7| Unplug Alert| PULLALM,ON,0,20,30#| OK!| Function: Turn on disassembly alert (Default on)
PULLALM,OFF#| OK!| Function: Turn off disassembly alert
PULLALM#| PULLALM: ON,1,20,30| Function: Check current disassembly alert status
9| Low Battery Alarm| BATALM,ON,0#| OK!| Function: Turn on low battery alert (Built-in backup battery) (Default off)
---|---|---|---|---
BATALM,OFF#| OK!| Function : Turn off low battery alert
BATALM#| BATALM: OFF,1| Function : Check current low battery alert status
10| Fatigue Driving Alert| FATIGUEALM,ON, T1 , T2 , T3 ,0, S

| OK!| Function : Turn on fatigue driving alert (Default on) When

driving (ACC on) for more than T1 minutes, the device will send early fatigue alert T3 minutes before T1 reaches (Early Warning Time= T1T3 ), and alert again when T1 actually reaches.
The driver will hear the device beeping if S =ON. The device will ignore the break time (ACC off) under T2 minutes.
Continuous driving time threshold: T1 =60~600, integer in minutes; default:240 minutes; Break time threshold: T2 =1~255, integer in minutes; default:20 minutes; Early warning time: T3 =10~240, integer in minutes; default:30 minutes; ( T3 must be less than T1 )Device beeping : S =ON/OFF, default:ON;
FATIGUEALM,OFF#| OK!| Function : Turn off fatigue driving alert
FATIGUEALM#| FATIGUEALM: ON , 240 , 20 , 30 , 0 , ON| Function: Check current fatigue driving alert setting
11| ACC ON Buzzer| ACCSOUND,ON#| OK!| Function: Turn on buzzer while ACC ON (Default on)
---|---|---|---|---
ACCSOUND,OFF#| OK!| Function : Turn off buzzer while ACC ON
12| All Buzzer Sound| VOLUME,ON#| OK!| Function: Turn on buzzer sound (Default on)
VOLUME,OFF#| OK!| Function: Turn off buzzer sound (for all buzzer alert)
13| Harsh Acceleration| HARACC,ON, A ,0#| OK!| Function : Turn on harsh acceleration alert (Default on) Sensitivity: A =1/2/3, default:1; 1: Highest sensitivity3: Minimum sensitivity
HARACC,OFF#| OK!| Function: Turn off harsh acceleration alert
HARACC#| HARACC: ON,1| Function: Check current harsh acceleration alert setting
14| Harsh Deceleration| HARDEC,ON, A ,0#| OK!| Function: Turn on harsh deceleration alert (Default on) Sensitivity: A =1/2/3, default:1; 1: Highest sensitivity3: Minimum sensitivity
---|---|---|---|---
HARDEC,OFF#| OK!| Function: Turn off harsh deceleration alert
HARDEC#| HARDEC: ON,1| Function: Check current harsh deceleration alert setting
15| Harsh Turn| HARTU,ON, A ,0#| OK!| Function: Turn on harsh turn alert (Default on) Sensitivity: A =1/2/3, default:1; 1: Highest sensitivity3: Minimum sensitivity
HARTU,OFF#| OK!| Function: Turn off harsh turn alert
HARTU#| HARTU: ON,1| Function: Check current harsh turn alert setting
16| Collision| HORCOL,ON, A ,0#| OK!| Function: Turn on collision alert (Default on) Sensitivity: A =1/2/3, default:1; 1: Highest sensitivity3: Minimum sensitivity
HORCOL,OFF#| OK!| Function: Turn off collision alert
HORCOL#| HORCOL: ON,1| Function: Check current collision alert setting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals