lncoon JM-C21 GNSS Vehicle Terminal User Manual

June 12, 2024
lncoon

JM-C21 GNSS Vehicle Terminal
User Manual

Part I – Product Introduction

1.1 Product Overview

lncoon JM C21 GNSS Vehicle Terminal - Product Overview

1.2 Product Schematic

No. Name Quantity Unit Remark
1 Device 1 piece
2 Power Cable 1 piece 1M length
3 Relay 1 set
4 User Manual 1 piece

1.3 Interface Definition

| V+| Red| Anode ( 9-90V )
---|---|---|---
V-| Black| Negative
ACC| Orange| ACC Detection
Relay| Yellow| Oil & Power Cut

1.4 Indicator Definition

  1. GPS Signal Status
    Status| Meaning
    ---|---
    Quick Blinking  (on 0.3s, off 0.3s)| Searching GPS signal
    Solid on| Get GPS Location
    Off| Sleep Mode or Not Working
  2. GSM Signal Status
    Status| Meaning
    ---|---
    Quick Blinking (on 0.3s, off 0.3s)| GSM Initializing
    Slow Blinking (on 0.3s, off 2s)| GSM Signal Receiving Normally
    Solid on| GSM call/GPRS is active
    Off| No signal received
  3. External Power Status
    Status| Meaning
    ---|---
    Blue&Green Light Solidon 3s| Connected to External Power

Part II – Specification & Features

2.1 Product Specification

Item Specifications
Tracking GPS+BDS+LBS
Voltage 9-90V DC
Accuracy <10m (just for reference)
Battery 60mAh/3.7V lithium polymer battery
Current ≦5mA(Battery powered)
Temperature -20℃ to +35℃
Dimension 71.9 (L)30.2W) 12.9 (H) mm

2.2 Product Features

Functions Triggering Conditions
Power Off Alert Triggered by the Illegal wire cutting
Fall off Alert Triggered by the attitude of the equipment changes after the

terminal is installed to recognize the vehicle attitude
Remove Alert| when the device is removed
Low Battery Alert| Triggered an alarm when the voltage of external power or its own built-in battery current is low
Geo Fence Alert| Triggered an alarm when the terminal enters and exits the designated area
Overspeed Alert| When the vehicle’s speed is greater than the speed threshold within the set time

Part III – Product Installation

3.1 Device Installation

  1. Check Device
    Confirm whether the appearance of the equipment is good and whether the relevant accessories are complete.

3.2 Wiring Diagram

  1. Use a multimeter to find the battery positive and negative power leads

  2. Use a multimeter to find the ACC line, the judgment method:
    The red pen of the multimeter is connected to the ACC line, and the black pen is connected to the negative electrode. When the motorcycle key is in the OFF state, the voltage is 0V. When the motorcycle key is turned ON, the multimeter displays Motorcycle power supply voltage;

  3. The terminal is equipped with the red wire (positive pole) of the power cord and the positive pole of the motorcycle battery;

  4. Insert the connector as shown above.lncoon JM C21 GNSS Vehicle Terminal - connector

3.3 Electric Vehicle Installation Position

lncoon JM C21 GNSS Vehicle Terminal - Electric Vehicle

3.4 Motorcycle Installation Position

lncoon JM C21 GNSS Vehicle Terminal - Motorcycle Installation
Position

Note: the satellites signal will greatly degrade if be installed under the driver

lncoon JM C21 GNSS Vehicle Terminal - satellites
signal

3.5 Car Installation Position

lncoon JM C21 GNSS Vehicle Terminal - Car Installation
Position

Note: The device should be installed face up to the sky. If the windshield is pasted with a metal thermal insulation layer or a heating layer, it will reduce the signal strength of the satellite, which may make it difficult to locate the satellite. Please change the installation location.

Part V – Platform Operation

5.1 Register & Login into Platform
Login Lncoon platform(us.lncoon.com) with your account and password and check whether the location is correct on it. If not, please take your device to OPEN SKY for better signal intensity.

lncoon JM C21 GNSS Vehicle Terminal - Login into
Platformhttps://lncoon.com/download-app

5.1 Bundle Device with Platform

lncoon JM C21 GNSS Vehicle Terminal - Bundle Device

Attention: If the activation is not successful, please check if you have successfully subscribed to the plan, or check if the power switch is turned on.

Part VI – Troubleshooting

Problem Solution
Unable to add device Check your IMEI number

Check your account region
The device is offline on the platform| Check the external power cable.
Check your subscription status
Try find better cellular signals
Unable to Locate| Go to open sky area and try again
Try find better cellular signals
Location Drifts| Check that the cables are well connected
Go to the open area and try again
Not responding to commands| Check command format
Check if the device is online
Check if parameters are within limits

Caution:
Intended for sale and application in a business environment.
Use the Product in the environment with the temperature Between -20℃ and 35 ℃; Otherwise, it may damage your product. Products can only be used below 2000m altitude
For the following equipment:
Product Name: GNSS Vehicle Terminal
Brand Name: JIMI
Model No.: JM-C21
Shenzhen Jimi IOT Co., Ltd
E-mail: xieyi@jimilab.com
hereby declares that this [Name: GNSS Vehicle Terminal, Model: JM-C21] is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.


This product is intended for sale and application in a business environment.
RED Article 10 2
-This product can be used across EU member states
RED Article 10 10
-The product is class 1 product, No restrictions
The RF distance between body and product is 20cm
2G
Frequency Range: GPRS900: Tx: 880-915MHz, Rx: 925-960MHz
RF Output Power: GPRS900: 31.96dBm, GPRS1800: 29.08dBm
GPS
Frequency Range: 1575.42MHz Receiving

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Email: Support@lncoon.com
Website: www.lncoon.com
Tracking Platform: Lncoon App lncoon JM C21
GNSS Vehicle Terminal - Qr Codehttps://lncoon.com/download-app
@Lncoon
@lncoon.gps
+86 13423860204

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals