Party 10-5590PLS Illuminated Bluetooth Speaker User Manual
- June 16, 2024
- Party
Table of Contents
User Manual
REF. PARTY-OWL
Code: 10-5590PLS
ILLUMINATED BLUETOOTH SPEAKER
with BT, USB, microSD & LED
PRODUCT DESCRIPTION
EXPLANATION OF SIGNS
Accordance with the requirements of UK standard
The product is for indoor use only
**** This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmental safe recycling.
CHARGING THE BUILT-IN BATTERY’
Prior to using the speaker for the first time, fully charge the built-in
battery via the supplied USB lead (type-C connector). The charging voltage and
current are 5V 0.3A, maximum 5V 1A.
During charge, the speaker lights up in red. The red light goes off when the
battery is fully charged.
IMPORTANT NOTE FOR APPLIANCES CONTAINING LITHIUM-ION BATTERIES
- PRIOR to using the unit for the first time, please charge fully the battery
- Charge the battery regularly after each use. Don’t wait until it is discharged!
- DON’T allow the battery to discharge completely, otherwise it will lose 20% of its capacity or even be totally damaged! If the voltage becomes too low, the internal circuits are not powered anymore and it will become impossible to recharge the battery!
- If you don’t use the unit for a longer period of time, it is recommended to charge it at 40% of its capacity and check/charge it once per month.
The lifetime of the battery depends on the observance of these
recommendations.
BATTERIES ARE NOT COVERED BY THE WARRANTY
We cannot be held responsible for damaged batteries further to the non-
observance of these basic rules.
POWER ON/OFF (8)
Push switch (8) to ON position to switch the speaker on. The lights will be
flashing blue.
Push the switch to OFF position to switch the speaker off.
BLUETOOTH CONNECTION
Turn the speaker on. Activate the Bluetooth function on your mobile phone,
search for PARTY-OWL and connect.
When you switch on the speaker next time, it will automatically connect to the
last paired Bluetooth device.
PLAYING MUSIC
During play, press the PLAY/PAUSE button (2) to pause the music. Press again
to resume play.
During play, press “-“ button (3) to play the previous song or “+” (1) to play
the next song.
Keep “-“ button pressed to decrease the volume.
Keep “+” button pressed to increase the volume.
LIGHT SWITCH (4)
Press to toggle through the various light modes and OFF.
MUSIC SOURCE SELECTION
When the speaker is switched on, it enters automatically into Bluetooth mode.
Insert a microSD card, a USB
stick or connect an AUX device and playback of the connected device will start
automatically.
SPECIFICATIONS
Speakers ……………………………………………………………………………………………………………………….. 2 x 52mm
Power ………………………………………………………………………………………………………………………………… 2 x 7W
Frequency range …………………………………………………………………………………………………………90Hz – 20kHz
Power supply ……………………………………………………………………………………… 5V? 1A via USB ‘C’ type cable
Built-in battery ……………………………………………………………………………………………………… 3.7V ****1800mAh
Bluetooth freq. range ……………………………………………………………………………………………… 2402 – 2480MHz
Max. RF emission of BT …………………………………………………………………………………………………….. -6.03dBm
Dimensions ……………………………………………………………………………………………………….. 196 x 67 x 103mm
Weight…………………………………………………………………………………………………………………………………. 0.6kg
EU Declaration of Conformity
Hereby we,
LOTRONIC SA
Avenue Zénobe Gramme, 9
1480 SAINTES
Belgique
+32.2.390.91.91
Certify and declare under our sole responsibility that the following product:
Trade name: PARTY
Product name: BLUETOOTH SPEAKER
Type or model: PARTY-OWL
Conforms to the essential requirements of the RED directive 2014/53/EU,
2011/65/EU RoHS directive, the Commission Delegated Directive (EU) 2015/863
and the battery directive 2006/66/EC, based on the following specifications
applied:
EN IEC 62368-1 : 2020 + A11 : 2020
EN 50663 : 2017
EN 62479 : 2010
ETSI EN 301 489-1 V2.2.3 : 2019-11
ETSI EN 301 489-17 V3.2.4 : 2020-09
EN 55032 : 2015 + A11 : 2020
EN 55035 : 2017 + A11 : 2020
EN 61000-3-2 : 2019
EN 61000-3-3 : 2013 + A1 : 2019
ETSI EN 300 328 V2.2.2 : 2019-07
IEC 62133-2 : 2017
IEC 62321-3-1 : 2013
IEC 62321-4 : 2013 + AMD1 : 2017
IEC 62321-5 : 2013
IEC 62321-6 : 2015
IEC 62321-7-1 : 2015
IEC 62321-7-2 : 2017
IEC 62321-8 : 2017
Place and date of issue:
Saintes ( Belgium ), on 20/03/2023
Manuel De Sousa
Quality Manager