FM4545 Single Monitor Arm Stand

Product Information

Specifications

• Model: FM4545
• Compatible VESA patterns: 7575mm, 100100mm
• Maximum Weight Capacity: 26.4 lbs (12 kg)

Product Usage Instructions

Important Safety Information

Read the entire instruction manual before you start installation
and assembly. If you have any questions regarding any of the
instructions or warnings, please contact us via email at
forgingmount888@163.com.

Packing List

• A – Mounting Bracket
• B – Clamp Base
• C – Grommet Base
• D – Screws and Allen Key

Installation Method 1: Clamp Installation

1. Attach the clamp base (B) to the edge of your desk using screws
   (D).

2. Position the mounting bracket (A) onto the clamp base (B).

3. Tighten the screws (D) to secure the mounting bracket (A) onto
   the clamp base (B).

Installation Method 2: Grommet Base Installation

1. Create a hole in your desk according to the specified
   dimensions (0.39-1.97 inches or 10-50mm).

2. Insert the grommet base (C) into the hole.

3. Position the mounting bracket (A) onto the grommet base
   (C).

4. Tighten the screws (D) to secure the mounting bracket (A) onto
   the grommet base (C).

Connect with Monitor

Use a wrench (G) to screw the screws (A/B) into the four holes
at the back of the monitor to avoid damaging the monitor by over
tightening the screws.

Case 1: Monitor/Arm Fall Down (After Installing Your

Monitor)

Press the arm to make it keep it in a horizontal position and
then use the Allen Key to adjust the screw on the arm. Turn
counter-clockwise (+ direction) to increase gas spring tension
until it can hold the weight of your monitor.

Case 2: Monitor/Arm Pops Up (After Installing Your

Monitor)

Press the arm to make it keep it in a horizontal position and
then use the Allen Key to adjust the screw on the arm. Turn
clockwise (- direction) to reduce gas spring tension until it can
stay in the desired position.

Adjustment

To adjust the flexibility of the mount, turn the wrench
clockwise to tighten or counterclockwise to loosen.

Limit Screw

The limit screw can prevent the head from sinking. It can also
be disassembled if necessary.

Cable Management

Arrange and organize your cables using the cable management
system provided with the product.

Adjustable Instruction

Refer to the adjustable instruction manual for detailed
information on customizing your monitor’s position and angle.

FAQ

Q: What is the maximum weight capacity of this monitor desk

mount?

A: The maximum weight capacity of this monitor desk mount is
26.4 lbs (12 kg).

Q: Can I use this mount with monitors larger than 26.4

lbs?

A: No, this mounting system is intended for use only with the
maximum weights indicated. Using it with products heavier than the
recommended weight may result in failure of the mount and its
accessories, causing possible damage and/or injury.

Q: How often should I check the bracket for security and

safety?

A: It is recommended to check that the bracket is secure and
safe to use at least every three months.

Q: What should I do if any parts are missing or faulty?

A: If any parts are missing or faulty, please contact us via
email at forgingmount888@163.com.

MONITOR DESK MOUNT
INSTALLATION MANUAL

ModelFM4545
Thanks for choosing our product! We strive to provide the best quality and services for our customers. Would you kindly share your experience on Amazon if you are satisfied? If you have any questions, please feel free contact us.
Email: forgingmount888@163.com
We’re ready to help!

7575mm 100100mm

36″ MAX

26.4LBS MAX
1

IMPORTANT SAFETY INFORMATION Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact US via: forgingmount888@163.com
BE CAREFUL CAUTION: Exceeding the weight capacity can result in serious personal injury or damage to equipment! 1. Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury. 2. Safety gear and proper tools must be used. This product should only be installed by professionals. 3. Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components. 4. Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws. 5. This product contains small items that could be a choking hazard if swallowed. Keep these items away from children. 6. This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, can contact us via: forgingmount888@163.com.
MAINTENANCE: Check that the bracket is secure and safe to use at regular intervals. (at least every three months)

WEIGHT RESTRICTIONS

WARNING

4-26.4LBS 2-12kg
Holds up to

DO NOT exceed the maximum weight indicated. This mounting system is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage and or injury.

2

PACKING LIST

1×1 Base

2×1 Clip Plate

3×1 Long Bolt

4×1 Clamp

5×1 Bracket

6×1 Lower Arm

7×1 Upper Arm

8×1 VESA Plate

9×1 Cable Cover

10×1 Anti-slip Pad

M4×10×4 M5×10×4 M8×20×1 M6×10×2

A

B

C

D

3MM×1 E

4MM×1 F

5MM×1 G

3

Installation Method 1 Clamp Installation

1a-1

1a-2 1

1a-3a F
D

C
G 5

1a-3b

F

4

D

0.39″-1.97″ (10-50mm)
1.18″-3.15″ (30-80mm)

10 4

1a-4

4

Installation Method 2 Grommet Base Installation
1b-1 1
10 1b-2
2 3
G
2
E
5

3 Connect with Monitor
Use a wrench (G) to screw the screws (A/B) into the four holes at the back of the monitor to avoid damaging the monitor by over tightening the screws.
G A/B
4

When the display is inserted into the quick release head, make sure the knob is vertical.

After insertion, rotate the knob 90 degrees to the left.
6

5-1

Case 1Monitor/Arm Fall Down (After Install Your Monitor)

Press the arm to make it keep it in horizontal position and then use the Allen Key to adjust the screw on the arm.Turn counter-clockwise(“+ ” direction) to increase gas spring tension till can hold the weight of your monitor.

Note: You may need to turn the screw by many circles to tighten the arm.

G

fall down

5-2

Case 2Monitor/Arm Pops Up (After Install Your Monitor)

Press the arm to make it keep it in horizontal position and then use the Allen Key to adjust the screw on the arm.Turn clockwise(“- ” direction) to reduce gas spring tension till can stay the position needed.

Note: You may need to turn the screw by many circles to tighten the arm.

G

pop up

7

Adjustment

6

Adjust Flexiblity

G
Turn clockwise to tighten

– Turn counterclockwise to loose
6

If the pitching angle too tight or too loose when adjusting the mount, please adjust the screw

7

Limit Screw

This limit screw can prevent
the head from sinking. It can
also be disassembled if necessary

8

8

Cable Management

9

Adjustable Instruction

180° 360°

+90° -45°

360°

360°

9

Thank you again
for choosing this forgingmount product!
10

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>