HiQuick HQ-6823 8 Bay Smart Battery Charger User Manual
- June 14, 2024
- HiQuick
Table of Contents
High Quick & Performance!
HQ-6823 8 Bay Smart Battery Charger
User Manual
HQ-6823 8 Bay Smart Battery Charger
Thanks for purchasing HI Quick’s products!
For your own safety, please read this user manual carefully before using it.
■ User Manual
Specifications
Input: Micro USB DC5V 2A Min
Output: AA &AAA 1.2VDC 600mA±10%
Battery Charging Rate: 280%
Charging Way: Constant voltage and current control
Features
- Independent slot charger, our charger can charge 1/2/3 ..7/8 of AN AAA Ni-MH and Ni-Cd rechargeable batteries. These two types of batteries can be charged at the same time.
- Fast charging: DC5V 2A fast charging input port, compatible with AN AAA Ni-MH and Ni-CD rechargeable battery, saving the long waiting time for charging.
- With advanced MCU control system, intelligent /V and -AV cut-off charging tech, the charger turns to trickle charging automatically to prevent the batteries from over-voltage, over-current and over-heat.
- Broken & alkaline batteries detection. The smart charger could identify batteries which are non-rechargeable, short-circuited or defective and switch off automatically to ensure safety.
- Low-voltage battery can be activated: even if the battery voltage is lower than 0.9V, the charger can activate and refresh it.
Working Environment Condition
-
Working Altitude: Below 2000M
-
Storage Temperature: -10C-50C
Storage Humidity: 45%-85% -
Working Temperature: 0’C-35C
Working Humidity: 35%-85% -
Surface Temperature in Charging:
Surface Temperature of Charger: 35C-60C
Surface Temperature of Battery: 25C-60C
How to Use
Micro USB cable plug in and power on:
The LED screen will light up for 0.5 sec, then go out.
Put rechargeable batteries in, the LED will show:
Red Light | Charging process |
---|---|
Green Light” | Fully charged |
Please note: If you put alkaline batteries or other non-rechargeable batteries into the charger, the incompatible batteries would stop charging when the voltage goes up.
Notices
- Please use the micro USB cable provided by HiQuick.
- Please connect 5V 2A adapter before installing batteries.
- lnstall batteries into the charger correctly by making sure the +/- pole of battery matches the +/- pole of the charger.
- The charger can charge each battery independently.
- The charger must be used at an operating temperature of 0-35 C.
- The absolute 0 Volt battery can not be charged with this charger.
- The charger is ONLY designed for AN AAA Ni-MH and Ni-Cd rechargeable batteries.
- New battery will reach its best performance after 3-5 times of charge-discharge cycles.
- Battery power will lose because of long-time storage, please charge the battery fully before using it again.
- Please cut off the power supply after the batteries are fully charged.
- lt’s normal that the battery becomes hot while charging. It will cool down to normal degree later, please feel free to use it.
Important Safety Instructions
- Turn off the charger and take the batteries out after charging is completed.
- DO NOT disassemble and reassemble the charger, or it may cause short-circuit.
- DO NOT charge batteries whose cover are damaged, or it may cause short circuit and a fire hazard.
- DO NOT charge non-rechargeable batteries or other types of batteries. It may cause battery leakage, battery explosion, personal injuries, and etc.
- DO NOT put anything on the charger while charging batteries, it will accumulate heat and then cause a fire hazard.
- DO NOT install the battery inversely, or it may cause short circuit or a fire hazard.
- Indoor use only, keep it away from direct sunlight or moist/high -temperature environment.
- Children should use this charger under adult’s supervision.
- Place this charger out of reach of children.
Size & Weight
Size: 1258528mm
Weight: 98g
Warranty
- We provide 30 days worry-free money back and one year limited warranty.
- Any problem, please feel free to contact us at service@ihiquick.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>