ELVITA EBH330S Portable Speaker User Manual

ELVITA EBH330S Portable Speaker

Thank you

for your trust and the purchase of our product. Make sure you have received an undamaged product.
If you do find transport damage, please contact the seller from which you purchased the product, or the regional warehouse from which it was supplied.

OVERVIEW

A. Increase volume (short press)
B. Next track (long press)
C. Decrease volume (short press)
D. Previous track (long press)
E. Indicator LED
F. Mode/Source (change EQ mode, change audio source)
G. Play/Pause
H. Power
I. Microphone
J. Battery level indicator
K. USB-C charging port
L. MicroSD card slot
M. AUX IN port
N. USB-C cable

SAFETY

Carefully read the instructions before you install and use the product. Save the instructions and keep them near the product for future reference. All kinds of warranties shall be invalid if these instructions are not followed.
The model code is printed on the product.

DANGER!

• This product contains a lithium-ion battery. If misused, opened or damaged, it can become a hazard and may explode.
• Do not attempt to burn the speakers. The battery could explode causing injury and death.

WARNING!

• Only charge with devices rated and marked with 5V to avoid damage to the speaker.
• When using the speaker, adjust the sound to a suitable level to avoid damaging the hearing of yourself and others.
• Before wiping off the speaker with a dry cloth, turn off the speaker and disconnect the charging cable from any power source.
• Do not drop, disassemble, bend, or puncture the speaker.
• Place the speaker in a stable position. If the speaker falls down this may cause damage or personal injury.
• Never place the speaker close to high temperature heat sources. Do not leave the product near any heat sources, such as radiators, heat registers, stoves or other appliances that produce heat.
• Do not attempt to repair or service the product yourself. Please contact the manufacturer to be referred to an authorized service center near you.

CAUTION!

• Do not open up the speaker, it may damage the product.
• Any changes or modifications of the speaker not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Disposal

| | DANGER!
This product contains a lithium-ion battery. If misused, opened or damaged, it can become a hazard and may explode.
---|---|---
| WARNING!
Dispose of the used battery according to your local waste disposal authority.

The European Directive for batteries 2006/66/EC states that it is not permitted to throw away batteries with household waste. They may contain substances which are harmful to the environment. Empty batteries can be handed over to local, public collection point or a local recycling centre.

Dispose of packaging in an environmentally-friendly manner. Recycling packaging, while observing national and local regulations, can reduce the consumption of raw materials and the amount of waste in landfill sites.
This product complies with international directives, including but not limited to WEEE Directive (2012/19/EU). The symbol on the product or on its packaging indicates that this product should not be treated as household waste. Consult your local waste disposal authority for guidance on how to properly recycle or dispose of this product.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact the relevant municipal body in charge of waste management, your household waste disposal service or the store where you purchased the product.

CONNECTING TO AN AUDIO SOURCE

You can connect the speaker via Bluetooth, microSD card, or audio cable.
Connect the speaker with Bluetooth
The speaker can be paired with 1 Bluetooth device at a time. If the speaker is already paired with a device, you must disconnect it before connecting to another device.
To pair the speaker with a device:

1. Ensure the speaker and the device are within 10 m of each other.
2. Ensure the speaker is turned on and that the indicator LED light flashes white.
3. On the device, search for Bluetooth devices.
4. In the list of Bluetooth devices, select your speaker’s model number EBH330S.
   When the pairing succeeds, you will hear an acoustic signal and the indicator LED light turns solid white.

Disconnect the speaker (Bluetooth)

1. Press and hold the Mode/Source button for 2 seconds until the indicator LED light turns off.

Reconnect the speaker (Bluetooth)
If a previously paired device supports automatic reconnection, the speaker will connect to it automatically. The speaker will not automatically connect to devices that do not support automatic reconnection.
To reconnect the last disconnected device:

1. If the speaker is not connected via Bluetooth: press and hold the Mode/Source button for 2 seconds, until the indicator LED light turns solid white.

Clear all pairing information (Bluetooth)

1. Press and hold the Play/Pause button for 5 seconds, until you hear an acoustic signal and the speaker
   is turned off.

Connect the speaker to a microSD card

1. Ensure the speaker is turned off.
2. Connect a microSD card to the speaker’s microSD card slot.
3. Turn on the speaker.

Connect the speaker with an audio cable

1. Make sure the speaker is turned on.
2. Connect a 3.5 mm audio cable to the speaker’s AUX IN port.
3. Connect the other end of the cable to your audio source.

USING THE SPEAKER

Keep the battery healthy
The speaker is powered by a built-in, rechargeable lithium-ion battery. To ensure optimal performance, remember to charge the speaker at least every 3 months.
Note that a rechargeable battery’s lifespan and number of charge cycles depend on usage and settings.

Charge the speaker

1. Connect the USB-C cable to the speaker’s charging port.
2. Connect the other end of the USB cable to a certified USB power output.
   The number of lit battery level indicator lights indicate the charge level. When all 4 lights are lit, the battery is fully charged.

Turn on the speaker

1. If the speaker has not been used in 7 days or more: charge it for at least 10 minutes. If needed, you can
   continue charging the speaker while using it.

2. Press and hold the power button for 2 seconds.
   The indicator LED lits up.

Turn off the speaker

1. Press and hold the power button for 2 seconds, until the speaker is turned off.

Turn on or turn off the RGB light

1. Press the power button to turn on or turn off the RGB light.

Change the EQ mode
1. Press the Mode/Source button 2 times in quick succession to cycle between the EQ modes(standard,
bass, 3D).

Change audio source
If no LED is lit during playback, the current audio source is either Bluetooth or AUX. If the LED light flashes slowly,
the source is a microSD card.

1. Press the Mode/Source button to cycle between audio sources (Bluetooth, AUX, microSD card).

Change volume or track

• Increase volume: press the “+” button.
• Decrease volume: press the “-” button.
• Next track: press and hold the “+” button.
• Previous track: press and hold the “-” button.
• Increase volume in AUX mode: press and hold the “+” button.
• Decrease volume in AUX mode: press and hold the “-” button.

Use the speaker for hands-free phone calls
Hands-free functionality is available when connected to a mobile phone.

1. Connect your smartphone to the speaker via Bluetooth.
   The speaker will play your ringtone for any incoming call.

2. You can now do any of the following:

   • To reject an incoming call, press and hold the Play/Pause button for 2 seconds.
   • To answer an incoming call, press the Play/Pause button and then speak into the speaker’s microphone. Press the Play/Pause button again to hang up.
   • To return the last call, press the Play/Pause button 2 times in quick succession.

Connect two speakers for stereo sound (TWS, Bluetooth)
If you have 2 speakers of the same model, you can set up true wireless stereo (TWS):

1. Make sure the speakers are within 10 m of each other.

2. Turn on both speakers.

3. On one of the speakers, press and hold the Play/Pause button for 2 seconds, until you hear an acoustic signal

4. Wait a few seconds for the speakers to connect with each other.
   You will know they are connected when one speaker’s indicator LED flashes white every 3 seconds, while the other speaker’s indicator LED is a solid white.

5. Pair the primary speaker to your device: on the device, go to the Bluetooth settings, then search for Bluetooth devices, and then select your speaker’s model number in the list of Bluetooth devices.

The speaker flashing white every 3 seconds is the primary speaker and the left audio channel of the stereo, while the speaker with a solid white light is the right audio channel.

Disconnect TWS

1. On one of the speakers, press and hold the Play/Pause button for 2 seconds, until you hear an acoustic signal.

TROUBLESHOOTING

The speaker does not turn on Charge the speaker.
The speaker does not turn off or does not respond
Reset the speaker: press a thin needle into the AUX IN port to press the reset button.
The speaker does not turn off or does not respond Charge the speaker.
Cannot connect the device with the speaker

• If the indicator LED light is not lit, turn on the speaker. If the speaker does not turn on, charge the speaker.
• Too many Bluetooth devices near your device may make it difficult to find the speaker. Try removing or turning off some of the other devices.
• Turn on and turn off the speaker and try pairing again.
• If the speaker is connected to another device, disconnect it. You can force a disconnection by separating the speaker and the device more than 10 m.

The sound quality is poor / the sound stutters or break up

• Move the speaker and the audio source closer to each other (the Bluetooth range is around 10 m).
• Remove any obstacles between the speaker and the audio source.
• Ensure that both the speaker and the audio source have sufficient power.

I cannot hear any sound

• Adjust the volume.
• Move the speaker and the audio source closer to each other (the Bluetooth range is around 10 m).
• Remove any obstacles between the speaker and the audio source.
• Check if the audio source device and the speaker are paired. You can see this in the device’s Bluetooth settings.

TECHNICAL SPECIFICATIONS

Model EBH330S
Playing mode Bluetooth, AUX IN, microSD card
Working range 10 m
Bass speaker Ø 66 mm – 20 W
Tweeter speaker Ø 52 mm – 10 W
Impedance 4 Ω, 6 W × 2, 18 W × 1
Frequency response 20 Hz to 20 kHz
Total playtime 10 hours
Built-in rechargeable battery Li-ion, 7.2 V, 2500 mAh
Charging time 3,5 hours
Bluetooth version Version 5.0
Bluetooth chip BP1048B1
Bluetooth frequency range 2.402–2.480 GHz
Bluetooth transmit power +2 dBm
Input 5.0 V, 2.0 A
Dimensions (Ø × H) 94.5 × 224 mm
TWS pairing Yes
Weight 1000 g
Waterproof rating IPX7

References

• Köksvaror, vitvaror och elektronik för hela hemmet - Elvita

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>