ErGear EGESD32W Electric Standing Desk Instruction Manual

Electric Standing Desk
Instruction Manual
EGESD32w/EGESD33W/EGESD33N
Rev0O

****1-800-651-9525 (US/CA) Mon-Fri, 8am-8pm (CST)
44-808-196-3875 (UK) Mon-Fri, 2pm-10pm (UTC)
support@ergear.com
https://ergear.com

Specifications

Height Adjustment Range 28.3″-46.4″ (72-118cm)

Step 1
Supplied Parts and Hardware

Step 2 Supplied Parts and Hardware

Step 3 Supplied Parts and Hardware

Step 4 Supplied Parts and Hardware

Step 1 Assembling and Connecting the Desk Legs

Step2 Attaching the Side Plates and the Transmission Rod

Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level with the  right leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it.

Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg.

Secure the transmission rod to the motor drive shaft by turning the set screw clockwise.

Tighten the coupling nut to fine-tune transmission rod fit.

Step 3 Attaching the Desktop

Step 4 Connecting the Cables

NOTE: An example of a cable clip layout is indicated below. However, the cable clips can be arranged according to your needs.

Using the Controller

• Save Current Height Setting
  Short-press the M button. The display will flash. Press the ,1, 3 or 3 button to save the current height setting to that button.

• Select Height Setting 1
  Press the 1 button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 2
  Press the 2 button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 3
  Press the 3 button, and the desk will move to the height that was previously set for that button.

• Raise the Desk
  Press the + button to raise the desk continuously until it reaches the highest position of 46.4″ (118cm) or the button is released.

• Lower the Desk
  Press the – button to lower the desk continuously until it reaches the lowest position of 28.3″ (72cm) or the button is released.

Settings

Change Display
Height Units| Press and hold the M button until a flashing ‘S-‘is displayed.
Press M again, and ‘Un’ is displayed. Press M to select it, press + or – to switch between ‘IN’ (imperial) and ‘Sr’ (met­ ric), and press M to save your choice.
---|---
Change Collision
Detection Sensitivity| Long press the M button, ‘S-‘ shows and flashes. Press M again and the display shows ‘Un’. Press + or – to switch to ‘M’. Press + to – select. Press + or – to switch between ‘OFF’, Low (L), Normal (N) or  Heavy (H) collision force detection. Press M to save your choice.
Reset| Press and hold the – button for 5 seconds. The screen will
show ‘RES.’ Continue holding until the desk goes down to its
lowest level and comes back up slightly.

Protection Mode Error Codes

Hot| Overheating Protection: When the motor has been working continuously for 5 minutes, it will stop  operating to prevent damage from overheating. Wait for at least 15 minutes before making any  further height adjustment.
---|---
ElO| Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection  between the motor and controller, and power back on again.
E20| Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try  again. If lowering the desk, power off, take the things off the desk, power back on, and try again.
If error code persists, follow the reset instructions.
E02| Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this  detection is incorrect, follow the reset instructions before continuing use.
E32| Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E31| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the  desk, check the connection between power and the controller, and power on again.
E60| Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the  same height. Adjust if necessary by following the instructions. Power on again.
–| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation  should return once all connectors are properly connected.

Complete Flexibility
Total Freedom

Thank you for choosing this ErGear product. At ErGear we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us.

1-800-651-9525 (US/CA)
44-808-196-3875 (UK)
Mon-Fri, 8am-8pm (CST)
Mon-Fri, 2pm-10pm (UTC)
support@ergear.com
https://ergear.com
860-02286-00 Rev00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>