SUPERATV IN-FDGWS-CA-T Flip Down Glass Windshield Installation Guide
- June 16, 2024
- SUPERATV
Table of Contents
SUPERATV IN-FDGWS-CA-T Flip Down Glass Windshield
INSTALLATION INSTRUCTIONS
- SuperATV does not recommend keeping Windshield installed while transporting on an open air trailer. Remove or secure with straps.
- Do not discard packaging until product has been successfully installed.
When assembling, do not tighten hardware completely.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV’s® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact SuperATV® to verify that they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will
change the ride of machine
and may increase maintenance and part wear. Operating any off-road machine
while, or after, consuming alcohol and/or drugs increases risk of bodily harm
or death. No
warranty or representation is made as to this product’s ability to protect
user from severe injury or death. SuperATV® urges operators and occupants to
wear a helmet and
appropriate riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should
damages occur, SuperATV® will not be held responsible for loss of time, use,
labor fees, replacement
parts, or freight charges. SuperATV®, nor any 3rd party, will not be held
responsible for any direct, indirect, incidental, special, or consequential
damages that result from any
product purchased from SuperATV®. The total liability of seller to user for
all damages, losses, and causes of action, if any, shall not exceed the total
purchase price paid for the
product that gave rise to the claim.
SuperATV® will warranty only parts provided by SuperATV®. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered
by SuperATV®. SuperATV® parts and products are not warrantied if item was not
installed properly, misused, or modified. Installing, adding, modifying, or
fabricating any factory or aftermarket product to your ATV/UTV may violate
certain local, state, and federal laws. Be advised that laws vary depending on
town, city, county, state, etc. Use of certain products on public streets,
roads, or highways may be in violation law. The Buyer is solely and
exclusively legally and personally responsible for any violation of the law by
the installation or use of the product. You must abide by all local, state,
and federal laws, including but not limited to vehicle safety, traffic laws,
and ordinances. It is your responsibility to know the laws and how they apply
to you. The Buyer is responsible to fully understand the capability and
limitations of his/her vehicle according to manufacturer specifications,
warnings and instructions and agrees to hold SuperATV® harmless from any
damage resulting from failure to adhere to such specifications, warnings and/
or instructions. The Buyer is also responsible to obey all applicable federal,
state, and local laws and ordinances when operating his/her vehicle while
using this product, and the Buyer agrees to hold SuperATV® harmless from any
violation there of.
- Install Center Bracket to Lower with hardware shown; tighten.
To ease installation, soak 90° Seal in hot water before cutting or installing to increase flexibility.
- Install provided 90° Seal to Upper.
- Install Left Mount to Lower with hardware shown.
- Loosen Clamp and install Clamp to Left Mount with hardware shown.
- Repeat steps for Right Mount and Clamp installation.
- Install Lower to machine.
- Secure Clamps to Cage
- Install Gasket to Lower.
- Install Upper Mount to Upper with hardware shown.
- Repeat for opposite end of Upper.
- Install Upper to machine with hardware shown; tighten.
- Install Straps to Lower Bracket with the hardware shown; tighten.
- Install Bumpers to Lower Bracket.
- Install Lower Bracket to machine with stock or hardware shown below.
- Lower Bracket will go underneath plastic.
- Place Windshield onto Lower Bracket and machine.
- Secure Windshield to Hinges on Lower with hardware shown; tighten.
- Place Windshield into closed position, engage Latches and align to machine.
- TIGHTEN ALL HARDWARE
- Separate components shown from Wiper and assemble to Windshield; tighten.
- Install Wiper and Handle; tighten.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>