SUPERATV RZR XP Primal Soft Cab Enclosure Instruction Manual
- June 16, 2024
- SUPERATV
Table of Contents
2753 Michigan Road • Madison, Indiana 47250 •855-743-3427
RZR XP Primal Soft Cab Enclosure
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
Soft Cab Doors: for Polaris RZR XP® 1000 (2024)
Windows must be completely open when closing or opening Doors.
Notes:
– Hook and Loop Fasteners should be applied at a temperature of 70°F or above.
– Use Denatured Alcohol and thouroughly clean any area where Hook and Loop
Fasteners will be installed.
– Installing and adjusting Soft Cab is easier with two people.
– When cleaning Soft Cab, use soap and water only. Do not use detergent,
window cleaner, solvents.
– Do not use a dry cloth or rag on windows.
– Do not fold Soft Cab before storing. Zip windows closed and roll Soft Cab to
store.
– Do not discard packaging until product has been successfully installed.
– Doors may be secured with Snaps only, Hook and Loop Fastener only, or a
combination of Snaps and Hook and Loop Fastener.
– Any whiteness, clouding, wrinkles, or waves that develop will gradually
disappear when Soft Cab is exposed to sunlight and/or heat. Use a heat gun or
hair dryer to speed up this process. Do not overheat or heat in one area for
an extended period of time.
– Windows must be rolled up when trailering machine.
– Cut and secure Hook and Loop to Cage in locations shown.
– Repeat for opposite side.
– Place Soft Cab onto machine and loosely secure Straps.
– Align Soft Cab to machine.
– Cinch Straps tight.
– Secure all Flaps to Hook and Loop fastener.
– Repeat for opposite side.
HOOK AND LOOP TO BODY ONLY INSTALLATION:
(if Soft Cab is to be secured with Snaps, see “Snaps Installation”)
– Cut and secure Hook and Loop to flaps on lower inside portions of Door.
THESE STEPS MUST BE DONE FOR EACH INSTANCE
– Peel backing from Hook and Loop.
– Fold flap down and firmly press along areas where Hook and Loop is
installed.
wait 15 – 30 minutes for adhesive to setup
– Carefully open flap; use one hand to gently separate Hook and Loop Fastener
from flap and plastic while opening.
– Apply more heat to Hook and Loop. 
– Repeat for opposite side.
Snaps installation:
– Outline Snap with a paint marker, lipstick, or marker.
– To mark location, press Snap onto Body or Velcro.
– Install provided Snap.
– Secure Door to Snap.
– Repeat steps for remaining Snaps.– Repeat for opposite side.
Liability Statement SuperATV’s products are designed to best fit user’s
ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory
or aftermarket parts will void any warranty provided by SuperATV ® ® and is
not recommended. SuperATV’s products could interfere with other aftermarket
accessories. If user has aftermarket products on machine, contact SuperATV to
verify that they will work together.
Although SuperATV ® ® ® has thousands of satisfied customers, user should be
aware that installing lift kits, long travel, or suspension kits, tires, etc.
will change the ride of machine and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases risk of bodily harm or death. No warranty or representation is made
as to this product’s ability to protect user from severe injury or death.
SuperATV urges operators and occupants to wear a helmet and appropriate riding
gear at all times.
By purchasing and installing SuperATV ® products, user agrees that should
damages occur, SuperATV ® ® will not be held responsible for loss of time,
use, labor fees, replacement parts, or freight charges. SuperATV , nor any 3rd
party, will not be held responsible for any direct, indirect, incidental,
special, or consequential damages that result from any product purchased from
SuperATV ® ® . The total liability of seller to user for all damages, losses,
and causes of action, if any, shall not exceed the total purchase price paid
for the product that gave rise to the claim.
SuperATV ® will warranty only parts provided by SuperATV . Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered by SuperATV ® . SuperATV ® ® parts and products are not
warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws. Be
advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product. You
must abide by all local, state, and federal laws, including but not limited to
vehicle safety, traffic laws, and ordinances. It is your responsibility to
know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to hold SuperATV harmless from any damage resulting
from failure to adhere to such specifications, warnings and/ or instructions.
The Buyer is also responsible to obey all applicable federal, state, and local
laws and ordinances when operating his/her vehicle while using this product,
and the Buyer agrees to hold SuperATV ® harmless from any violation thereof.
Read instructions and view illustrations before beginning.
Thank You
For Choosing
IN-SE-P-RZR-001 9/13/2023
Need help with your installation?
sales@superatv.com
www.superatv.com
1-855-743-3427
8:00am – 8:00pm EST M-Th
8:00am – 7:00pm EST Friday
9:00am – 2:00pm EST Saturday
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>