SAUTER TVL-BA-e-2330 Series Test Stand TVL Compact Instruction Manual
- June 16, 2024
- SAUTER
Table of Contents
SAUTER TVL-BA-e-2330 Series Test Stand TVL Compact
Scope of delivery
- 1x manual test bench
- 1x hook for TVL, TVL-O, TVL-XLS (none for TVL-E)
Technical description
Technical data manual test stand
| TVL/TVL-O| TVL-XLS| TVL-E
---|---|---|---
Maximum force| 1000N| 500N| 2000N
Measuring direction| vertical and horizontal
Spindle stroke per revolution| 3mm| 2mm
Thread hook/load cell| M6| M12
Spindle height from base plate| 300mm| 350mm
Thread of the gauge mounting
plate
| 4x M3 (included in delivery)| –
Workspace| approx.
210mm
| approx.
450mm
| approx. 290mm
Weight| 8kg| 15kg| 9kg
Technical data of LA linear encoder (not for TVL-E and TVL-O)
| TVL| TVL-XLS| TVL-E/TVL-O
---|---|---|---
Scale length| 200mm| no length measuring device LA included in scope of
delivery
Readability| 0,01mm
Control buttons
On/0|
- Switch on
- Zeros of the display of the LA
mm/in| Change units between millimeter and
inch
▲| Manual length preselection, upwards
▼| Manual length preselection, downward
Optionally available for all test stands:
- LB-200 (Length measuring device with interface)
- LB-A02 (Attaching the linear encoder to the test stand)
- AFH FD (Software for force-displacement measurements)
Functional description
TVL/TVL-O/TVL-XLS
The TVL/TVL-O/TVL-XLS test stands are designed for force gauges with an
internal measuring cell up to 1 kN (for the maximum force of the respective
test stand, please refer to the table in the technical data).
The test stand should be set up on a solid base, such as a workbench or a base
plate.
A SAUTER force gauge can then be attached to the test stand using the four M3
cylinder head screws provided.
There are several holes in the base plate of the test stand for attaching
various accessories, such as clamps, linear encoders, etc. The handwheel can
be used to turn the test stand.
The test stand can be moved with a spindle stroke of 3mm/revolution via the
existing handwheel.
TVL-E
The TVL-E test stand is designed for force gauges with an external measuring
cell up to 2 kN. The test stand should be set up on a solid base, such as a
workbench or a base plate. The external measuring cell can then be attached to
the test stand via an M12 cylinder head screw.
There are several holes in the base plate of the test stand for attaching
various accessories, such as clamps, linear encoders, etc. The external
measuring cell can then be attached to the test stand via an M12 cylinder head
screw.
The test stand can be moved with a spindle stroke of 2mm/revolution via the
existing handwheel.
Maintenance
To prevent rust, the test stand should be cleaned with a lint-free, soft cloth
after each use.
Under no circumstances should aggressive cleaning agents be used.
General safety instructions
WARNING
Risk of injury due to overridden functions of the protective devices!
De-energized functions of the protective devices can lead to severe lead to
injuries.
- Never override the functions of the protective devices, neither you nor third parties.
- Never test with protective devices disabled.
- Never tamper with protective devices.
- Comply with all safety instructions.
WARNING
Risk of injury from falling parts!
Falling parts can cause serious injuries.
- Use only suitable and technically flawless lifting gear.
- Use lifting gear with sufficient lifting capacity.
- Carefully fasten individual parts and larger assemblies with lifting gear.
- Secure individual parts and larger assemblies with lifting gear.
- Make sure that no danger can emanate from the hoist.
- Lift individual parts and larger assemblies slowly.
WARNING
Risk of injury from rotating components! The drive can start automatically.
Rotating components such as spindles on the drive of the crosshead or the
extensometer can catch long hair, loose clothing and also sleeves or jewelry.
This can lead to serious injuries.
● Work only in clothing with tight-fitting sleeves.
● Wearing jewelry while working on the test system is prohibited.
● Use hairnet if necessary.
● Wear suitable protective equipment
WARNING
| Risk of injury when handling in the test chamber!
When handling in the test room during operation of the test system, there are
Risk of injury. Your hands and arms can be pinched and crushed.
- Never handle anything in the test chamber while the test system is running.
- Never handle anything in the test room during a test.
WARNING
| Danger of tipping due to the use of heavy specimens!
In the case of heavy specimens that are inserted off-center, as well as by
improper behavior can tip the test system.
● Ensure that the test system is securely positioned.
● Never use the test system as a climbing aid.
● Place the test stand on a stable surface.
CAUTION
Risk of injury!
There is a risk of injury when working on/with the test system.
- Comply with the applicable and binding national regulations on the accident prevention. Comply with the recognized technical regulations for safety and professional work.
- Comply with the regulations on safety and health protection during the Provision of work equipment and its use.
- Observe company regulations such as supervision and reporting requirements.
- Read the operating instructions completely.
- Read the operating instructions and data sheets of external components completely through.
- Observe all safety instructions in the operating manual.
- Observe all safety signs attached to the test system.
- Always wear appropriate safety equipment.
NOTE
Work on the test system may only be carried out by specialists qualified for this work. be carried out.
NOTE
Only one operator may work on the test system at a time.
CUSTOMER SUPPORT
Ziegler 1
D-72336 Balingian
E-mail: info@kern-sohn.com
Tel.: +49-[0]7433- 9933-0
Fax: +49-[0]7433-9933-149
Internet: www.sauter.eu
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>