LENSGO 348C Wireless Lavalier Microphone Instruction Manual

348C Wireless Lavalier Microphone
Instruction Manual

348C uses a 2.4G wireless microphone system. one-key operation. high-quality sound and stable performance. This product is suitable for various wireless applications such as interviews, news interviews (ENG), audio field production (EFP), film production, business and education, and other application scenarios.

Features

1. 2.4G wireless frequency, more widely used
2. Support stereo and mono mode switching
3. Built-in omnidirectional radio and television mic
4. Magnetic assembly method, convenient disassembly, and assembly, multiple usage methods
5. The operating range is up to 70 meters (face to face in an open environment, the recommended range is 30 meters)
6. The built-in lithium battery is charged by TYPE-C charging interface/box (there is no battery inside, it needs to be used with a charger)
7. Built-in TF card slot to prevent missing recording, maximum support 32G TF card
8. Transmitter (TX) one-button recording
9. Receiver (RX) hidden TFT screen

FCC Statement:

This device complies with Part 15 of the FCC Rules.
The operation meets the following two conditions:

1. This device will not cause harmful interference.
2. This device must accept any interference received, including interference that may cause an unexpected operation.

Warning: Only qualified maintenance personnel can install or repair this equipment.
Note: This device has been tested and complies with the requirements of Part 15 of the FCC Rules for Class B digital devices.

These limits are designed to provide reasonable protection against harmful interference in residential installations. This device generates radiofrequency radiation,lt it is not installed and used in accordance with the instructions, it may cause interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this device does cause interference to radio or television reception (by Turning off and turning on the device to confirm), it Is recommended that the user try to correct the interference by one or more of the following measures:

1. Re-adjust or reposition the receiving antenna.
2. Increase the distance between the interfered device and the receiver.
3. Adjust the interfered device to a frequency band different from the radio wave of the receiver.
4. Please consult the dealer or an experienced radio/TV technician for help.

Receiver (RX) 348C 1V1 of a transmitter (TX) and a receiver (RX) and its accessories 348C 1V2 of two transmitters (TX) and one receiver (RX) and its accessories

Listing as follows:

Transmitter (TX)

1. Windproof sponge hanging buttonhole

2. TF Card slot
   Maximum Support 32GB

3. TYPE-C Charging Interface

4. Power Indicator
   The blue light is always on for power indication, and the red light is flashing for low power indication

5. Signal indicator
   When the signal indicator is green, it means the pairing is successful

6. Recording button/recording indicator
   Start recording: Insert the TF card into the device card slot, and lightly press the REC button for three seconds. At this time, the red light flashes to indicate that the recording is turned on, and the RX device displays The red light flashes in the display; turn off the recording: when the recording is turned on, press the REC key for three seconds while the red light is flashing, and the red light is off, indicating The recording function is turned off. The red color disappears in the display of the RX device. When there is no TF card in the TX device, press the REC button, and the red light will be steady on

7. Power button
   Power on and off: press the power button for 1 second to turn on, long press for 1 second to turn off Mute: Press the power button for one second after powering on to start the mute mode. At this time, the blue light of the TX device will flash, and the RX device will display a quiet mute symbol

8. Box charging hole

9. Microphone

10. External microphone jack
    Insert an external microphone here to replace the transmitter source microphone for recording.

11. Removable magnetic cold shoe clip
    The cold shoe latch is a hot shoe latch for common recording equipment/recording accessories on the market.

Receiver (RX)

1. Volume +1- button
   +button microphone gain increase +3 total three gears, -button microphone gain decrease -3 total three gears
   Press and hold the +1- button at the same time to switch between S stereo sound/M mixing mode

2. Power Indicator
   The blue light is always on for power indication, and the red light is flashing for low power indication

3. Signal indicator
   When the signal indicator is green, it means the pairing is successful

4. Hidden TFT screen

5. Power button
   Power on and off press the power button for 1 second to turn on, long press for 3 seconds to turn off

6. TYPE-C charging interface

7. Boxed charging hole

8. Signal output hole

9. Removable magnetic cold shoe clip
   The cold shoe latch is a hot shoe latch for common recording equipment/recording accessories on the market.

Power on/Power off

1. Turn on the power, press the function button once, and the indicator light turns blue, which means a successful turn-on. (Please charge the device when it does not turn on when you press the function button of the device)
2. Turn off the power, press and hold the function button, when the indicator light is off, it means the boot is successful.

Card recording

Start recording: insert the TF card below 32G into the card slot of the device, gently press the REC key for 3 seconds, and then the red light flashes Indicate to start recording and red flashes in the display of the RX device; Close recording: the red light of REC button flashes when recording is started Long press the REC key for 3 seconds, and the red light will be off, indicating that the recording function has been turned off. The red color will disappear from the display of the RX device. If there is no TF card inserted in the TX device, press the REC key and the red light will always be on

Manual Channel Pairing

1V1 code pairing: when the power is off, press the TX power button for 8 seconds to enter the code pairing state, at this time the green signal light will flash quickly, and then press the power button for 8 seconds when the receiver (RX) is off. At this time the green signal light will quickly flash which means that the system is pairing. When the green signal lights of TX and RX are always on, it means that the pairing is successful. The interface will display the TX power.

1V2 code pairing: After one is successfully paired, turn off the paired TX and RX at the same time, and then press the power buttons of TX and RX which are needed to pair at the same time for 8 seconds, at this time the green signal lights of TX and RX will flash quickly, Indicates that the pairing is successful. and the RX interface will display the power of TX. Return on the TX. At this time, two groups of TX messages will be displayed on the screen to indicate successful pairing.

S Stereo Sound/M Mixing Function

Press the +/- button at the same time to switch between S stereo sound/M mixing mode
When the device is one for one, please use the M mixing mode,
When the device is one for two, you can freely switch to use

Connect Phone/Camera

1. Connect to smartphone
   Adapter Cable With Video Call
   Note: Apple phones support original camera recording, Android phones need third Fang camera recording, with OTG function can use mobile phone original equipment

2. Connect digital SLR cameras, camcorders, voice recorders
   

Connect To Laptop/Desktop

1. Connect Notebook
   

2. Connect To Desktop
   

How to use the collar clip

The collar clip can be used as a cold shoe latch.

1. Align the collar splint at the hot shoe port of the recording device or recording accessory, and insert it into the hot shoe port (the splint pin is commonly used in most hot shoe ports on the market).
2. After the concave position of the receiver magnet matches the convex position of the collar clip magnet, it can be plugged in and used.

Connect the charging box to charge

Please turn off the device before charging

1. Press the “PUSH” button to open the charging box

2. Put TX and RX into the charging box separately (please note that the probe should correspond to the pinhole of TX and RX, otherwise you cannot insert it)

3. Insert the TYPE-C charging cable, when the red indicator light of TX, RX flashes, it means it is charging
   

4. 4. When the product is fully charged, the red light is always on, indicating that the product is fully charged

5. After charging is completed, please unplug the TYPE-C charging cable

6. Close the charging box
   (Note: If the rechargeable indicator light shows other colors, please press the function button for 2 seconds to shut down the product)
   

Note: The box is unchangeable and needs to be used with a charger

Troubleshooting

If you encounter any problems with the 348C components, please use the following checklist.
If you still have problems, please consult your local dealer or contact us.

Output to device
No sound| 1. Whether the pairing is successful
2. The pairing is successful, there is no sound, speak into the TX microphone, check the RX reception Is their volume dynamics on the display
3. Change the phone line/camera line to confirm whether it is normal
4. Check whether the TX is muted, and observe whether the RX screen and the TX blue light flash
Too Many Ambient
Sounds Are Picked Up| 1. Make sure the microphone is as close as possible to the subject
2. Adjust the camera volume to 5 positions
3. RX volume adjustment
4. Wear Windproof Sponge
Noisy or distortion, Including electric current, Noise floor, Boom, etc.| Signal is disturbed
1. Try to record indoors, there is less radio frequency interference indoors.
2. Keep the transmitter and receiver away from conductive objects such as metal and water.
3. Overhead telephone lines, fluorescent lights, and metal fences will all cause interference to the wireless microphone.
4. Turn off all computers and mobile phones nearby.
Weak RF signal
1. Ensure that the line of sight between the transmitter and receiver antennas is unobstructed.
2. Your body, clothes, and stage scenery may cause obstacles.
3. Make sure the transmitter is within 50 meters of the receiver.
4. If there are obstacles, you may need to shorten the distance between the transmitter and the receiver.
The input level of the camera, video recorder, or mixer is too high. Turn down the camera or record The audio input level of the device. Reduce the audio output level on the receiver. Turn down The gain of the mixer. If there is no adjustment or setting function on the device, and the level is still high, you can adjust the output signal by adjusting the +/- key of RX.

Transmitter Parameters

contact charging / TYPE-C 5V charging port
Other functions| Recording function TFT HD display
Built-in battery life| About 7 hours 4H when the recording mode is on, 7H when the recording mode is not on
Antenna| FPC
Audio input source| 3.5mm microphone, built-in microphone
Size| 48’48mm
Weight| 40g
Operating temperature| 0°C-50°C
Storage temperature| -20`C—+55°C
Input frequency range| 40KHz-15KHz
RF output power| 12dBm
Total harmonic distortion| 0.03%
Voltage| 3.7V 400mAh
Power Consumption| TX unopened recording 180mW, open recording 440mW

Receiver Parameters

charging / TYPE-C 5V charging interface
Built-in battery life| About 8 hours
Antenna| FPC
Weight| 48’48mm
Size| 40g
Operating temperature| 0°C-50°C
Storage temperature| -20°C-+55°C
Total harmonic distortion| 0.03%
Signal to noise ratio| 90dB
Voltage| 3.7V 400mAh
Power Consumption| 280mW

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>