Temtop C10 Monitor Portable Carbon Dioxide Meter User Manual

C10 Air Quality Monitor
User Manual

Factory Affecting Air Quality

Carbon dioxide(CO2) refers to a colorless and odorless gas that is usually derived from the breath of humans and animals. High CO2 concentration means that fresh air or ventilation is required; otherwise, it may cause problems such as drowsiness, dizziness,loss of attention, and cognitive impairment.
Temperature & Humidity may often be ignored however they do have a significant impact on individual’s well-being, comfort, health and safety as well as your property. High humidity may lead to an increase in household air pollutants especially the biological contaminants such as molds, bacteria, viruses and dust mites; cold, low humidity may cause nosebleeds, skin and respiratory irritations, dyspnea, static electricity and etc.

Important!

★ Do not use the detector in a humid environment for a long time to ensure the measurement accuracy.
★ Do not use the detector for a long time in a strong irritating odor environment to ensure measurement accuracy.
★ Do not disassemble the device. In the event of a defect, please contact your dealer.
The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
★ Children should only use the device under adult supervision. Keep packaging material, like plastic bags and plastic film, out of the reach of children, as they pose a choking hazard.
★ This product is only used to monitor the health of the indoor environment and cannot be used as a professional measurement tool.

Overview

Specifications

Operation environment: -10-60°C (14-140°F)
0-90%RH
Temperature| Humidity
Measuring range: -20-70°C (-4-158°F)| Measuring range: 0-99%RH
Resolution: 0.1°C (-9.9-70°C)| Resolution: 1%RH
Accuracy: ±0.5°C| Accuracy: ±3%RH

Note: The above data are from Temtop Laboratory.

Operations

1. Turn On/ Off
Press and hold Home button for 2 seconds to turn on/ off the detector.
After start up, please wait for the countdowns.
Short press the Home button to switch the temperature unit (°C/°F).

2. Display
CO2, temperature and humidity will auto display after the countdowns.
Note:
Embedded sensor automatic control algorithm, taking into account the dynamic balance of data detection and product battery life, to provide users with a good experience!

3. Indicator Lights
The indicator lights on the panel indicate the corresponsing air quality(CO2):

The battery level indicator on the screen indicates the device charging status.

Note: The battery level indicator is only valid when the battery is powered off and charging.

4. Charging
When battery level is low, please by connecting it with the USB cable and power supply.
If it flashes , please charge the detector promptly to avoid effects during use (it can also be charged when it is turned off).
Note: When the battery is less than 5%, the charging symbol starts to flash.

5. CO2 Calibration
Turn on the detector in an outdoor ventilated place, use the pin tool to press and hold the calibration button for more than 3 seconds, after entering the calibration state, the CO2 title flashes on the screen, the CO2 display area starts to enter a 200-second countdown, and the countdown ends and the calibration is completed.

Note:

1. During manual calibration, the monitor must be exposed to fresh outdoor air (approximately 400 ppm of COz) at least 1 meter away from people.
2. During the calibration process, please ensure that the power supply is sufficient. If the calibration mode is forcibly exited due to shutdown or power failure, the calibration may fail and the data will be inaccurate, so you need to re-calibrate.

Air Quality Parameter for Reference

FAQ

Q:Why is the temperature high when charging？

A: The temperature and humidity sensor is located inside the product. When charging, a large amount of heat will be generated, causing the actual temperature of the product to rise.

Q:Why is CO2 data high？

A: The user's environment may be poorly ventilated, resulting in high CO2 concentration; it is recommended that the user place the product in an outdoor ventilated place for 10 minutes. If the data is still high, the customer is advised to calibrate according to the user manual.

What’s Included

Air Quality Detector x 1
C10 Manual x 1
USB Cable x 1
Pin Tool x 1

Warranty

Temtop warrants the included detector for 1 year from the date of original purchase.
The item can be exchanged or returned within 30 days if the defect is not caused by artificial damage.

Before return or delivery for repair, please check if the following items are ready:

| Detector & Accessories| Complete Package| **Proof of Purchase*| Gift (if any)**
---|---|---|---|---
Return| | | |
Exchange| | | |
Repair| | | |

• Including invoice, order number and etc.
  Temtop warranty does NOT include:

  • Malfunction or damages caused by artificial damage or modification.
  • Other deliberate damages.
  • Damage caused by natural events.

Elitech Technology, Inc.
2528 Qume Dr, Ste 2
San Jose, CA 95131 USA
Tel: (+1) 408-898-2866
Sales: sales@temtopus.com
Website: www.temtopus.com| Elitech (UK) Limited
Unit 13 Greenwich Business Park,
53 Norman Road,London, SE10 9QF
Tel: (+44)208-858-1888
Support: service@elitech.uk.com
Website: www.temtop.co.uk| Elitech Brazil Ltda
R.Dona Rosalina,90-Lgara, Canoas-RS
92410-695, Brazil
Tel: (+55)51-3939-8634
Sales: brasil@e-elitech.com
Website: www.elitechbrasil.com.br
---|---|---

Made in China

Documents / Resources

| Temtop C10 Monitor Portable Carbon Dioxide Meter [pdf] User Manual
C10, C10 Monitor Portable Carbon Dioxide Meter, Monitor Portable Carbon Dioxide Meter, Portable Carbon Dioxide Meter, Carbon Dioxide Meter, Dioxide Meter, Meter
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>