SPIDER PRO Camera Holster User Guide

PRODUCT INSTRUCTIONS

PRO Camera Holster

DSLR SINGLE
CAMERA SYSTEM v2
(1) SpiderPro Belt + Camera Holster
(1) DSLR Camera Plate

DSLR DUAL CAMERA SYSTEM v2

(1) SpiderPro Belt + Camera Holster
(1) Left Side Camera Pad + Camera Holster
(1) Lens Collar Plate v2
(2) DSLR Camera Plates

MIRRORLESS DUAL CAMERA SYSTEM v2

(1) SpiderPro Belt + Camera Holster
(1) Left Side Camera Pad + Camera Holster
(1) Lens Collar Plate v2
(2) Mirrorless Camera Plates

SPIDERPRO CAMERA HOLSTER

HOW TO USE THE HOLSTER LOCK

Rotate the lock levers up to remove your camera.
Keep rotating the lock-up until it clicks and the holster will remain unlocked.

DSLR CAMERA PLATE

DISCLAIMER:
WARNING! IMPROPER INSTALLATION AND USE OF THIS PRODUCT WILL VOID YOUR WARRANTY

MIRRORLESS CAMERA PLATE

ARCA SWISS COMPATIBILITY

The Spider Mirrorless Camera Plate has a built-in Arca Swiss tripod profile.
HOW TO:
INSTALL THE CAMERA PLATE TO A CAMERA THAT HAS THE TRIPOD MOUNT CLOSE TO THE BATTERY DOOR

1. Remove the bail screw from the sliding plate.
2. Slide out, rotate, and re-insert the slider plate.
3. Re-insert the slider and bail screw, and install the plate as shown, clearing the battery door.

HOW TO:
INSTALL CAMERA PLATE TO A LARGER-BODIED CAMERA

For small-bodied DSLR cameras and MIRRORLESS CAMERAS WITH BATTERY GRIPS, remove the two screws as shown.

LENS COLLAR PLATE V2

HOW TO:
INSTALL THE LENS COLLAR PLATE

Lens Collar Plate has an anti-rotation feature o keep it aligned with your lens and help prevent rotation.
*Lens Collar Plate’s RAISED FEATURE must be in contact with the back of the lens collar.
ARCA SWISS COMPATIBILITY

HOW TO:
PROPERLY USE THE SAFETY STOP SCREW
Use wrench to adjust as shown.
The SAFETY STOP SCREW will prevent the accidental sliding of the tripod plate from your Arca Swiss tripod.

BUILT-IN HEX WRENCH

The built-in Hex Wrench is used to install the plate to your camera.
TO REMOVE THE WRENCH:
PUSH IN AND ROTATE

UNIVERSAL TRIPOD COMPATIBILITY

SPIDER AS² Plate Arca Swiss)
SPIDER Arca Swiss + Manfrotto RC2 Plate
ANY Third Party Tripod Plate

Attach your  tripod plate to the universal 1/4”-20 connection on the Lens Collar Plate v2
USE WITH:
A CAMERA EQUIPPED WITH A VERTICAL GRIP
When operating with BOTH a DSLR Camera Plate and Lens Collar Plate along with a vertical grip, rotate your lens collar 90 degrees as shown.

We recommend using the Lens Collar Plate only when shooting with longer lenses.

SPIDERPRO CAMERA BELT

BELT SIZING

1. Peel apart the velcro webbing and adjust the size until it fits snugly on your hips.
2. Position the SLIDING CAMERA PAD so that it sits over your left hip. After, reconnecting the velcro webbing.

ADD THE SECOND CAMERA PAD

(DUAL CAMERA SYSTEM)

1. AFTER BELT SIZING:
   Be sure to position the belt padding over your right hip, this will be where you holster the second camera.

2. Slide the HOLSTER CLIP through the gap in the middle of the Sliding Camera Pad as shown.
   

BELT LOCK

To maximize security under all conditions, there are THREE locks on the belt buckle.

Press all three buttons at the same time to unlock.

WARRANTY INFORMATION

Spider Gear LLC., (”Spider Gear”) warrants these products against defects in material or workmanship for a period of (1) year from the original purchase of the product. Pursuant to this Limited Warranty, Spider Gear will, at its option, (i) repair the product using new or refurbished parts or (ii) replace the product with a new or refurbished product. In the event of a defect, these are your exclusive remedies. For purposes of this Limited warranty, “refurbished” means a product or part that has been returned to its original specifications. The warranty provided is for the repair or replacement of the product only.
Any parts or products replaced under this Limited
Warranty will become the property of Spider Gear.
LIMITATIONS ON DAMAGES:
Spider Gear shall not be liable for any direct, indirect, incidental, special, or consequential damages for breach of any express or implied warranty or contract or tort claim on this product. Our full warranty can be found at: https://www.spiderholster.com/policies/refund- policy
U.S. AND INTERNATIONAL PATENTS PENDING COPYRIGHT ©2021 SPIDER GEAR LLC.

SPIDER TRIPOD PLATES & ACCESSORIES

(AVAILABLE SEPARATELY)

Spider Adapter Plates can be mounted:

• Directly to the camera body
• On to the DSLR Camera Plate
• On to the Mirrorless Camera Plate

Tether Bail connection allows you to attach a SpiderWeb
Tether or security sling strap.

FOR TETHER USERS

SPIDER TETHER BAIL KIT

• Designed for the Spider Web Tether

• Compatible with Spider DSLR Camera Plate,
  Mirrorless Camera Plate, Lens Collar Plate

• Does not interfere with tripod use

• Compatible with sling-style camera straps

SPIDER TRIPOD PLATES

AS² TRIPOD ADAPTER PLATE

• Compatible with Arca Swiss-style tripods.

AS-RC2 TRIPOD ADAPTER PLATE
Compatible with:

• Arca Swiss-style tripods
• Manfrotto RC2 style tripods

TETHER CABLE ADAPTER PLATE

• Compatible with Arca Swiss-style tripods.
• Secures your tether cable to the camera
• Helps prevent expensive damage

References

• Refund policy – Spider Camera Holster

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>