FIELDMANN FZD 4010-E Electric Garden Shredder User Guide

FIELDMANN FZD 4010-E Electric Garden Shredder

Specifications

• Model: FZD 4010-E
• Noise Level: Complies with EN13683:2003 standard
• Machine Description:
  • Cover with a handle
  • Engine housing
  • Wheel with the cover
  • Chassis
  • Feed hopper
  • Shredder body
  • Discharge chute
  • Axle
  • Adjustment knob of the pressure plate cover
  • Main switch
  • Interlock switch (circuit breaker)

Product Usage Instructions

General Safety Instructions

Before using the garden shredder, please read and follow these general safety instructions:

• Unpack the product carefully and ensure all components are present.
• Keep the product in a dry place out of reach of children.
• Read all cautions and instructions to prevent accidents, fire, and serious injury.
• When handing over the machine to someone else, provide them with the manual.
• Adhere to the instructions for use, operation, maintenance, and repairs provided in the manual.

Explanation for Instruction Plates on the Machine

The instruction plates on the machine provide important information for safe operation.

Please take note of the following:

• Read the instructions carefully and familiarize yourself with the control elements and proper procedure for operating the machine.
• Keep hands, legs, hair, and clothes at a safe distance from moving parts of the shredder.
• Ensure bystanders are at a safe distance from the equipment to avoid potential hazards from objects thrown out of the shredder.
• Avoid the feed hopper or discharge area as the blade continues to rotate for 5 seconds after the machine has been stopped.
• If the cable is damaged, do not touch it. Disconnect the plug from the mains immediately, even if the equipment is not running or any work is being carried out on it.

Machine Description and Delivery Content

• Cover with a handle
• Engine housing
• Wheel with the cover
• Chassis
• Feed hopper
• Shredder body
• Discharge chute
• Axle
• Adjustment knob of the pressure plate cover
• Main switch
• Interlock switch (circuit breaker)
• Note: The maximum capacity of the machine is specified.
• The maximum thickness of a branch workable in this shredder is not provided as it depends on wood hardness.

FAQ

Q: Can I use the shredder in humid or rainy weather?

• A: No, do not use the shredder in humid or rainy weather. It should be protected against moisture.

Q: What safety gear should I wear when using the shredder?

• A: Always wear hearing protection, eye protection, and gloves when operating the shredder.

Q: How long does the blade continue to rotate after the machine has been stopped?

• A : The blade continues to rotate for 5 seconds after the machine has been stopped.
• Keep a safe distance from the feed hopper or discharge area during this time.
• Thank you for your purchase of our garden shredder.
• Before beginning to use it, please, read this operation manual carefully and keep it for the case of further use.

GENERAL SAFETY INSTRUCTIONS

Important safety warnings

• Unpack the product carefully and be sure not to throw away any part of the package before having found all components of the product.
• Keep the product in a dry place out of reach of children.
• Read all the cautions and instructions. Failure to adhere to warning cautions and instructions may result in an accident, fire, and/or serious injury.

Packaging

• The product is placed in a package preventing damage during transport. This package is a raw material therefore it can be handed over for recycling.

Instructions for use

• Before beginning to work with the machine, read the following safety rules and instructions for use. Familiarize with operating elements and the proper use of the device.
• Keep the manual in a safe place for future reference. We recommend keeping the original package including the inner packaging materials, cash voucher, and guarantee card for a period of warranty at a minimum.
• For a case of transportation, pack the machine into the original box from the manufacturer, thus ensuring maximum protection of the product during a possible transport (e.g. moving or sending into a service station).
• Note: If you hand the machine over to the next person, hand it over together with the manual. Adherence to the attached instructions for use is a precondition for the proper use of the machine.
• The operation manual includes also instructions for operation, maintenance, and repairs.
• The manufacturer does not take any responsibility for accidents or damages resulting from the failure to adhere to this manual.

EXPLANATION FOR INSTRUCTION PLATES ON THE MACHINE

• WARNING: Read the instructions carefully and be familiar with control elements and the proper procedure of the machine operation.
• WARNING: Keep hands, legs, hair, and clothes in a safe distance from moving parts of the shredder.
• Concerning the potential hazard of processed objects thrown out from the shredder, keep bystanders a safe distance away from the equipment.
• Keep yourself away from the feed hopper or discharge area! The blade rotates for 5 seconds after the machine has been stopped.
• WARNING: If the cable is damaged, do not touch it. Disconnect the plug from the mains immediately, and that even if: the equipment is not running or any work is being carried out on it (replacement of parts, repairs, adjustments, cleaning).
• WARNING: Always wear hearing protection, eye protection, and gloves.
• WARNING: Do not use the shredder in humid or rainy weather and protect it against moisture.

Noise level

• This equipment has been tested and has complied with the requirements of the EN13683:2003 standard see Appendix F.

POPIS STROJE A OBSAH DODÁVKY

Machine description (Fig.1,2,6)

1. Cover with a handle
2. Engine housing
3. Wheel with the cover
4. Chassis
5. Feed hopper
6. Shredder body
7. Discharge chute
8. Axle
9. Adjustment knob of the pressure plate cover
10. Main switch
11. Interlock switch (circuit breaker)

• Note: The above-mentioned specification characterizes the machine’s MAXIMUM CAPACITY.
• The maximum thickness of a branch workable in this shredder is not specified as it depends on wood hardness.

SAFE OPERATION PRINCIPLES

Advice

• Before beginning to work with this equipment, please, read the operation manual carefully.

Preparation for operation

• Do not allow children to operate the equipment.
• Do not use the machine near bystanders.
• Do not use the power supply cable if damaged. If any damage to the power supply cable occurs while working with the machine, do not touch the cable until disconnected from the power supply.
• The damaged cable might do serious harm to you.
• Always wear eye protection while operating the machine.
• Avoid wearing loose clothing with floppy strings, and ribbons.
• Use the equipment in an open area only (i.e. for example a safe distance away from walls and similar objects). Work only on a firm and level surface.
• Do not use the equipment on a paved or gravel surface where there is a risk of injury resulting from the processed material being ejected.
• Before starting the machine, check that all screws, bolts, nuts, and other fasteners are properly secured and protective components such as guards and screens are in place.
• Remove damaged or unreadable labels from the machine.

Operation

• Before starting the machine, make sure that the feeding chamber is empty.
• Keep your face and body away from the feed opening.
• Do not allow your hands or any other parts of your body or clothing to get near the feeding chamber (thereinafter feed hopper), discharge (thereinafter discharge chute), or near any other moving part of the machine.
• Do not lean over. Never stand at a higher level than the base of the machine when feeding material into the feed hopper.
• When operating this equipment, always stand clear of the discharge area, let us say the discharge chute.
• When feeding material into the shredder, be extremely careful that foreign objects as pieces of rocks, glass, metal, et al. are not included.
• If the shredding mechanism strikes any foreign object or if the machine starts making any unusual noise or vibration: stop the machine and disconnect it from the power supply.

Do the following steps:

• Check and tighten any loose moving components.
• Repair any damaged parts or replace them with new ones with corresponding properties. Do not allow processed material to build up in the discharge area; this may cause malfunction and can result in the kickback of material through the feed opening.
• If the machine gets jammed, switch off the drive unit before clearing a blockage. Do not allow processed material fragments to get into the unit, avoid its permanent damage or eventual ignition.
• Maintain all covers and deflectors in good condition and place.
• Never transport the equipment with the drive unit switched on.
• Whenever you leave the equipment, switch off the drive unit and disconnect from the power supply.
• Never incline the shredder while it is energized.
• Keep the extension cable(s) away from the shredding mechanism parts. Avoid their damage and a possible electrical shock hazard.

MAINTENANCE AND STORAGE

• If you intend to carry out a service inspection, storage, or replacement of some part, switch off the engine, disconnect the equipment from the mains, and make sure that all moving parts have been stopped.
• Before starting to carry out the planned activity, wait until the equipment cools down.
• Let the equipment cool down before storage.
• While carrying out any service maintenance of the shredding mechanism, do not forget that the mechanism can be switched on even manually despite of the interlock switch stop.
• Keep the ventilation slots of the engine cleaned – not only from the shredded material rests but also from all gathered garden debris – to reduce the fire risk.
• If for connecting the equipment to the mains the extension cable is used, it must not be lighter than the power supply cable belonging to the equipment.
• Check the power supply and extension cable condition regularly (if used) for signs of damage or wear. If there are any of them found, do not use the equipment.
• Never deactivate the interlock switch.

SAFETY MEASURES AND INSTRUCTIONS

WARNING! While using the electrical garden equipment, keep the preventive safety measures to reduce fire risk, electrical shock hazard, and damage to health.

IMPORTANT – Safety, health and living environment

• The necessary precondition for ensuring safety while using this electrical equipment is to be familiar with the principles of its safe operation and to follow them.
• Before beginning to use this product, read this operation manual carefully and keep it for the case of further use.

Before the first use of this product, read the instructions below and check whether:

• The power supply cable sheath is safely secured by a terminal.
• The extension cable sheath is not damaged.
• The cable(s) are/are led so that the risk of damage or accidental switch-off is eliminated.
• The power supply cable is unreeled from the coil completely so that not get overheated.

WARNING! Do not overlook it!

• When switching on the equipment supplied by alternating electric power, you may notice a short voltage drop.
• This drop may influence even other devices (for instance flickering of lights). However, if the alternating electric supply current impedance (Zmax) is less than 0.40 Ohm at 50Hz, there is no fear of this failure.
• Contact your local electricity supplier for more information.

Use an extension cable for outdoor applications

• When using the shredder outdoors, use only extension cables intended for outdoor applications for connecting to the mains.

Keep the working area clean!

• Mess and dirtiness may cause accidents.

Mind suitable working conditions

• Do not let the electrical equipment be subject to rain.
• Do not use the electrical equipment in rain or humid weather.
• The working area must be well-lit.
• Do not use the electrical equipment in a hazardous flammable or explosive atmosphere.

Protect yourself against electrical shock!

• Avoid physical contact with earthed objects, e.g. pipes, cables, etc.
• WARNING! Be careful about children and animals!
• Do not allow any comers to touch the machine or the extension cable. Keep all bystanders, particularly children and animals, away from the working area.

If not using the machine, store it!

• If not using the equipment, store it in a dry place out of the reach of children.

Use the proper tools!

• Do not use this electrical equipment for operations which it is not intended or designed for.

Wear suitable clothes!

• Avoid wearing loose clothes and jewelry while working with the shredder.
• The machine might catch them! While working with the equipment outdoors, wear gloves and non-slip shoes.
• Have long hair arranged and covered so that the machine cannot catch it.

Use protective equipment while working!

• Wear eye protection, a face-guard, or a special dust mask if needed when doing the planned activity. Wear hearing protection if working for a longer time or if carrying out a particularly noisy activity.

Additional hints

• For optimal fulfillment of the task, you need to choose an appropriate tool. Do not use an unsuitable tool for the demanded activity. Think better of what tool to use for what activity.

Hold tight!

• Use clamps or a vice for fixation of the tool.

Be careful of the power line!

• Make sure that the cable is attached properly and securely so as not to get disconnected, broken, or damaged in any other way, for instance as a result of inadequate loading.

Do not pull the power supply cable!

• Never handle the equipment by pulling the cable. Do not even try to disconnect it from the mains this way. Protect the cable against fire, oil, and sharp edges.

Keep the proper balance!

• Keep proper balance and footing at all times.

Maintain your tools!

• Maintain the shredding mechanism blade sharp and clean, thus you can enhance its performance. Be particular about lubrication and replacement of worn-out parts.
• Check the power supply cable regularly and in the case of need have it repaired in an authorized service station. Pay close attention also to the extension cable condition.
• Maintain the equipment handles dry, clean, and without rests of oils and greases.

Be always ready!

• Before the next use, you need to check or repair the safety stop or any other part that is damaged so that their proper function is ensured.
• Check functionality and adjustment of all moving parts of the machine and their components.
• If protective guards or any other elements with a similar purpose were damaged, let them be replaced in an authorized service station, unless otherwise specified in this manual.
• Let defective controls (switches) be replaced in an authorized service station as well. If they do not work properly, do not use the equipment.

Electric shock hazard!

• If not using the equipment or intending to carry out any repair or replacement of a defective component (for instance a blade), always switch it off and remove the plug out of the socket first!

Habit is stronger than reason!

• Before re-activating the machine after performing service work, make sure you have taken off just applied tools (wrenches, spanners, etc.).

Be alert!

• Do not move the equipment which is energized with your finger on the switch. Before connecting to the mains, make sure that the switch is in the off position.

Use common sense!

• Use common sense and do not use the equipment if you are e.g. tired at the moment!
• WARNING! Using components or parts not specified/recommended in this manual increases the risk of injury.

Contact a specialist!

• This electrical equipment conforms to the related safety requirements. Leave repairs to a competent specialist who uses original spare parts.
• In the opposite case you as the user are subject to a health hazard. Do not attempt to open the cover of the tool. A respective specialist is competent to replace the power supply cable.

Additional safety instructions

• The power source voltage must correspond to the voltage specified on the respective nameplate on the equipment.
• It is recommended to use the shredder with a protective switch of not more than 30 mA.
• Use only cables of a minimum weight of a cable with rubber insulation (H07RN-F type). If possible, when choosing the extension cable, choose bright (easily recognizable) colors for easier orientation.
• Use common sense! Think first, then act.
• Be careful the moment you start knives in the equipment.
• Do not use the cable for other purposes. Never use it as a towing device in terms of handling or as a “remote control” of the socket when disconnecting from the mains.
• Protect the cable against heat sources, oil, and sharp objects (beware of rough edges)! Place the cable and secure it so that it is not in the way, does not threaten, and cannot be damaged.
• Do not attempt to dismount the housing of the equipment. Do not attempt to modify the equipment.
• Only a specialist from an authorized service station can repair the power supply cable.
• Do not use the shredder if the cables are damaged or worn out.
• Do not connect the damaged cable to the mains. Do not touch the damaged cable if it is still connected to the mains. The damaged cable is alive and dangerous.
• Do not touch components of the shredding mechanism if the equipment is still connected to the mains and shredding knives have not been stopped completely yet.
• Keep the extension cable a safe distance away from the shredding mechanism. The mechanism blades might damage the cable and cause it to energize.

Remove the power supply cable plug from the socket:

• whenever you leave the equipment unattended for any period.
• before checking, cleaning, or service working on the equipment.
• after striking a foreign object, inspect the equipment for damage and make repairs as necessary.
• if the equipment starts to vibrate abnormally.

How to replace the electrical plug?

• If the plug is damaged and needs to be replaced, consult a skilled electrician.
• Never use the plug if it is damaged or not complete.

HOW TO ASSEMBLE THIS PRODUCT?

• Turn the machine upside down.
• Insert the chassis (4) into the body (6) (Fig. 4) and fix it with the attached screws. ****
• Put the axle (8) through openings in the chassis (4) (Fig. 3).
• Mount the wheels acc. to the drawing in (Fig. 5). ****
• a – wheel axle
• b – wheel
• c – cotter pin
• d – wheel cover
• Tighten the fixing screw of the blade head cover (9) (Fig. 2), equipped with an emergency switch
• Note: It is very dangerous to operate the shredder without a cover (1)

HOW TO USE THIS PRODUCT?

• Before using, make yourself familiar with the manual as well as the machine itself. Before any work on the machine, switch off the machine, remove the plug from the mains, and make sure that all moving parts have been stopped completely.
• Examine the material that you intend to process thoroughly first. Remove all foreign objects that might be ejected by the machine or get stuck in it during processing.
• Remove the earth from the roots. Do not put foreign objects such as stones, glass, pieces of metal, fibers, or plastic materials into the feed hopper! Shredding knives might be damaged.
• Always place the machine on a level and firm ground. While operating the shredder, do not lean over or make needless movements.
• Let the rotating knives of the shredding mechanism reach maximal revolutions and only then feed the material intended for shredding into the feed hopper.

Use the machine solely for shredding the following materials:

• twigs and branches (max. 40mm diameter)
• bush cleaning waste
• hedge cleaning waste
• rests of plants and other garden waste
• leaves and roots of plants (remove earth from roots before shredding)
• Do not feed soft kitchen bio-waste into the machine, put it on the compost heap.
• If not too bulky, insert the material for processing to the corner of the feed hopper. Knives will pull it inside without further assistance.
• Only insert as much material as can be fed into the feed opening so as not to get it jammed and blocked
• WARNING! Longer pieces of material may traverse about and strike you while being pulled into the shredding mechanism. Therefore keep a safe distance from the feed hopper!
• Ensure the shredded material comes freely out from the discharge chute.
• For better composting, you can process material in the shredder twice.
• Do not allow processed material to build up under the discharge chute so that it reaches the shredding mechanism. This would cause blockage of the knives and then of the feed hopper.
• Organic materials have high water and sap content which may cleave the equipment and clog it up. Therefore you should store it for a few days before shredding and let it dry up. However, above mentioned does not apply to bigger branches which can be optimally processed fresh.
• If the knives get stopped during shredding, stop the shredder immediately. Then disconnect it from the mains and start to search for the cause of the problem.
• Remove all processed material remaining from the blades of the knives; then inspect the knives thoroughly to be sure they have not been damaged. Only then go on in shredding.
• If the blade gets stopped for more than 5 seconds, the machine gets switched off through the overvoltage protection switch. Wait at least 1 minute and let the machine cool down before switching on the machine again.
• Then push the overvoltage protection switch and follow up the main switch (On/Off) to restart the machine.
• If the shredding mechanism blade strikes any foreign object or if the machine starts making any unusual noise or abnormal vibration, switch it off immediately and wait till the blade stops rotating and is still in place.

Remove the plug from the mains and then follow the procedure below:

• Inspect for damage.
• Replace or repair any damaged parts.
• Check for and tighten any parts loose because of the incident.
• If the equipment jams, switch off the machine and wait till the blade has been stopped. Before cleaning the equipment, disconnect the power supply/extension cable plug from the mains.
• Clean the engine ventilation slots from material remains and other debris; reduce the risk of engine damage and possible fire.
• Whenever you interrupt your work and leave the workplace, switch off the machine, wait till the shredding mechanism knives stop, and remove the power supply cable plug from the mains.
• Do not allow processed material to build up in the discharge area. By this, you eliminate the kickback risk that might occur through the feed hopper opening.

Switching on and stopping the shredder

• Use the main switch (10) to turn the shredder on and off (Fig. 2) – the ON position is marked with “I”, the OFF position with “O”.
• If the machine does not run, push the “interlock switch” (11) (Fig. 2), and make sure that the machine is connected (the power supply cable plug) to the mains.
• Let the machine engine run idle for several seconds and only then start shredding.

The interlock switch gets activated under the following circumstances:

• build-up of shredded material around the shredder roller.
• the engine capacity overload.
• processed material resists the shredder roller blades.
• If the interlock switch was activated, switch off the shredder and disconnect from the mains.
• Unscrew the control of the reamer at the bottom of the head and open the upper part.
• Remove the debris or obstacle from the shredding zone.
• Put the upper part back on and tighten the reamer control.
• Let the engine at a standstill for several minutes to cool down.
• Re-connect to the mains and push the interlock switch.
• To turn on the shredder again, press the main switch (10) (Fig. 2) – position “I”.
• WARNING! NEVER demount the pressure plate cover adjustment knob without switching off the main switch („On/Off“ button) and disconnecting the power supply cable plug from the mains first.
• WARNING! The shredder will stop shredding within 5 seconds after switching off by pushing the main switch.

The use of the plunger

• The plunger serves as an aid when filling the feed hopper with small materials (for instance small twigs, leafage, other garden waste, and greens).

Fill in the feed hopper (Fig. 6)

• Press the material through a plunger (12) (Fig. 7) towards the blade disk (Fig. 17).
• Wait until the material is shredded and only then insert the next batch.
• WARNING! Never allow your fingers inside the feed hopper chute!
• WARNING! Never use the equipment without the feed hopper!
• WARNING! Do not lean over the feed hopper!

How to collect the shredded material?

• Before moving the bag closer or farther, switch off the drive unit.
• For collecting the material, you can use the collection bag (if it is a part of delivery) or you can place the shredder on a sheet to collect the shredded material
• If you use the collection bag, you need to attach both hooks of the bag to the discharge chute.
• WARNING! Do not cover the ventilation slots of the machine body with the collection bag or shredded material.

What to do when replacing knives? (Fig. 8)

• Switch off the shredder and disconnect from the mains.
• Take off the upper part of the feed hopper assembly by unscrewing the adjustment knob of the pressure plate cover.
• The knives are double-sided. If the blade is worn out, it can be upturned and used by the other side.
• You should wear gloves while handling the knives to replace them.
• Arrest the shredder roller with the help of a hexagonal wrench (c).
• Unscrew both inner hexagonal nuts (b), and pay close attention to the knife cutting angle.
• Take off the knife and turn by 180 degrees (a); position the blade on the roller so that the bottom side points downwards.
• Follow the same procedure when replacing the other knife.
• If both blades of the knife are worn out, they must be replaced at the same time.
• They can be re-sharpened. (Sharpening must be carried out by a skilled specialist.)
• We do not recommend this solution concerning the fact that the absolute balance of the knives on the roller is highly important for the proper functionality of the machine.
• The slightest unbalance may result in damage to the machine or even injury to the operating person.

How to maintain the product?

• WARNING! Make sure the machine is disconnected from the mains while performing maintenance and cleaning.
• Before a service inspection, storage, or replacement of some part, switch off the engine and disconnect the equipment from the mains.
• If the extension cable is used, it must not be lighter than the power supply cable belonging to the equipment.
• Check the power supply cable and in case of need the used extension cable for signs of wear regularly. In the case of damage do not use the equipment.
• While carrying out any service maintenance of the shredding mechanism, do not forget that the mechanism can be switched on even manually despite of the interlock switch stop. Never deactivate the interlock switch.
• Remove dirtiness from the equipment with the help of a brush.
• Always clean the machine after each use. Use soap and a wet rag to clean the plastic parts. Do not use aggressive substances and solvents.
• Never clean the shredder by the water stream. Keep the equipment protected against water. Use the shredder only with recommended accessories.

TROUBLESHOOTING GUIDE

The machine does not work| a)  No power at the plug

b) The machine is switched off

c) The overload switch has tripped

d) The ejector chute is blocked

e)  Loading funnel is not secure

on the motor housing

| a)  Check the power cable and fuse

b)  Switch on the machine

c)  Press the control on the overload switch

b) Clean ejector chute

e) Clean interior and tighten safety screw

---|---|---
Shredding performance unsatisfactory| a) Blades worn| a) Turn, sharpen, or replace blades
Shredding performance falls in quality| a) Blades worn| a) Turn, sharpen, or replace blades

TECHNICAL DATA

• Model number ………………………………………………………………………………………………………………………… FZD 4010 E
• Rated voltage (V) ………………………………………………………………………………………………………………….. 230~ 50Hz
• Nominal input (W) ……………………………………………………………………………………………………………………………. 2400
• Idle   run speed (min-1) ……………………………………………………………………………………………………………………… 4500
• Max. cut thickness (mm) ……………………………………………………………………………………………………………………… 40
• Acoustic pressure dB(A) ……………………………………………………………………………………………………………………. 100
• Acoustic output dB(A) …………………………………………………………………………………………………………………………. 110
• Vibrations (m/s2) ……………………………………………………………………………………………………………………………… <2.5
• Net weight (kg) ……………………………………………………………………………………………………………………………………… 10
• Protection degree ……………………………………………………………………………………………………………………………….. IPX4
• The User’s Manual is in a specific language version.

DISPOSAL

• The machine and its accessories are made of various materials, e.g. metal and plastics.
• Hand over damaged components to sorted waste. Get yourselves informed by a respective authority.
• INSTRUCTIONS AND INFORMATION ON DISPOSAL OF USED PACKAGING.
• Put any used package material to the place determined by the municipality for waste disposal.

DISPOSAL OF USED ELECTRIC AND ELECTRONIC EQUIPMENT

• This symbol on products or accompanying documents means that used electric or electronic products must not be put into ordinary municipal waste.
• Hand over such products to determined collection points for proper disposal, restoration, and recycling. Alternatively, in some countries of the European Union or other European countries, you can return your products to your local dealer when you buy an equivalent new product. By dutiful disposal of this product, you can preserve precious natural resources and you help prevent any potential adverse effects on the environment and human health which could be the result of wrong waste disposal.
• Ask your local authority or the nearest collection point for additional details. In case of improper disposal of this waste, penalties can be imposed under national regulations.

For companies in the European Union countries

• Should you want to dispose of electric and electronic devices, ask your dealer or vendor for the necessary information.

Disposal in other countries outside the European Union

• Should you want to dispose of this product, ask your local authorities or your dealer for necessary information about the disposal method.
• This product fulfills all basic requirements of the EU directives that apply to it.
• Text, design, and technical specifications can change without prior notice and we reserve the right for their change.

DECLARATION OF CONFORMITY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>