RAB HIDFA-XXS-E6-8CCT-BYP Field Adjustable Post Top Instructions

RAB HIDFA-XXS-E6-8CCT-BYP Field Adjustable Post Top

RAB L1ght1ng 1s committed to creating h1gh-qual1ty affordable well-designed and energy-efficient LED l1ght1ng and controls that make 1t easy for electricians to install and end users to save energy Wed love to hear your comments Please call the Marketing Department at 888-RAB-1000 or email marketing@rablighting.com

HIDFA-XXS-E26-SCCT-BYP/SSP , HIDFA-XXXS-EX39-SCCT-BYP/SSP
Our optional sensors include MW-5/SMW-S, PIR-5/SPIR-S, DAYLIGHT-5, CONTROLJW/ AUX/5SP/LCB, CONTROL/WI AUX/SSP/LCBS and CONTROL/W/AUX/SSP/LCBS/MVS. The lamps will perform as normal if no sensor is inserted. If the lamps use CONTROL/W/AUX/SSP/LCB, CONTROLJW/ AUX/SSP/LCBS, and CONTROL/WI AUX/SSP/LCBS/MVS, please refer to sensor instructions to get setup and installation guide. Please note that RAB lamps can’t operate with other brand sensors.

IMPORTANT
READ CAREFULLY BEFORE INSTALLING LED HID BULBS. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB LED HID Bulbs must be wired by the National Electrical Code and all applicable codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED by THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNINGS:

• Main applications include for use in post top, street lights and other suitable light fixtures.
• Operating temperature:-30°C to 60°C (-22°F to 140°F).
• These LED Lamps require all ballasts, capacitors, and ignitors to be bypassed or removed. Do not operate lamps on existing ballasts.
• Dimmable with optional control modules.
• Do not use with standard dimmers. Only use the control provided with or specified by these instructions to control this lamp. This lamp will not operate properly when connected to a standard (incandescent) dimmer or dimming control.
• This device is not intended for use with emergency exits.
• Can be used in enclosed fixtures. Do not install 120W in horizontal applications.
• Before installation make certain the AC power to the fixture is off.
• Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for the installation of LED retrofit kit. Check for enclosed wiring and components.
• Risk of fire or electric shock. LED Retrofit lamp installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Installers should not disconnect existing wires from lamp holder terminals to make new connections at lamp holder terminals. Instead, installers should cut existing lamp holder leads away from the lamp holder and make new electrical connections to lamp holder lead wires by employing applicable connectors.
• To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
• Risk of fire or electric shock. Install this kit only in luminaires with the construction features and dimensions shown in the photographs or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
• Use only with a portable luminaire that is provided with a shade.
• The added weight of the device may cause instability of a free-standing portable luminaire.
• Text or diagram showing how the supply connections are made to the lamp holders.
• Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
• RISK OF FIRE OR ELECTRIC SHOCK. LUMINAIRES WIRING, POWER SUPPLY, OR OTHER ELECTRICAL PARTS MAY BE DAMAGED WHEN DRILLING FOR THE INSTALLATION OF RETROFIT KIT HARDWARE. INSPECT WIRING AND COMPONENTS FOR DAMAGE.
• THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION. PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN BY THE APPLICABLE AND APPROPRIATE ELECTRICAL CODES. THE INSTALLATION GUIDE DOES NOT SUPERSEDE LOCAL OR NATIONAL REGULATIONS FOR ELECTRICAL INSTALLATIONS.

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

LAMP INSTALLATION

1. Turn off the power before installation. Remove the old ballast or disconnect from the existing lamp holder. Shown as Figure 1. Remove and dispose of ballast correctly. (North America 100-2TNAC)
2. Reconnect directly to the existing lamp holder. Shown as Figure 2. (North America 100-277VAC)
3. Select the power and color temperature (CCT) of the new LED replacement lamp before installation.
4. Install a new LED replacement lamp. Shown in Figure 3. Please make sure the old fitting is correctly grounded. Attach the retrofit label to the luminaire. (North America 100-277VAC)

Securely fasten the ground wire to the main body structure. If the wire is damaged in any way please replace it. (Do not use existing burnt-out wire). If needed, the replacement ground wire must be 1.0mm in size and insulated from heat.

SELECTABILITY

Power and CCT Selectable

Note : These instructions do not cover If details or variations in equipment nor do they provide for every possible situation during installation, operation, or maintenance.

INSTRUCTIONS

Field Adjustable Post-Top

RAB Lighting 1s committed to creating h1gh-qual1ty affordable well-designed and energy-efficient LED l1ght1ng and controls that make it easy for electricians to install and end users to save energy Wed love to hear your comments Please call the Marketing Department at 888-RAB-1000 or email marketing@rablighting.com

SAFETY CABLE INSTALLATION INSTRUCTION

You must use the safety cable to secure the lamps equal to or over SOW in case of falling down due to old socket.

Easy Answers
rablighting.com Tech Help Line e-mail
Visit our website for product info Call our experts: 888 722-1000 Answered promptly – sales@rablighting.com
RAB WARRANTY : PAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty.

Free Lighting Layouts
Answered online or by request
RAB® 2023 RAB LIGHTING Inc. Cranbury, NewJersey08512USA. HIDFAPTSSP-IN-0123

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>