ARDESTO SHRR-B5WDR Electric Shaver Instruction Manual
- June 16, 2024
- ARDESTO
Table of Contents
ELECTRIC SHAVER
Instruction manual
SHRR-B5WDR
SAFETY WARNING
READ CAREFULLY AND STORE FOR FUTURE USE.
This appliance can be used by children over the age of 8 and people with
disabilities or lack of experience or knowledge, if they are under constant
supervision or have been instructed
in the safe use of the appliance and they understand the possible dangers.
Cleaning and customer service should not be performed by children without
supervision.
Children shall not play with the appliance.
Keep the product and its power cord out of reach of children under 8 yearsof
age.
The appliance must be powered only from a safe extra-low voltage according to
the marking on the appliance.
The cutting head of this appliance Can be washed under a water tap while
holding the shaver in your hand.
Warning! Always unplug the device before cleaning. Unplug the parts from
the power cord before cleaning them in water.
Attention: Use the device only with the supplied adapter to avoid a
dangerous situation.
- The electric shaver and its adapter can only be used indoors. Do not use the electric shaver outdoors.
- Do not place the adaptor over sharp objects. Make sure that the cable does not hang over the edge of a table or that it is not touching a heated surface.
- Ensure that the adaptor is not clamped or crimped.
- Keep the adaptor dry. Be careful not to get water on the adapter.
- Do not wind the adaptor around the handle of the appliance.
- Do not connect and disconnect the adaptor to and from the power source with wet hands.
- Before connecting the adaptor to a power source check that the voltage on its rating label corresponds to the voltage in the power socket to which you wish to connect it.
- Do not use the electric shaver or the adapter if it is damaged.
- If the device falls into water while charging, do not touch it and disconnect the adapter from the power source immediately. Contact an authorized service center to check the device.
Do not use or store the device at temperatures below 10 °C and above 50 °C.
Electrolyte leaking from a battery can be caused by overloading the appliance
or using it in extremely high temperatures. If battery fluid gets on the skin
or eyes, the affected area should be washed immediately with water. Seek
medical attention. The appliance is equipped with a built-in battery that can
only be removed at a professional service center. Never attempt to remove it
from the appliance yourself.
Attention!
Never disassemble the appliance for the purpose of removing the battery.
Never throw it into a fire. Incorrect use, risks releasing toxic substances or
causing a fire or explosion.
Safety during using:
-
This electric shaver is intended for home use only and is designed for shaving and trimming beards or whiskers and facial hair. The electric shaver is not intended for commercial purposes or for trimming animal fur.
-
This device belongs to personal hygiene items, so it should not be used by other people.
-
Do not leave the device switched on unattended.
-
When connected to the mains, do not use or store the electric shaver in areas where it may fall into water or be exposed to water jets/splashes.
-
We do not recommend using the electric shaver on parts of the face where there are open wounds or lacerations, burns, blisters, etc.
-
Use only the original accessories supplied with this electric shaver.
-
Do not use the electric shaver in rooms where aerosol sprayers are used or where oxygen is released.
-
Do not expose the electric shaver to the outdoor environment, extreme temperatures, direct sunlight, excessive humidity or excessively dusty environments.
-
Do not place the electric shaver near heaters, open fires or other sources of heat.
Warning: Keep the electric shaver dry. -
The electric shaver may heat up during use or when it is being charged. This is completely normal. Always turn off the electric shaver and disconnect it from the power socket when not using it, when leaving it without supervision, before cleaning, maintenance or storage. Store the electric shaver and its adaptor in a dry environment.
-
Keep the electric shaver clean. Do not perform any maintenance on the electric shaver other than cleaning the individual components as described in chapter Cleaning and maintenance.
-
Do not use the electric shaver if it has fallen, if it is not functioning correctly or if it is damaged in any other way. Contact an authorized service center. Do not attempt to repair the device yourself as this may void the warranty.
-
If the device has been stored or transported at low temperatures, keep the device at room temperature for 2 hours before use.
-
Check regularly, if the blades are not damaged or deformed.
-
If it is necessary to use an extension cord, it must be undamaged and meet current standards.
-
For additional protection we recommend installation of current protection (RCD) with the nominal release current not exceeding 30 mA. Ask a control technician or an electrician for advice.
-
Do not exceed the maximum continuous operation time of 30 minutes.
-
If the shaving part of the device is blocked, it is necessary to switch off the device immediately and eliminate the cause.
EQUIPMENT:
Electric shaver – 1 pc
Stand base – 1 pc
Protective cover – 1 pc
USB Type-C cable – 1 pc
Adaptor – 1 pc
Cleaning brush – 1 pc
Instruction manual (contains warranty card) – 1 pc
Use the device only as described in this instruction manual.
Keep the original packaging materials, receipt and warranty card during the
warranty period. If it is necessary to transport the device, we recommend
packing it in the original box.
PRODUCT OVERVIEW
DESCRIPTION OF THE ELECTRIC SHAVER AND ITS ACCESSORIES
A1 Cutters
A2 Shaving head with cutter holder
A3 On/Off switch
A4 Display
A5 Power cord connection socket
A6 Protective cover
A7 Adaptor
A8 Cleaning brush
A9 Stand base
B1 Setting indicator
B2 Cleaning indicator*
B3 Charging battery indicator
B4 Lock indicator
- After 10 minutes of use, it will start flashing for 10 seconds, thereby serving as a reminder.
PURPOSE OF USE
The electric shaver is intended for dry and wet shaving of beards and trimming
of sideburns, moustaches or facial hair. Dry shaving is recommended for best
results. The electric shaver is not intended for cutting synthetic hair or
animal fur.
The shaver is designed for household use and is not intended for commercial or
other professional use.
CHARGING
The electric shaver has a built-in battery that enables its cordless
operation. Before first use or after not using it for a long time, first allow
the electric shaver battery to fully charge.
The electric shaver can be charged in two ways:
- by means of an external device with a USB port (e.g. computer, USB hub, power bank, etc.).
- by means of a standard USB adapter connected to power socket.
Note: The selected power source must have an output of 5V DC.
Insert the smaller USB connector into the socket at the bottom of device and
the larger connector into the selected power source. The battery will start
charging when connected to an electrical power source. The current remaining
battery time will be lit on the display and the charging indicator B3 will be
lit.
The charging time differs depending on the current battery power level. If the
battery is completely discharged (flat), the charge may take up to 90 minutes.
When the battery is fully charged, the display B3 will be white light.
Disconnect the charged electric shaver from the electrical power source.
A fully charged battery will provide up to 45 minutes of cordless operation.
DIRECT DRIVE TECHNOLOGY
If the battery of the electric shaver is discharged (flat) or if it is
discharged during cordless operation, the shaver can be plugged into mains
power and can continue to be used. This is enabled by DIRECT DRIVE technology
used on the electric shaver. Therefore, no need to wait for a minimum charge.
Using the shaver connected to the mains is possible only with adapter
connection.
RECOMMENDATIONS FOR EXTENDING THE LIFETIME OF THE BATTERY
- In order for the built-in battery to serve you as long as possible, charge, use and store the electric shaver in a dry environment at an ambient temperature of 1535°C. Lower or higher temperatures have a negative impact on the lifespan of the battery.
- Do not wait for the battery to become completely flat. It is better to charge the battery before it is completely flat.
- When the electric shaver is not used for an extended period of time, charge it at least once every 6 months.
OPERATION / SHAVING
-
Turn on the electric shaver by pressing the switch A3.
-
Hold the electric shaver at a right angle to the skin surface and in short circular motions glide the shaving head over the skin on the face, moving against the growth direction of facial hair. Apply appropriate pressure to the skin. Do not push too hard.
-
While shaving, use your free hand to stretch the skin in hard-to-reach places, such as on the chin. In this way you will achieve better shaving results.
-
The shaver has two speed modes. To switch, press the A3 button for 2 seconds.
Note: It may take your skin and facial hair two to three weeks to become accustomed to the new way of shaving. During this period, we recommend using the electric shaver every day. -
When you have finished shaving, clean the electric shaver according to the instructions in chapter Cleaning and maintenance.
LOW BATTERY POWER INDICATION
When the remaining time shown on the display reaches 5 minutes or less,
battery level indicator B3 will start flashing on the display. If this
happens, plug it into mains power by adapter and continue using it.
SHAVING HEAD CLEANING INDICATOR
The shaver is equipped with a timer that adds up the operating time of the
shaver (shaving time). When it reaches 10 minutes, the symbol B2 will light up
to indicate and beeps will be made to remind that it is necessary to clean the
shaving head. If this happens, clean the shaver as soon as possible according
to chapter CLEANING THE SHAVING HEAD.
The next time you turn on the shaver, the timer will restart.
STAND-BY MODE
When the electric shaver is turned off using the On/Off switch A3 after use,
the display will remain lit for a few more seconds. The electric shaver will
then enter the standby mode in which the display turns off completely.
To wake the electric shaver from the stand-by mode, simply pick it up.
The display will be lit again. The electric shaver is thereby ready for
operation.
LOCK FUNCTION
The travel lock prevents the electric shaver from being turned on
accidentally, e.g. while travelling.
The travel lock is activated by pressing and holding down button A3 for 3
seconds. The beep will sound and the lock symbol B4 will be lit on the
display. The On/Off switch A3 does not react to being pressed.
To deactivate the travel lock, again press and hold down button A3 for 3
seconds. The lock symbol will turn off. Now the electric shaver is ready to
use again.
CLEANING AND MAINTENANCE
For hygiene reasons, clean the electric shaver after every use. Regular
cleaning is also important to ensure the correct operation of the electric
shaver and to extend the lifespan of the cutters.
Turn off the electric shaver before cleaning it. Never clean the electric
shaver when it is charging and connected to the power supply.
For cleaning, do not use brushes with hard bristles, cleaning products with an
abrasive effect, solvents, etc. Otherwise, the cleaned surface may be damaged.
CLEANING THE ELECTRIC SHAVER AND ADAPTER
The electric shaver unit can be cleaned using a clean dry cloth.
In the event that it is very dirty, you can use a lightly dampened cloth. Then
thoroughly wipe the cleaned surface dry. To clean the power cable and adapter,
use a clean, dry cloth.
CLEANING THE SHAVING HEAD
Cleaning with the brush, see fig. D
Use the brush to clean away all hair and whisker remains from the shaving
head. Pull upwards to remove the shaving head off the head holder, see fig. C.
Use the brush to remove dirt and any whiskers from the holder and the body of
the electric shaver. Put the shaving head back into the holder.
Cleaning with water
Warning: Do not wash the electric shaver with water or immerse it in
water while it is connected to the power supply.
Turn the electric shaver upside down and submerge the shaving head in water.
Turn on the electric shaver by pressing the switch A3 and allow it to run for
approximately 30 seconds. Then turn it off and take the head out of the water.
Using a fine cloth, dry the shaving head or allow it to dry naturally. Do not
use paper towels or coarse towels to dry it as this could damage the shaving
blades.
For a thorough clean, the shaving head can be removed by pulling on the
holder, see fig. E. Then wash both these parts under running water and allow
them to dry fully and then insert them back into the body of the electric
shaver.
STORAGE
When you have finished using it, you can store the electric shaver with all
its accessories in a suitable location out of children’s reach. Keep the
electric shaver away from extreme temperatures, direct sunlight and excessive
humidity. Do not use in an overly dusty environment.
The manufacturer reserves the right to make changes in the technical
characteristics and design of the products that do not impair the operational
qualities.
CORRECT DISPOSAL OF THIS PRODUCT
Never dispose of the device with normal household waste. Dispose of the device through an authorized disposal company or an appropriate government agency. Please follow all applicable rules. If in doubt, contact your waste disposal company. Your local community or municipal government can provide information on how to dispose of the product properly. A recyclable lithium battery powers this device. When the device reaches the end of its useful life, remove the battery from the device before disposing of it. Dispose of the battery in accordance with local waste disposal requirements. If you have questions about disposal, please contact your local waste disposal agency. The packaging is recyclable. Dispose of the packaging environmentally.
Warranty conditions:
The plant guarantees normal operation of the product within 12 months from
the date of the sale, provided that the consumer complies with the rules of
operation and care provided by this Manual. Service life of the product is 3
years. In order to avoid any misunderstanding we kindly ask you to carefully
study the Owner’s Manual, the terms of warranty, and check the correctness of
filling the Warranty Card. The Warranty Card is valid only if the following
information is correctly and clearly stated: model, serial number of the
product, date of sale, clear seals of the company-seller, signature of the
buyer. The model and serial number of the product must correspond to those
specified in the Warranty Card.
If these terms are violated, and if the information specified in the Warranty
Card is changed, erased or rewritten, the Warranty Card is considered invalid.
Setup and installation (assembly, connection, etc.) of the appliance are
described in the attached documentation; they can be carried out both by the
user, and by specialists having the necessary qualification sent by USC or
selling companies (on a paid basis). In this case, the person (the
institution) installing the appliance shall be responsible for the correctness
and quality of installation (setup). Please pay attention to the importance of
the correct installation of the appliance, both for its reliable operation,
and for obtaining warranty and free service. Require the installation
specialist to enter all the necessary information about the installation in
the Warranty Card. In case of failure of the appliance during the warranty
period by the fault of the manufacturer, the owner is entitled to free
warranty repair upon presentation of the correctly filled Warranty Card
together with the appliance in the factory configuration packed in the
original packaging to the warranty workshop or the place of its purchase.
Satisfaction of the customer’s claim due to the fault of the manufacturer
shall be made in accordance with the law «On Protection of Consumers’ Rights».
In the case of warranty repair the warranty period shall be extended for the
period of repair and shipment.
WARRANTY CARD
Dear Buyer! Congratulations on your purchase of the ARDESTO brand appliance,
which was designed and manufactured in accordance with the highest quality
standards, and we thank you for choosing this particular instrument.
We ask you to keep the coupon during the warranty period. When purchasing a
product, require a full warranty card.
-
Warranty service is carried out only if there is a correctly and clearly filled original warranty card, which indicates: product model, date of sale, serial number, warranty service period, and the seller’s seal. *
-
The service life of household appliances is 3 years.
-
The product is intended for consumer use. When using the product in commercial activities, the seller / manufacturer does not bear warranty obligations, after-sales service is performed on a paid basis.
-
Warranty repair is carried out within the period specified in the warranty card for the product in an authorized service center on the conditions and terms determined by applicable law.
-
The product is withdrawn from the warranty in case of violation by the consumer of the operating rules set forth in the instruction manual.
-
The product is removed from warranty service in the following cases:
• misuse and non-consumer use;
• mechanical damage;
• damage caused by the ingress of foreign objects, substances, liquids, insects;
• damage caused by natural disasters (rain, wind, lightning, etc.), fire, domestic factors (excessive humidity, dust, aggressive environment, etc.)
• damage caused by non-compliance of power and cable network parameters with state standards and other similar factors;
• when operating equipment in the power supply network with a missing single ground loop;
• in case of violation of seals installed on the product;
• lack of serial number of the device, or inability to identify it. -
The warranty does not cover consumables and accessories, as well as filters, shelves, drawers, stands and other containers for storing products.
-
The warranty period is 12 months from the date of sale.
- Tear-off maintenance tickets are provided by an authorized service center.
The completeness of the product is checked. I have read the terms of the
warranty service, no complaints.
Customer Signature ___
Warranty card
Product information…………………….
Product……………………………………….
Model
Serial number……………………………..
Seller Information……………………….
Trade organization name……………..
The address…………………………………
Date of sale………………………………….
Seller stamp………………………………..
Coupon 3
Seller stamp
Date of application
Cause of damage
Date of completion
Coupon 2
Seller stamp
Date of application
Cause of damage
Date of completion
Coupon 1
Seller stamp
Date of application
Cause of damage
Date of completion
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>