motogadget 7001010 Glassless Rear Mirror Instruction Manual
- June 16, 2024
- motogadget
Table of Contents
Instruction manual
mo.view
glassless rear mirror
7001010 Glassless Rear Mirror
Thank you very mutch for pruchasing a high quality motogadget product.
Made in Germany.
Please read the following information and recommendations thoroughly and
follow these in- structions during installations and use of the product. No
liability shall be assumde by motogadget for damage or defects resulting from
negligence or failure to follow the operating and installation guide.
Review of Delivery
Every motogadget product is delivered in perfect working order. Please check that the goods you receive have not been damaged in transit. If there is any damage or the packaging has been opened, please contact us immediately. Our general terms and conditions apply. If a return is agreed with us, please ensure that we only accept goods in their original packaging and without signs of use within the statutory periods. We accept no liability for returns that are inadequately insured or packaged.
Exclusion of Liability
THE DEVICE AND ITS ACCESSORIES MUST BE INSTALLED BY A CERTIFIED MOTORCYCLE TECHNICAN AND IN AN AUTHORIZED SERVICE CENTER. MOTOGADGET ACCEPTS NO LIABILITY FOR DIRECT OR INDIRECT DAMAGE OR SUBSEQUENT DAMAGE OF ANY KIND RESULTING FROM THE USE, INSTALLATION OR CONNECTION OF THE DEVICE OR OTHER DELIVERED EQUIPMENT. THIS EXCLUSION OF LIABILITY PARTICULARLY INCLUDES DA- MAGE TO PERSONS, MATERIAL LOSSES AND FINANCIAL DAMAGES. THE USE IN AREAS OF PUBLIC TRAFFIC ENSUES AT THE USER’S OWN RISK. THE USE OF THE DELIVERED DEVICE AND ITS ACCESSORIES FOR RACING OR OTHER COMPETITIONS AS WELL AS FOR ANY USE NOT CORRESPONDING TO THE RECOMMENDED APPLICATION ALL WARRANTY CLAIMS SHALL BE INVALID.
Features
motogadget mo.view mirrors are unique. They are made from one piece of aluminum and are un- breakable, super thin, frameless and many times lighter than conventional glass mirrors. The lower weight reduces the vibrations of the mirror and thus significantly improves the view. The reflecting surface is milled directly into the aluminum body by diamond cutting tools and then coated with a wafer-thin, glassy layer of silicon dioxide (SiO2). This coating is UV, weather and chemical and abrasion resistant. A object viewed in a glass mirror was reflected two times. First time at the glas surface and second time in the reflective coating at the bottom side of the glass plate. This is causing a slight unsharp image. Because a object viewed in a metal mirror is reflected only once, the visible image is sharper and apperas clearer.
Handling glassless mirrors
Despite the coating ensures abrasion resistance, glassless mirrors are more
sensitive than glass mirrors.
Contact with hard objects may damage the mirror surface. The protective fi lm
must remain on the mirror during installation. The fi lm may only be removed
after the attachment to the handlebar is done.
Metal objects such as jacket zips, helmet buckles, watch straps, rings,
rivets, keys, vehicle parts etc. can damage the mirror surface. Do not put
your helmet on the mirrors, the metal helmet buckle may scratch the mirror
surface.
Cleaning the mirror with water, soap and a soft cloth only. Do not use
abrasive cleaning agents or hard objects.
Vibrations
The handlebars are stimulated to vibrate by motor vibrations. Changing the handlebar configuration, i.e. changing the weight, particularly at the end of the handlebars, can lead to an increase in vibrations in the grip area. Permanent, strong vibrations in the grip area can lead to numbness in the hands, reduced visibility in the rear-view mirror or even breakage of the mirror arm. If strong vibrations occur in the grip area after removing handlebar end caps, grips, shortening the handlebars, etc., handlebar weights are required to reduce these vibrations.
Installation
CLASSIC CLUB SPORT RACE &150/180mm Arm
Part of delivery are 3 screws: M10x1.5 / M10x1.25 (one groove at head) and
M10x1.25 left-hand thread (two grooves at head).
Grease the thread of the M10 screw well before mounting.
After aligning the mirror, the M10 screw is tightened with a torque of 20Nm
and the M6 screw in the mirror arm with a torque of 8Nm.
After aligning the mirror, the M5 clamping screw inside the arm is tightened
with a torque of 4Nm.
The mirror arms are made of anodized aluminum. The high-quality surface is
ceramic like and very hard, but can still be worn away by permanent friction
contact with gloves.
Select a mirror location so that your gloves cannot come into contact with the
mirror arms.
After aligning the mirror, the M5 clamping screw inside the arm is tightened
with a torque of 4Nm.
The mirror arms are made of anodized aluminum. The high-quality surface is
ceramic like and very hard, but can still be worn away by permanent friction
contact with gloves.
Select a mirror location so that your gloves cannot come into contact with the
mirror arms.
After aligning the mirror, the M5 clamping screw in the arm is
tightened with a torque of 3Nm.
The orientation of the mirror must be above the handlebars and the vertical
distance between ball head and clamp must be 40mm.
After aligning the mirror, the M6 clamping screw in the arm is tightened with
a torque of 3Nm.
We hope you enjoy your new rear view mirrors and look forward to your positive
review.
Should you ever be unsatisfied, please give us the chance to correct it and
contact us directly at s
ervice@motogadget.de
Documents / Resources
|
motogadget 7001010 Glassless Rear
Mirror
[pdf] Instruction Manual
7001010 Glassless Rear Mirror, 7001010, Glassless Rear Mirror, Rear Mirror,
Mirror
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>