SEALEY VSE4779 Rear Axle Bush Tool Ford Fiesta Instruction Manual
- June 16, 2024
- SEALEY
Table of Contents
SEALEY VSE4779 Rear Axle Bush Tool Ford Fiesta
Product Information
Specifications
- Model: VSE4779.V2
- Application: Ford Fiesta IV, Ka-1996 onwards
- Maximum Load for Screw Rod: 150Nm
Introduction & Application
The Rear Axle Bush Tool (Model No: VSE4779.V2) is designed for use with Ford Fiesta IV and Ka models from 1996 onwards. This tool is used for inserting new bushes into the bush housing of the rear axle. Please refer to Fig.1 and Fig.2 for visual references.
Operation
- Ensure that the vehicle is adequately supported before working underneath.
- Thoroughly lubricate the screw rod threads each time the tool is used
- Remove the rear wheels to gain access to the bush housings at the top of each trailing arm.
- Assemble the tool and bush onto the bush housing as shown in Fig.3.
- Ensure that the screw rod (1) is well lubricated prior to assembly.
- Hold the retention nut (2) with a 24mm ring spanner.
- Using a ratchet wrench with a 24mm deep socket, turn the nut on the force nut assembly (6) clockwise to drive the bush into the housing.
Important Safety Instructions
- Always adhere to Health and Safety, local authority, and general workshop practice regulations when using tools.
- Do not use tools if damaged. Maintain tools in good and clean condition for best and safest performance.
- Ensure that the vehicle is adequately supported with axle stands when jacked up.
- Wear approved eye protection and suitable clothing to avoid snagging. Do not wear jewelry or have long hair untied.
- Do not use the tool for purposes other than for which it is designed.
- Do not use the tool when tired or under the influence of alcohol, drugs, or intoxicating medication.
- Do not use an impact wrench with this tool.
- Store the tool in a safe, dry, childproof area when not in use.
FAQ
- What vehicles is this tool compatible with?
- This tool is compatible with Ford Fiesta IV and Ka models from 1996 onwards.
- Can I use an impact wrench with this tool?
- No, it is not recommended to use an impact wrench with this tool.
- What is the maximum load for the screw rod?
- The maximum load for the screw rod is 150Nm. Exceeding this load will shorten its life and is not covered under warranty.
- Where can I find parts support for this product?
- To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk, or phone 01284 757500.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY INSTRUCTIONS
WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.
- DO NOT use tools if damaged.
- Maintain tools in good and clean condition for best and safest performance.
- Ensure that the vehicle which has been jacked up is adequately supported with axle stands.
- Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer.
- Wear suitable clothing to avoid snagging. Do not wear jewellery and tie back long hair.
- DO NOT use the tool for purposes other than for which it is designed
- DO NOT use the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
- DO NOT use an impact wrench with this tool.
- When not in use, store tool in a safe, dry childproof area.
IMPORTANT! These instructions are provided as a guide only. Always refer to the vehicle manufacturer’s service instructions or a propriety manual, to establish the current procedure and data.
WARNING: The warnings, cautions and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.
INTRODUCTION & APPLICATION
Introduction: Remove/Install rear axle mounting bushes in Ford Fiesta IV,
Ka. Can be used in situ – no need to remove the rear trailing link assembly
from vehicle.
Applications: Ford Fiesta IV, Ka-1996 onwards.
DESCRIPTION
- SCREW ROD
- RETENTION NUT
- PUSHING CUP
- RECEIVING CUP
- INSERTION CUP
- FORCE NUT
Operation
DO NOT USE AN IMPACT WRENCH WITH THIS TOOL.
- Before working under the vehicle ensure that it is adequately supported.
- Thoroughly lubricate the screw rod threads each time the tool is used.
- Remove the rear wheels to gain access to the bush housings at the top of each trailing arm. For a detailed and up to date breakdown of this procedure refer to the vehicle manufacturer’s service instructions, or a proprietary manual.
- Thoroughly apply penetrating oil to each bush to aid extraction from the bush housing.
- To extract the old bush, assemble the tool onto the bush as shown in Fig.2. Ensure that the screw rod (1) is well lubricated prior to assembly. Hold the retention nut (2) with a 24mm ring spanner. Using a ratchet wrench with a 24mm deep socket turn the nut on the force nut assembly (6) clockwise to drive the bush out of its housing.
- To insert the new bush, assemble the tool and bush onto the bush housing as shown in Fig.3. Ensure that the screw rod (1) is well lubricated prior to assembly. Hold the retention nut (2) with a 24mm ring spanner. Using a ratchet wrench with a 24mm deep socket turn the nut on the force nut assembly (6) clockwise to drive the bush into the housing.
Screw rod maximum load 150Nm. Exceeding this load will shorten the life of the screw rod. The screw rod is considered to be a consumable item and is NOT covered under warranty.
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to
- www.sealey.co.uk,
- email sales@sealey.co.uk or
- phone 01284 757500.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: The guarantee is 12 months from the purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor, Sealey Group, Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk, IP32 7AR
- 01284 757500
- 01284 703534
- www.sealey.co.uk
- sales@sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>