BeBa 24911 Wall Hung Smart Bidet Toilet Purificare User Manual

: June 16, 2024
: Beba

24911 Wall Hung Smart Bidet Toilet Purificare

Product Information

Specifications

Product Name: Wall Mounted Intelligent Toilet
Model Numbers: BeBa_24911, BeBa_26880
Remote Control: Included (Batteries Not Included)
IPX4 Ingress Protection
Rear and Front Wash Functions

Parts List

Toilet
Remote Control (Batteries Not Included)
Remote Control Holder
Electrical Cable Coupler
Flow Limiter
Stop Valve
Filter x 2
Flush Pipe and Seal
Waste Pipe and Seal
Wall Fixing Rods
Wall Fixing Nuts
Wall Fixing Washers
Side Fixing Bolt Sleeve
Wall Cushion

Tools Required

Tape Measure
Pencil
Phillips Screwdriver
Flat Head Screwdriver
Knife
File
Adjustable Wrench
Wire Strippers
12mm Drill bit
Hacksaw
Drill

Product Overview

The Wall Mounted Intelligent Toilet is a high-tech toilet that
offers rear and front wash functions. It comes with a remote
control for easy operation. The toilet is designed to be mounted on
the wall, saving space in your bathroom.

Installation Instructions

Before starting the installation, make sure to read and
understand all safety information in the user manual.

1. Safety Information

Refer to page 3 of the user manual for important safety
information regarding the installation and use of the toilet.

2. Unit Measurements

Refer to page 5 of the user manual for the measurements of the
toilet unit.

3. Parts List

Refer to page 7 of the user manual for a list of all the parts
included with the toilet.

4. Before Installation

Refer to page 9 of the user manual for recommended installation
area and instructions on preparing the flush pipe and waste pipe
from the wall frame.

5. Installation

Refer to page 10 of the user manual for detailed installation
instructions.

5.1 Connect the Stop Valve

Connect the stop valve to the pipe end, ensuring to fit an
adequate seal and tighten using a spanner.
Once connected and fully tightened, place a bucket under the
stop valve, open the stop valve and flush the pipe for at least 10
seconds to remove any debris in the system.
Once flushed through, turn the stop valve to the closed
position.

5.2 Connect the Filter

Connect the 1/2 female threaded end of the Filter to the Stop
Valve, ensuring to fit the seal provided and tighten.
Connect the 3/8 – 1/2 Flexi Pipe to the Filter, ensuring to fit
the seal provided and tighten using a spanner. Do not over tighten
as this could crack the plastic body of the Filter.

5.3 Flush Pipe and Waste Pipe Installation

Push the flush pipe and waste pipe supplied into the wall
frame, ensuring these are level and aligned. Using a ruler draw a
line on the flush and waste pipe, where it meets the wall
surface.
Remove the pipes from the wall and push them fully onto and
into the back of the toilet pan, using a ruler mark a line level
with the back of the pan. Remove the flush pipe and measure the
distance between the two marks, this will be dimension L1.
From the end of the flush pipe measure dimension L1 and then
add 6mm, cut at this point. Carry out the same process for the
waste pipe, but only add 3mm and cut at this point.
Once cut, use a file to smooth off the pipes internally and
create a chamfer on the external edge.
After cutting and filing, insert the pipes into the back of the
toilet and ensure these are fully attached.

6. Remote Control

Refer to page 17 of the user manual for instructions on using
the remote control.

7. Operation

Refer to page 18 of the user manual for instructions on
operating the intelligent toilet.

8. Cleaning and Maintenance

Refer to page 24 of the user manual for instructions on cleaning
and maintaining the toilet.

9. Replacing the Filter

Refer to page 25 of the user manual for instructions on
replacing the filter.

10. Draining the Water Tank

Refer to page 26 of the user manual for instructions on draining
the water tank.

11. Troubleshooting

Refer to page 27 of the user manual for troubleshooting tips and
solutions.

12. Support

Refer to page 28 of the user manual for contact information for
technical support.

Technical Specifications

Refer to page 29 of the user manual for detailed technical
specifications of the toilet.

FAQ

1.  **Q: What is the required water supply pressure for the

toilet?**

A: The required water supply pressure is 0.7-7.5 Bar as stated
in the instruction manual. Check the water supply when connecting
the filter. To meet 0.7 bar water supply there should be 1.5L water
(3 bottles water @ 500ml) within 60 seconds. Please note this is
after the filter is installed. If this is not met, water flow must
be increased.

```
1.  **Q: What tools are required for  
```
installation?**

A: The tools required for installation include a tape measure,
pencil, Phillips screwdriver, flat head screwdriver, knife, file,
adjustable wrench, wire strippers, 12mm drill bit, hacksaw, and
drill.

1.  **Q: How do I clean and maintain the

toilet?**

A: Refer to page 24 of the user manual for instructions on
cleaning and maintaining the toilet.

WALL MOUNTED INTELLIGENT TOILET
BeBa_24911 BeBa_26880 REMOTE CONTROL IPX4 INGRESS PROTECTION REAR AND FRONT WASH

CONTENTS

SAFETY INFORMATION

3

UNIT MEASUREMENTS

5

PARTS LIST

7

PRODUCT OVERVIEW

8

BEFORE INSTALLATION

9

INSTALLATION

10

REMOTE CONTROL

17

OPERATION

18

CLEANING AND MAINTENANCE

24

REPLACING THE FILTER

25

DRAINING THE WATER TANK

26

TROUBLESHOOTING

27

SUPPORT

28

TECHNICAL SPECIFICATIONS

29

2

SAFETY INFORMATION
This manual must be read and fully understood before installing or using the appliance. This product must not be operated without a connected water supply. Installation must be in accordance with all relevant local regulations applicable at the time of installation. It must be installed by a qualified professional to in accordance with BS 7671. If electrical work is carried out within the bathroom which involves addition or alteration of existing circuits, it may be notifiable to your local building control department (Part P). If unsure, professional advice should be sought. The toilet must be fitted in accordance with the Water Supply (Water Fittings) Regulations and Water Supply (Water Fittings) (Scotland) Byelaws. If the power cable or RCD are damaged in any way, the power must be disconnected until the part is replaced. Contact the retailer or manufacturer. The toilet must be fitted in a well- ventilated bathroom. The toilet must not be sprayed with liquid, or placed in a position it is likely to be sprayed. The toilet must not be installed in a location where it may be subject to high temperatures. The toilet must be stored in an upright position before installation. Do not over bend or kink the water supply hose as this could cause leaks Only use this product for its intended use. Only use attachments recommended by the manufacturer. Do not use this product in an outdoor environment. Children and people with limited physical, sensory or capabilities must be supervised when using this device or have been told the proper procedure for use beforehand. Do not climb or stand on the toilet. If the product is not working properly, disconnect from the mains and close the water supply valve immediately before contacting the supplier or a qualified professional. This is a Class I electrical appliance and must be correctly earthed. Make sure the earth cable is connected first during the electrical connection. In case of any damage to the supply cable, you must arrange for a certified and qualified electrician to replace the cable for you. This appliance is designed for fixed connection to the power supply. Connecting this appliance to the power supply must be performed by a qualified and authorised electrician. Incorrect repairs are dangerous. Repairs must only be carried out by trained and qualified engineers.
3

INSTALLATION DIAGRAMS – BeBa_24911
5

INSTALLATION DIAGRAMS – BeBa_26880
6

PARTS LIST

Toilet

Remote (Ba eries Not Included)

Remote Control Holder

Electrical Cable Coupler

G3/8″ ½” Flexi Hose

Flow Limiter

Stop Valve

Filter x 2

Flush Pipe and Seal

Waste Pipe and Seal

Wall Fixing Rods

Wall Fixing Nuts

Wall Fixing Washers

Side Fixing Bolt Sleeve 7

Wall Cushion

TOOLS REQUIRED

Tape Measure

Pencil

Phillips Screwdriver Flat Head Screwdriver

Knife

File

Adjustable Wrench

Wire Strippers

12mm Drill bit

Hacksaw

Drill

PRODUCT OVERVIEW

8

BEFORE INSTALLATION
Recommended installation area.
IMPORTANT! Before commencing installation, the water and electrical supplies should be turned OFF. Please note with your floor mounted back to wall toilet, a Flush Pipe and Waste Pipe are supplied, these may not be required as it will be dependant on the cistern to which the toilet is being connected and the position of the soil stack. Before attempting installation, ensure that you are in possession of all the required tools and fittings to ensure successful installation. Prepare the wall with the wall frame fitted, tiled/finished with access holes prepared for the flush pipe and waste pipe. Prepare the water supply pipe with a 1/2″ female connector and electrical 3 core cable (which should be connected to a 13-amp fuse spur or isolation switch outside the bathroom) as per below, allowing for 200mm of water supply pipe and 400mm of electrical cable to extend beyond the surface against which the toilet will sit, to allow connection to the toilet unit.
Flush pipe from Wall Frame Waste pipe from Wall Frame
9

INSTALLATION INSTRUCTIONS
Connect the stop valve to the pipe end, ensuring to fit an adequate seal and tighten using a spanner.
Once connected and fully tightened, place a bucket under the stop valve, open the stop valve and flush the pipe for at least 10 seconds to remove any debris in the system.
Once flushed through, turn the stop valve to the closed position.

to fit the seal provided and tighten.

Connect the 1/2″ female threaded end of the Filter to the Stop Valve, ensuring

Connect the 3/8″” – 1/2″ Flexi Pipe to the Filter, ensuring to fit the seal provided and tighten using a spanner, do not over tighten as this could crack the plastic body of the Filter.

The required water supply pressure is 0.7-7.5 Bar as stated in the instruction manual. Check the water supply when connecting the filter. To meet 0.7 bar water supply there should be 1.5L water (3 bottles water @ 500ml) within 60 seconds. Please note this is after the filter is installed. If this is not met, water flow must be increased.
Push the flush pipe and waste pipe supplied into the wall frame, ensuring these are level and aligned. Using a ruler draw a line on the flush and waste pipe, where it meets the wall surface.

10

Remove the pipes from the wall and push them fully onto and into the back of the toilet pan, using a ruler mark a line level with the back of the pan. Remove the flush pipe and measure and measure the distance between the two marks, this will be dimension L1.
From the end of the flush pipe measure dimension L1 and then add 6mm, cut at this point, as shown below. Carry out the same process for the waste pipe, but only add 3mm and cut at this point as shown below.
Once cut, using a file, smooth off the pies internally and create a chamfer on the external edge as shown below.
After cutting and filing, insert the pipes into the back of the toilet and ensure these are fully attached.
11

Remove the screws on the seat, using a cross head screwdriver, ensuring not to lose the screws once removed. Two people may be required for the next part of the installation.
Pull the seat from the toilet pan (do not turn this upside down).
The threaded bolts should be attached to the frame and screwed inwards until 48mm of thread is left exposed, as shown below.
Place the toilet cushion against the wall over the threaded bolts and pipe holes
12

Push the toilet base into position against the wall, ensuring that the waste and flush pipes to the rear engage to create a full seal and the holes in the back of the pan sit over the threaded bolts on the frame.
Pull through the flexi pipe and cable, to allow connection to be made with the seat unit.
Push the threaded bolt sleeves over the threaded bolts and into the hole in the pan to prevent the metal of the bolt damaged the ceramic, during use. Place the washer onto the threaded bolt, then fit the nut and tighten until the pan is secure.
13

Slide out the support box from underneath the toilet pan, only when the pan is secured.
Trim the cushion which is exposed around the edge of the toilet pan, using a sharp knife.
Strip the end of the household cable to expose the wires for connection to the coupler. When stripped, tidy the ends and connect to the coupler as shown, ensuring the screws are tightened and the wire ends are fully secured.
Carry out the same process for the cable attached to the toilet, then connect the coupler sections together.
14

Connect the end of the water supply flexi to the tank inlet on the underside of the toilet lid, this will require a firm push to connect the flexi to the inlet. Once fully inserted and secure, tighten the nut. Before replacing the seat, turn on the water supply, the stop valve and the electrical supply.
After turning on the water and electrical supplies you MUST carry out the RCD test, instructions for this are printed on the rear of the RCD, also carry out a leak check on all water connections.
If the water volume within the flushing system is too great and water splashes over the rim, a flush rate limiter is necessary. If after installing the limiter, the bowl does not fully empty/clean, cut off one or more teeth of the limiter
When checks are completed and no leaks are found and RCD test is passed, the lid assembly can be re-fitted to the pan, feed the flexi pipe and cables carefully under the pan, so as not to trap the pipe or cable or cause any kinks, which will reduce water flow.
Locate the seat onto the pan and push down at the rear (not in the middle), as this could crack the seat.
When the seat is located, re-fit the seat screws and tighten until secure, then fit the cover caps.
15

INSTALLATION OF THE REMOTE HOLDER
Clean the wall surface in the area in which the remotecontrol holder will be located Dry fully before attempting the installation
From the rear of the holder, peel off the adhesive strip cover.
Place the holder with the adhesive side to the wall, ensuring this is level, press to the wall firmly and hold for a couple of seconds.
Once located and secure, place the remote control against the holder. The magnet within the holder will retain the remote in position.
16

On receipt of your remote, this should be synced to your toilet, if the remote does not work initially, check the batteries are installed and installed correctly and then try to sync the remote using the “Remote Sync” section The same applies when batteries are changed.

OPERATION
REAR WASH/ FRONT WASH
While seated, press the rear wash or front wash button on the remote and the toilet will begin wash mode.
Alternatively, the dial on the side of the toilet can be turned clockwise to activate front wash or anticlockwise to activate rear wash. The washing function will run for 3 minutes.
Once your product is installed and all water and electrical supplies are csNouOnpTnpEeliec:steaad.rOeanncdcoenonpyeoecuratretpidornaoandldu, cyotopiuserriantotsiitolaenltlaeisld, ryaeonauddryatolfloilwer tauitsseerr.eaanddyefolercutrsicea. l NOTE: The toilet seat must have a water supply connected, the toilet Lift up the toilet seat lid, locate yourself so that the sensor detects a cuisseter.rn filling and the toilet flushing does not automatically confirm a water sPurepspslythisecwoansnhecbtuetdtotno,twhehesneayto. u do this the toilet will carry out initially NanOaTuEt:oImf tahteic tnooilzezt lies sneoltf- ucsleeadnfowrh7ic2hhloaustrs ftohreanreoxutnodp9ersaetcioonndwsillabned pthreoncetehdeewdabsyh a(fotarnukseclre)awni,llpcloemasmeernecfeer. to “Tank Self Clean Section” OWpheernatyioonu stop the wash, the toilet will self-clean for around 9 seconds. LWifht eunp tthhee wtoailseht smeoadt elidis, laocctaivteatyeodu, rasfetelfrsao1th0astetchoensdednesolarydtehteecntoszazlueser. will move for 18 seconds before staying in the set position for the rest of Pthreeswsatshhe. wash button, when you do this the toilet will carry out an aWuhtoilme aintiwc ansohzzmleosdeel,f-ycoleuacnawnhaidchjuslatstthsefoforllaorwouinngds9etstiencgosn: ds. The nozzle chamber flap will open, the nozzle will not immediately extend, but water will run from the chamber starting the cleaning process. The nozzle will then extend and water will continue to run (not spray), after approx. 9 seconds the wash (for user) will commence and start the spray. When you stop the wash, the toilet will self-clean for around 9 seconds. When the wash mode is activated, after a 10 second delay the nozzle will move for 18 seconds before staying in the set position for the rest of the wash. While in wash mode, you can adjust the following settings:
18

MASSAGE
Change between “OSCILLATING”, “PULSATING” AND “OSCILLATING AND PULSATING” functions.

To access massage mode, keep pressing the + or temperature buttons. Then, press the + water flow button to change between the different massage functions.
The Indicator lights on the remote will show the massage mode selected. 1 Light Oscillating Mode 2 Lights Pulsating Mode 3 Lights Oscillating and Pulsating Mode Please Note: The massage mode can only be adjusted using the remote control.

WATER FLOW
Change between LOW, MEDIUM or HIGH

To adjust the water flow, press the + or water flow buttons on the remote. The indicator will show the rate that the water is flowing between LOW, MEDIUM and HIGH.

You can also adjust the water flow using the dial located on the side of the toilet. Turn the dial clockwise to increase the flow or anticlockwise to decrease.

19

WATER TEMPERATURE ADJUSTMENT

The water temperature can be adjusted.

Use the temperature adjustment

KPreesespanpdrheosldstihnegdiatlhoen tdheiaslidoe nof tohileet.sTihdee

buttons on the remote. Press the + oTefmthpeerattuorielecat.n Tthhenebeteinmcrpeaeserad tbuyrtuerncinagn

or to increase or decrease the

tchloecknwibseeoirndcecrreeaasseed dbybtuyrnitnugrint ainntgiclockwise.

temperature.

cMloovcek”AwirisDery MoorddeeancdreInadiscaetodr Lbigyhtt”utorn”Ointhger iftunacntiotnics”loseccktiwoni,saes .these are not functions that
you would change during the wash function.

STOP
Stops all functions immediately no matter where they are in their cycle.
To stop any of the functions at any time, press the stop button on the remote control.
ADJUST NOZZLE
The nozzle position controls where the water is sprayed during washing mode.
Change the nozzle position by using the + and nozzle buttons on the remote to retract or extend the nozzle. Please Note: The nozzle position can only be adjusted using the remote control.

20

Note: If the dial light flashes slowly (once every 2-3 seconds) during normal use, this doesn’t indicate a fault. Please open the cover, do not sit on the seat, pull the knob and rotate it in the clockwise direction. The ambient light will be turned off. It will be turned back on when rotating it in the clockwise direction again.ction again.

REMROemTEotCeOCNoTnRtrOoLl SSyYnNcCH
Step 1 Open the lid and the seat. Turn o the night light using the side control (Refer to the “light Se ng”)

Step 2

Press and hold the STOP bu on (1) and “-”

bu on (4) at the same me for a few

seconds un

rst light (5) ashes.

Step 3 Release the STOP bu on (1) but keep pressing “-“bu on (4).

Step 4 While s ll Pressing “-” bu on (4), press “-” bu on (2) then “+”bu on (3) then release the “-” bu on (4), the indicator lights will
ash on and you will then know the ID code for the toilet by referring to the table below for future reference and the remote is then synced with the toilet.

A few second later, all lights will turn o and you can start to control the toilet.

For mu nstalla ons:

When you nish the above 4 steps, you can

press “-” bu on (2) and “+”bu on (3) to

change the ID code for the toilet.

There are 5 lights, but only

t 4 lights

indicate for the ID code as below:

Not Illuminated

Illuminated

LIGHT SHOWING

ID CODE NO

0

1

2

3

4

5

6

7

8

9

23

CLEANING AND MAINTENANCE

Daily

Remove water drops with a soft lint free

cloth to avoid limescale build-up.

Weekly

Clean all surfaces and corners. Clean

the spray nozzle is necessary (see

Nozzle cleaning)

Monthly

Clean the ceramic with low acidic

cleaning agents.

Every 6 months

Replace the filter if required. (see

replacing the filter)

NOTE: Do not use strong abrasive cleaning agents or materials, as this can damage

the product and will invalidate your guarantee.

TANK SELF-CLEAN

If the product is not used for more than 72 hours, the next time it is used, and the wash function is activated, the unit will carry out a self-clean for approximately 3 minutes. All functions will be de-activated during this time.
The nozzle will not extend but water will run out form inside the chamber into the toilet until the clean is completes

CLEANING THE NOZZLE

It is recommended that regular cleaning of the nozzle takes place to prevent blockages.
To manually clean the nozzle, follow the below:

Open the seat cover and seat, then rotate the control dial clockwise. The nozzle will extend, rub clean with a brush to clean the nozzle holes and then wipe clean.

The nozzle will return after a 5-minute period or you can press the Stop button.

24

REPLACING THE FILTER The filter supplied has a life of 6 months and should be replaced to prevent reduced flow. This can be affected by the water type i.e. Hard Water areas.
To replace the filter, you will need to turn off the power supply and the water supply and the seat will need to be removed. Once the power has been cut to the unit, unscrew the seat from the toilet, do not turn the seat upside down. Once removed, access the filter and the stop valve.
Turn the stop valve to the closed position.
Disconnect the filter and replace with the new part, ensuring to re-fit the seals.
Feed the pipes back into the toilet base, turn the power back on and re-set the RCD Re-open the stop valve. Re-fit the seat and secure into position.
25

DRAINING THE WATER TANK The water and power must be cut to the unit before work is started Do not invert the seat. Ensure a water holding container is in place prior to draining
Using pliers hold the plug on the tank turn the plug to OPEN and pull out Water will start to drain. After draining is completed, insert the plug and turn to CLOSE.
26

TROUBLESHOOTING

Problem

Potential cause The power supply may not be connected
The water supply may be disconnected

The filter may be blocked

The washing function Seat detector not activated

not operating

Toilet lid is closed

Function not used for more than 72 hours

Seat assembly is not connected to water supply

Seat not working and

double beeping

Hall sensor or infrared

when lid up, seat down sensor failure

and sensor covered

The washing cycle is 3mins. The

nozzle will stop spraying after

Washing function

3mins, and then retract.

suddenly stops and Water supply interrupted

nozzle retracts.

The seat detector has sensed

the user left the seat

The toilet lid is not fully open

The water flow rate may be set

at low grades

The water supply pressure may

Low water flow rate be too low

The filter may be blocked

Low water temperature

The nozzle may be blocked The water temperature may be set at low grades The temperature of water supply is too low

The nozzle comes out slowly The water flows out but the nozzle does not come out The dryer cannot work
Low air temperature
Night light is always off
Night light is always on.

Upon starting the washing function, the nozzle will be in self-cleaning mode before coming out. The toilet is not used for more than 72 hours
The power supply may not be opened Not correctly seated The cover is closed The air temperature may be set at low grades
The air heater is not working normally To much light in the surrounding environment.
The night light function may be closed.
1. Environment is dark.

Suggested action Ensure the power switch is in the on position and the RCD has been reset. Ensure the inlet water valve is in the open position, and ensure there is adequate water flow to the unit. Please replace a new filter. It has a service life of approx. 6 months. Ensure the seat is occupied to activate the function. Lift the toilet seat. The self-cleaning function will activate, which takes around 3 minutes. During self-cleaning all the buttons are deactivated until the function has completed. Check the seat assembly has a connected and flowing water supply, as the cistern filling does not confirm water to the seat.
Replace seat assembly
This is normal and please press the “wash” button to start another wash cycle.
Please check if there is a water outage
Please adjust sitting position
Ensure the lid remains upright during the function. Please increase the flow rate as per “adjusting water flow rate” of operating instructions Please check and ensure the water supply pressure is 0.07Mpa Replace the filter. It has a service life of approx. half a year Please replace the nozzle Please set the water temperature at high grade as per “adjusting temperature “of the operating instructions Please set the water temperature at high grade as per “adjusting temperature “of operating instructions, or decrease the flow rate as per “adjusting water flow rate”.
This is normal
This is normal. If not used for more than 72 hours, when the unit starts it will begin the self-cleaning for about 3 minutes
Please turn on the power
Please sit on the seat and adjust sitting position Please open the cover and sit on the seat Please set the air temperature at high grade as per “adjusting temperature “of operating instructions
Please contact local distributor
When the night light is set at smart mode, the night light will not work when in the bright environment. Please open the night light function and adjust the night light mode as per “Light Setting”. When the night light is set to smart mode, the night light will be always on when in a dark environment

27

TECHNICAL SPECIFICATIONS

MODEL

Rear Wash

Front Wash

Oscillating Spray

Wash

Pulsating Spray Oscillating and Pulsating Spray

Adjustable Water Temperature

Adjustable Flow Rate

Adjustable Spray Position

Warm Air

Air Drying Adjustable Dryer Temperature

Hygiene

Nozzle Self Cleaning Nozzle Manually Cleaning

Night Light

Breathing Lamp

Soft Closing Seat and Cover

Body Control dial

Remote Control

Rimless Toilet

Installation of the toilet

Water Supply Connector

Rated Voltage

Power

Length of Power Cord

Water Supply Pressure

Water Supply Temperature

Ambient Temperature

Protection Degree

Flow Rate

wash Device

Water Temperature Wash Cycle Time Heating Mode

Maximum Heater Power

Safety Device

Dry Device

Backflow Prevention Maximum Speed Of Air Maximum Dryer Power Dry Cycle Time Warm Air Temperature

Safety Device

Remote Control

Frequency Range Maximum RF Output Power Type of batteries

Number of batteries

Net Weight

Dimensions

28

BeBa_24911/Beba_26880
5 Steps (Default 3rd) 5 Steps (Default 3rd) 5 Steps (Default 3rd)
5 Steps (Default 3rd)
Wall Mounted
G 3/8″ ½” AC220240V, 50/60HZ
950W 1.8m 0.07~0.75MPa (0.7~7.5Bar) 4~35 C 4~40 C IPX4 350~650mL/min 31~39 C 3 Minutes Tank 1200W Thermal Cutoff/ FusesLiquid Level SwitchThermostat Air Gap 5m/S 280W 3 Minutes 35~50 C Thermal Cutoff/ fuse>Thermostat 2460MHz 10dBm 3V CR2032 Two pieces 32 Kg 593 x 370 x 380mm

The nozzle goes back automatically when manual cleaning
The remote control is not functioning
There are BEEP sounds when the bidet is operating
The bidet does not function normally The light around the control dial flashes twice with constant BEEP TThheelilgighht taraoruonudntdhethdeial ckoeenptrsoflladsihailnkge(eonpcse every fslaecsohnindgor less).

2. Something may be covering the control dial.
3. The night light may be set to `Always On’ mode
1. The nozzle goes back after washing 5 minutes
2. Press the “stop” button
3. The seat detector senses that the seat is closing
1. There are no batteries in the remote control
2. Maybe the battery power is too low
3. Maybe the code of the bidet and remote control is not
the same There is a short BEEP when you are sitting down, and a long BEEP when you leave. Also, there is a short BEEP when the bidet has received commands.
Abnormal operation
The water supply temperature may be too high
There may be something wrong with the product

Remove the obstructions around the control dial Please adjust the night light mode as per “Light Setting” of operating instructions This is normal Manual cleaning will be stopped if you press the control dial or press the “stop” button on the remote control. Please do not put down seat during manual cleaning
Please install the correct batteries in the remote control
When batteries are low, LED will flash. Change the batteries
Please set the code of the remote control to the correct one. See “Remote Control Synch”
This is normal. You can turn off the sound. See “Sound Setting”
Please shut off the power and turn on after one minute. If the bidet still cannot work, please contact local distributor
Please shut off the power and water supply, stop using the product, and then contact local distributor
Please shut off the power and water supply, stop using the product, and then contact local distributor.

If you should encounter an issue with operation/function of your product please contact BID Customer Service. To assist in the resolution, we will require your Serial number, a video of the issue, including operation of the remote or dial, position of the seat, video of the side control and sound to indicate any beeps which occur, this will give a full picture of the operation to help determine the best resolution or guidance.

SUPPORT
Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centers.
At the time of printing the product contains no substances listed within Annex XIV of the Reach Regulations (EC) 1907/2006. In accordance with Article 59 of the same regulation the following substances are contained within the product at permitted levels: Lead & Cadmium. As a responsible manufacturer the regulations are monitored to ensure continued compliance. Further information can be provided upon request.

28
call 0330 390 3062 Write to Trident Business Park, Leeds Road, HD2 1UA

EU DECLARATION OF CONFORMITY

Company Name: Postal Address:
Postcode Telephone Number E-mail Address

Buy It Direct

Trident Business Park

The Black Church

Leeds Road

St Mary’s Place

HD2 1UA

Dublin 7

0871 620 1057

01 255 2070

Compliance@BuyitDirect.co.uk

This declaration of conformity is issued under our sole responsibility and belongs to the following product:

Type of product:

Wall Mounted Intelligent toilet

Model Number:

BeBa_24911 / BeBa_26880

Brand:

Better Bathrooms

Object of Declaration

BeBa_24911 and BeBa_26880 Wall Mounted

Intelligent Toilets

The object of the declaration described above is in conformity with the relevant

Union harmonisation legislation:

Low Voltage Directive 2014/35/EU EMC Directive 2014/30/EU RoHS Directive 2011/65/EU Radio Equipment Directive 2014/53/EU

Relevant harmonised standards used or other technical specifications in relation to

which conformity is declared:

SAFETY EN 60335-1:2012 +A13:2017

EN 62233:2008

EN 60335-2-84:2003 + A1:2008

EMC

EN 61000-3-2:2014

EN 55014-1:2017

EN 61000-3-3:2013

EN 55014-2:2015

RED

EN 301489 -1 V2.1.1:2017

EN 300440 V2.1.1:2017

EN 301489 -3 V2.1.1:2017

RoHS

EU 2015/863

Authorised Signature

Richard Leach Compliance and Quality Manager 24th August 2023
30

UK DECLARATION OF CONFORMITY

Company Name: Postal Address:
Postcode Telephone Number E-mail Address

Buy It Direct Trident Business Park Leeds Road HD2 1UA 0871 620 1057 Compliance@BuyitDirect.co.uk

This declaration of conformity is issued under our sole responsibility and belongs to

the following product:

Type of product:

Wall Mounted Intelligent toilet

Model Number:

BeBa_24911 / BeBa_26880

Brand:

Better Bathrooms

Object of Declaration

BeBa_24911 and BeBa_26880 Wall Mounted

Intelligent Toilets

The object of the declaration described above is in conformity with the relevant UK Statutory Instruments and Regulations:
Electrical Equipment (Safety) Regulations 2016 Electromagnetic Compatibility Regulations 2016 The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 The Radio Equipment Regulations 2017

Relevant designated standards used or other technical specifications in relation to

which conformity is declared:

SAFETY EN 60335-1:2012 +A13:2017

EN 62233:2008

EN 60335-2-84:2003 + A1:2008

EMC

EN 61000-3-2:2014

EN 55014-1:2017

EN 61000-3-3:2013

EN 55014-2:2015

RED

EN 301489 -1 V2.1.1:2017

EN 300440 V2.1.1:2017

EN 301489 -3 V2.1.1:2017

RoHS

EU 2015/863

Authorised Signature

Richard Leach Compliance and Quality Manager 24th August 2023
31

DECLARATION OF PERFORMANCE DOP BB-34-24911/26880

UKCA Company Name: Postal Address: Postcode
CE Company Name: Postal Address: Postcode
E-mail Address

Buy It Direct Trident Business Park, Leeds Road, HD2 1UA
Buy It Direct The Black Church, St Mary’s Place, Dublin 7
Compliance@BuyItDirect.co.uk

This declaration of performance is issued under our sole responsibility and belongs to the following product:

Type of product: Model Number: Brand: Object of Declaration

Wall Mounted Intelligent toilet BeBa_24911/ BeBa_26880 Better Bathrooms BeBa_24911 and BeBa_26880 Wall Mounted Intelligent Toilet

We hereby declare that the products named above have been designed, are produced and have been tested to comply with:
Union Harmonisaon Legislaon and relevant harmonised standards Regulation (EU) No, 305/2011
Designated standards and relevant UK Statutory Instruments and Regulation Construction Products (Amendment etc.) (EU Exit) Regulations 2020 SI 2020/1359
BS EN997:2012+A1:2015

Personal Hygiene AVCP System 4

Essential Characteristics CL 1 -6A Class 1 product/ Flushing cistern WL Water Tightness / Leak Tightness BP Back Flow Prevention CA – Cleanability LR Load Resistance DA Durability

PASS PASS PASS PASS PASS PASS

Authorised Signature

Craig Watson Technical Manager 9/9/22
32

33

236E400-E71-01H