BUN BeBa 26905 Close Coupled Toilet with Soft Close Seat Instruction Manual

BUN BeBa 26905 Close Coupled Toilet with Soft Close Seat

Contents

1. 2XFloor brackets
2. 2X wallplugs S10X50
3. 2X Hex head screw 6 X60
4. 2X Washers
5. 2X St. Steel Screw 5X60
6. 2X Nylon Bushes
7. 2X Chrome Caps

Installation Layout

Tip

1. Read all manipulation and installation guideline, and please install it step by step according to the installation guideline and prevent any damage from product breakage and improper use.
2. All material are written according to the latest information when design. Our company reserves the right to change product characteristics, package and supply at any time without notice.
3. Do not use corrosive detergent (such as hypochlorite) in water tank because such strong oxidant makes fittings damaged easily and lead to leakage. The mentioned above situations are beyond the range of our guarantee.
4. Our company do not bear the related loses and damages caused by use other company’s parts and material such as glass glue.
5. Suitable temperature range: 0~45°C

Functional Instruction

1. The flush valve has 2 flushing ways: half-flush and full flush; when you push the full flush, the discharge volume is big and when you push the half flush, the discharge volume is small.
2. Water level of half flush is adjustable. (Refer to photo 6)
3. Water level of full flush is adjustable. (Refer to photo 3-2)

Installation Steps

1. Preparation before Installation
   Remove the old fittings and wash tank before installation. And wash clean because many impurities probably existed in conduit

2. Flush Valve Installation (According to the actual need)

3. Stainless steel hook for one-piece flush valve installation

  * Contrarotate drainage body and make it remove fro pedestal.
  * Circumrotate stainless steel hook to the end of bolt clockwise.
  * Let pedestal aim at the water tank scupper, deflect properly, circumrotate, and, the stainless steel hook can reach the scupper downside, then, revise the pedestal the sealing washer should put upside. Go through the pedestal by the middle finger of left hand to keep off stainless steel hook and make its both sides put around the outfall symmetrically
  * Circumrotate bolt by screwdriver and be sure that seal between sealing washer and the surrounding for outfall.
  * Let flush valve body insert into pedestal and circumrotate it inside the buckle clockwise.
2. Two-piece flush valve installation
  * Contrarotate drainage body and make it removed from pedestal.
  * Let pedestal insert into outfall from inside of water tank, cover the drainage plastic washer, circumrotate the drainage nut and cover the standard washer, and it can adjust the put angle properly according to the actual size of water tank.
  * Let flush valve body insert into pedestal and circumrotate it inside the buckle clockwise.

3. Fill Valve Installation

   • Put fill valve & water- inlet triangle washer insert into water-inlet hole of water tank, then, cover the water-inlet plastic washer and hexagonal nut in turn from the bottom of fill valve. Fastening water -inlet hexagonal nut and make a proper adjust according to the size of water tank.
   • Adjust water level: Fetch out the buckle and screw off the water-inlet body anti-clockwise: pull upside or press downside to the proper situation, then, screwing on the water-inlet body closely and install the buckle.Little adjustment on water level revolve adjusted rod to adjust the height of water -stop cup and buoy to reach the suitable water level you need
   • Connect the water-supply pipe and built in adapter or filter accordina to vour actual need.
     Notice:
   1. Be sure that buoy is active freely before fill valve installation.
   2. Wash the impurity in the conduit when you connecting the water-supply pipe.
   3. The height of water level can not beyond overflow mouth of flush valve when adjusting water level.

4. Water tank Installation
   Put water tank on ceramic toilet and make standard washer located at the outfall of toilet. Just the photo shows, let jointed bolt insert into installation hole, then, screw the jointed nut closely.

5. Examination
   As photo show, connect the water-inlet pipe to test and notice the following phenomenon:

6. According to the height of half flush to adjust half flush water level: when half flush buoy is higher, the drainage volume is less; when it is lower, the drainage volume is more.

7. Adjust the height of water level by the adjusted digit and its corresponding adjusted patch. The placket is big and its water level is high; the placket is small and its water level is low (Note: When adjusting full flush water level, please fetch out flush valve, then, install flush valve again correctly after adiusted.)

8. Adjust all parts position to prevent them from interference.

9. Open & close for the water-stop cup is normal and has no leakage.

10. It is normal for full flush and half flush

11. Push button Installation

    • Screw off push button nut.
    • Let push button insert into water tank lid middle hole, screwing on push button nut from the bottom of water tank lid, then, screwing the adjusted nut closely and be sure that it is firm.
    • Please confirm pull flush rod press the flush valve key-press whether or not and check it is blocked or not.
    • Note: Screw off pull flush rod, the cut part is upside.
    • Note: Pull flush rod should aim at the full flush key press.

12. Examination Again
    Cover water tank lid and notice the following phenomenon to confirm installation complete or not:

13. Open & close for water-stop washer is normal and has no leakage.

14. It is normal for full flush and half flush and they flush excellently.

Trouble Shooting

Soft Close Toilet Seat

Installation Instructions

1. Insert the hinges into the toilet.
2. Tighten the screws in a clockwise direction(do not over-tighten)
3. Untighten the screws a bit by turning them 90° in an anti-clockwise direction this will allow you to align the seat.
4. Clip on the toilet seat.
5. Align the toilet seat with ceramic bowl.
6. Take off the toilet seat by pressing both push buttons
7. Tighten the screws in a clockwise direction
8. Place the cover over the hinges
9. Clip on the toilet seat and cover.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>