Raex TQL25-58 Charging Electric Shutter System Instruction Manual

Charging electric shutter system
operating instructions

Product information

1. Product Size
   Note: Motor length L subject to product specifications (unit: mm)

2. Product button function
   
   1. Up button:
   ①. Infinite position state: press the motor without action; Long press the motor continuously up, let go and stop.
   ②. Finite position state: press the motor [button up] to open the curtain, then press the motor [Up button] to stop the curtain, and press the button to move and stop in turn until the limit.
   2. Press the button:
   ①. Infinite position state: press the motor without action; Long press the motor continuously downward, release the stop.
   ②. Finite position state: press the motor [down button] to close the curtain, and then press the motor [Down button] to stop the curtain, and press the button to move and stop in turn until the limit.
   3. Battery strip: 7.4V/2200mAh, to power the motor.
   4. Type-c charging port: 5V/1A battery charging port;
   The blue light is on when the motor is charging.

3. Recommended control device
   1.[YR2118B Remote] ①.Led Light
   ②.Right Channel Select
   ③.Up/Open
   ④.Stop
   ⑤.Down/Close| ⑥.Left Channel Selec
   ⑦.Up tilt/75% position
   ⑧.Horizontal 50% position
   ⑨.Down tilt/25% position
   ⑩.Channel setting
   ---|---

2.[Tuya APP]

Basic remote setting

Blocked rotation (motor stroke initialization)

1. When the motor runs for the first time, it needs to carry out blocking. After blocking, the motor will swing once. At this time, the number of turns will be set as the maximum number of turns.

2. After pressing the [Up button] of the motor, the curtain is completely opened and the blocking is completed. Motor stroke initialization is complete.

Setting remote Control Channel

1. At the same time, long press the motor [Up button] or [Down button] for 3 seconds to enter the code learning state.

2. The motor shakes back and forth, and the motor LED indicator lights up.

3. Press the [Channel settings] button on the back of the remotcontrol. The motor vibrates bacand forth, and the LED light flashes 4 times.

Remove remote control channel

1. Long press the motor [Up button] or [Down button] for more than 3 seconds until the LED indicator lights up and enters the code learning state.

2. Press the motor [ Up] or [Down button ] for 7  button seconds, the motor shakes back and forth, the motor LED indicator lights go out, clear all learned remote control channels.

Note: all remote controls cannot control the motor at this time.
Non-contact learning code

1. On the remote control that has learned the code successfully, long press the [Channel setting] key for 4 seconds.

2. The motor shakes back and forth, the motor LED indicator keeps flashing, and enters the state of non-contact remote control learning code.

3. Select the remote control channel, press the [Channel setting] key of the remote control, and the motor shakes back and forth.

4. Press the remote control [Up] button within 4 seconds, and the motor shakes back and forth.

5. Press the remote control [Stop] button within 4 seconds, and the motor shakes back and forth.

6. Press the remote control [Down] button within 4 seconds, and the motor shakes back and forth.

7. Press the remote control [Channel Settings] button within 4 seconds, and the motor shakes back and forth.
   

8. Motor LED off, on behalf of remote learning code success.

Note: after entering the remote control code state, other remote controls cannot interfere with the remote control code.
If no corresponding operation is performed within the specified time, the switch jitter once to exit the remote control learning code state.

Change direction

1. Long press the motor [up button] or [down button] for more than 3 seconds until the LED indicator lights up and enters the code learning state.

2. The motor shakes back and forth, and the motor LED indicator lights up.

3. At the same time, press the [channel left selection] +[Stop] key of the remote control, and the reversing is finished.

4. Motor shake, motor LED indicator light off.

Limits setting

★Note:

1. Stroke setting must be carried out after the complete curtain system (including traction objects, blades, drapes, etc.) is installed.
2.  Remote control is used for travel setting. Due to the inherent characteristics of radio remote control, all motors that can receive the remote control signal may receive the setting instruction during the setting process. Therefore, in order to avoid the misoperation of other curtains, please ensure that irrelevant curtains remain in the power off or invalid state.

Set upper limit

1. At the same time, long press the [Up]+[Channel setting] key of the remote control for 4 seconds to enter the state of setting the upper limit bit stroke.

2. The motor shakes back and forth once. Complete the following operations within three minutes.
   

3. The motor runs to the required upper limit.
   

4. Press the [Channel setting] key of the remote control, the motor shakes back and forth, and the limit point is set.
   

Adjust close limit position

1. At the same time, long press the remote control [Down]+[Channel Setting] key for 4 seconds to enter the state of setting lower limit bit stroke.

2. The motor shakes back and forth once. Complete the following operations within three minutes.
   

3. The motor runs to the required lower limit.
   

4. Press the [Channel setting] key of the remote control, the motor shakes back and forth, and the limit point is set.
   

Connected remote control
Note: After setting the limit point, the motor will be in connected mode

1. Press the [Up] key of the remote control, and the motor runs in the open direction.

2. Press the [Down] key of the remote control, and the motor runs in the close direction.

3. Press the [stop] button of the remote control to stop the motor.

Delete limit

1. At the same time, long press the [Channel Setting]+[Stop] key of the remote control for 4 seconds to clear the trip.

2. The motor shakes back and forth once.

Motor fine stepping

1. Press the remote control [75%] button, and the motor will run in the open direction.

2. Short press the remote control [25%] key, the motor to close the direction of operation.

3. Press the remote control [50%] button to move the motor to the horizontal position.

Intermediate stop setting

Set the intermediate stop point and 3 flush positions
Note: The motor can complete the following operations only when it has a stroke.

1. At the same time, press the [channel setting]+ [75%] key of the remote control, the motor shakes once, and the current position is set as the middle stop point 1. The middle stop bit 1 defaults to 75%.

2. At the same time, press the [channel setting]+ [50%] key of the remote control, the motor shakes once, and the current position is set as the middle stop point 3. Middle stop 3 defaults to 50%

3. At the same time, press the [channel setting]+ [25%] key of the remote control, the motor shakes once, and the current position is set as the middle stop point 2. The middle stop bit 2 defaults to 25%.

4. Long press the [75%] button of the remote control for 1 second, and the motor will stop when it reaches the middle stop point 1. The default is 75%.

5. Long press the [50%] button on the remote control for 1 second, and the motor will stop when it reaches the middle stop point 3. The default is 50%.

6. Long press the remote control [25%] button for 1 second, and the motor will stop when it reaches the middle stop point 2. The default is 25%.

APP control

Automatic network distribution operation

1. Click “+”.

2. Enter the automatic search state.

3. Search out the “charging easy shade”, click “+”.

◆Manual distribution network operation

1. Click “+”.

2. Click “Small Appliances” – “Curtain (Bluetooth)”.

3. Press motor [up button] or [down button] four short and one long confirm.

4. Click “+”.

5. Click “√” – “Next”.

6. Click finish.

◆Basic operation

1. Click “open”, the curtain motor to open the direction of rotation

2. Click “Stop”, the curtain motor stops rotating.

3. Click “Close”, the curtain motor rotates in the direction of closed.

◆Limit Settings

1. Click “Settings”.

2. Click “limit Settings”.

3. Click “ ” to adjust the curtain position upward and click” Set upper Limit “to set the current position as the upper limit of the curtain.

Click ” ” to adjust the curtain position downward, and click” Set lower limit “to set the current position as the lower limit of the curtain.

FCC Caution：
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>