Beba 26914A Dual Flush Valve Instructions

Dual Flush Valve Instruction

Installation Layout

Tip

1. Read all manipulation and installation guideline, and please install it step by step according to the installation guideline and prevent any damage from product breakage and improper use.
2. All material are written according to the latest information when design. Our company reserve the right to change product characterizes, package and supply at any time without notice. 3
3. Do not use corrosive detergent (such as hypochlorite) in water tank because such strong oxidant makes fittings damaged easily and lead to leakage. The mentioned above situations are beyond the range of our guarantee.
4. Our company do not bear the related loses and damages caused by use other company’s parts and material such as glass glue. 5. Suitable temperature range: 0-45°C

Functional Instruction

1. The flush valve has 2 flushing ways: half-flush and full flush; when you push the full flush, the discharge volume is big and when you push the half flush, the discharge volume is small.
2. Water level of half flush is adjustable. (Refer to photo 6) 3. Water level of full flush is adjustable. (Refer to photo 3-2)

Installation Steps

1. Preparation before Installation Remove the old fittings and wash tank before installation. And wash clean because many impurities probably existed in conduit.
   2 .Flush Valve Installation (According to the actual need)
   1. Stainless steel hook for one-piece flush valve installation Contrarotate drainage body and make it remove from pedestal.
   Circumrotate stainless steel hook to the end of bolt clockwise. Let pedestal aim at the water tank scupper, deflect properly, circumrotate, and, the stainless steel hook can reach the scupper downside, then, revise the pedestal, the sealing washer should put upside. Go through the pedestal by the middle finger of left hand to keep off stainless steel hook and make its both sides put around the outfall symmetrically. Circumrotate bolt by screwdriver and be sure that seal between sealing washer and the surrounding for outfall. Let flush valve body insert into pedestal and circumrotate it inside the buckle clockwise.

2. Two-piece flush valve installation Contrarotate drainage body and make it removed from pedestal. Let pedestal insert into outfall from inside of water tank, cover the drainage plastic washer, circumrotate drainage nut and cover the standard washer, and it can adjust the put angle properly according to the actual size of water tank.

Notice: If the product is different from the photo shown, please refer to the actual product.
Let flush valve body insert into Pedestal and circumrotate it inside the buckle clockwise.

Fill Valve Installation

Put fill valve & water-inlet triangle washer insert into water-inlet hole of water tank, then, cover water-inlet tic washer and hexagonal nut in turn from the bottom of fill valve. Fastening water -inlet hexagonal nut and make a proper adjust according to the size of water tank. Adjust water level: Fetch out buckle and screw off water-inlet body anti-dockwise: pull upside or press downside to the proper situation, then, screwing on water-inlet body closely and install the buckle.Little adjustment on water level: revolve adjusted rod to adjust the heOht of water -stop cup and buoy to reach the suitable water !oval viii i moan Connect water-supply ripe and Wilt in adapter or filter according to your actual need. Notice:

1. Be sure that buoy is active freely before M valve installation.
2. Wash the impurity n the condart when you connecting water-supply Pile.
3. The height of water level an not beyond overflow mouth of flush valve when alusting water level.

Water tank Installation

Put water tank on ceramic toilet and make standard washer located at the outfall of toilet. Just the photo shows. let jointed bolt insert into installation hole , then, screw the jointed nut closely.

Examination

As photo show, connect water-inlet pipe to test and notice the following phenomenon:

1. According to the height of half flush to adjust half flush water level: when half flush buoy is higher, the drainage volume is less; when it is lower, the drainage volume is more.
2. Adjust the height of water level by the adjusted digit and its corresponding adjusted patch. The placket is big and its water level is high; the placket is small and its water level is low (Note: When adjusting full flush water level, please fetch out flush valve. then, install flush valve again correctly after adjusted.)
3. Adjust all parts position to prevent them from interference.
4. Open & close for water-stop cup is normal and has no leakage.
5. It is normal for full flush and half flush.

Push button Installation

Screw off push button nut. Let push button insert into water tank lid middle hole, screwing on push button nut from the bottom of water tank lid, then, screwing the adjusted nut closely and be sure that it is firm Please confirm pull flush rod press the flush valve key-press whether or not and check it is blocked or not. Note: Screw off pull flush rod, the cut part is upside. Note: Pull flush rod should aim at the full flush key-press.
Examination Again
Cover water tank lid and notice the following phenomenon to confirm installation complete or not:

1. 0pen & close for water-stop washer is normal and has no leakage.
2. 1t is normal for full flush and half flush and they flush excellently.

Troubele shooting

valve is close
2.Buoy is extrusive by water tank wall. 3.Filter has been blocked owing to bad water quality| 1.0pen the fill valve switch. 2.Adjust fill valve direction.
3.Wash filter (refer to photo 3-1).
Leakage| 1.Fill valve nut is loose.
2.Flush valve does not installed well.
3.Pull flush rod is too long to cling outfall
well (refer to photo 7-4).
4.Flush valve body and pedestal does not match well.
5.Refill water pipe insert into overflow mouth too deep.| 1.Screw the fill valve nut closely.
2.1nstall flush valve again according to its installation step.
3.A.Adjust the adjusted nut (refer to photo 7-2,3,
4): B.Shorten the pull flush rod.A is prior to B. 4.Install again (refer to the installation of flush
valve).
5.Refill water pipe depth can not beyond the height of water level.
No drainage or less drainage| Pull flush rod is too short to press drainage pipe| Adjust adjusted nut (refer to 7-2).
Water level for half flush is too high or too low| Water level does not adjusted well| Adjust water level (refer to photo 6).

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>