TORO 88713 Attachment Pole Hedge Trimmer User Manual

TORO 88713 Attachment Pole Hedge Trimmer

Product Information

• Specifications
  • Form No.: 3460-939 Rev A
  • Model No.: 88713–Serial No. 323000001 and Up
  • Power System: Flex-Force Power SystemTM 60V MAX
• Introduction
  • This pole hedge trimmer attachment is designed for residential homeowners to maintain bushes and hedges.
  • It should only be used by adults and in combination with the Toro Flex-Force Power System 60V MAX Attachment-Capable Power Head Model 51810T.
  • Using this product for purposes other than its intended use can be dangerous.
• Important Note:
  • The included quick-release harness must be installed for proper support and balance.
• Safety-Alert Symbol
  • The safety-alert symbol (Figure 2) is used in this manual and on the machine to identify important safety messages that must be followed to prevent accidents.
• DANGER:
  • Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
• WARNING:
  • Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
• CAUTION:
  • Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
  • This manual also uses two other words to highlight information:
• Important:
  • Calls attention to special mechanical information.
• Note:
  • Emphasizes general information worthy of special attention.

Product Usage Instructions

Please follow the instructions below to properly operate and maintain your pole hedge trimmer attachment:

• Step 1: Assembly
  • Ensure the power head is turned off and disconnected from the power source.
  • Align the attachment drive shaft with the power head coupler.
  • Insert and twist the attachment clockwise until it locks into place.
  • Securely tighten the attachment locking knob.
• Step 2: Installing the Quick-Release Harness
  • Locate the quick-release harness included in the package.
  • Put on the harness by following the provided instructions.
  • Attach the harness to the attachment using the provided hooks or straps.
  • Adjust the harness for a comfortable fit and ensure proper support and balance.
• Step 3: Operating the Pole Hedge Trimmer Attachment
  • Hold the power head firmly with both hands.
• Position the cutting blades near the area to be trimmed.
  • Engage the power head by pressing the power trigger.
  • Maintain a steady grip and move the cutting blades along the desired path to trim bushes and hedges.
  • Release the power trigger to stop the cutting blades.
• Step 4: Maintenance
  • To ensure optimal performance and longevity of your pole hedge trimmer attachment, follow these maintenance guidelines:
  • Regularly inspect the attachment for any damage or wear. Replace any damaged parts before use.
  • Clean the cutting blades and attachment after each use to remove any debris or sap.
  • Apply a small amount of lubricant to the cutting blades and moving parts to prevent rust and ensure smooth operation.
  • Store the attachment in a dry and secure place when not in use.
• FAQ
  • Q: Can I use this pole hedge trimmer attachment with any other power head?
  • A: No, this attachment is specifically designed to be used with the Toro Flex-Force Power System 60V MAX Attachment-Capable Power Head Model 51810T.
  • Q: Where can I find additional information or instructional videos?
  • A: You can visit www.Toro.com/support. for instructional videos or contact your Authorized Service Dealer for assistance.
  • Q: Is the power cord of this product safe to handle?
  • A: The power cord contains lead, which is a chemical known to the State of California to cause birth defects or other reproductive harm. It is important to wash your hands after handling the power cord.
  • Q: How can I access warranty, parts, and other product information?
  • A: If equipped, you can scan the QR code on the serial number plate with your mobile device to access warranty, parts, and other product information. Alternatively, you can contact an Authorized Service Dealer or the manufacturer’s Customer Service.

For assistance, please see www.Toro.com/support. for instructional videos or contact your Authorized Service Dealer before returning this product.

WARNING

• CALIFORNIA Proposition 65 Warning
  • The power cord on this product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
  • Use of this product may cause exposure to chemicals known to the State of
  • California to cause cancer, birth defects, or other reproductive harm.

Introduction

• This pole hedge trimmer attachment is intended to be used by residential homeowners to maintain bushes and hedges. It is to be used only by adults. It is designed to be used in combination with the Toro Flex-Force Power System 60V MAX Attachment-Capable Power Head Model 51810T.
• Using this product for purposes other than its intended use could prove dangerous to you and bystanders.
• Important: You must install the included quick-release harness for proper support and balance.
• Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.
• Visit www.Toro.com. for more information, including safety tips, training materials, accessory information, help finding a dealer, or to register your product.
• Whenever you need service, genuine manufacturer parts, or additional information, contact an Authorized Service Dealer or the manufacturer
• Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided.
• Important: With your mobile device, you can scan the QR code (if equipped) on the serial number plate to access warranty, parts, and other product information.
  1. Model and serial number location
  • Model No.
  • Serial No.

Safety-Alert Symbol

The safety alert symbol (Figure 2) shown in this manual and on the machine identifies important safety messages that you must follow to prevent accidents.

Figure 2 Safety-alert symbol

• The safety-alert symbol appears above information that alerts you to unsafe actions or situations and is followed by the words DANGER, WARNING, or CAUTION.
  • DANGER indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.
  • WARNING indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury.
  • CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
• This manual uses two other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.

The Model 51810T Power Head is compatible with a variety of Toro-approved attachments that, when combined, comply with specific standards; see the following table for more details.

Combination| Power Head Model| Attachment Model| Standard
---|---|---|---
String Trimmer| 51810T| 88716| Conforms to UL STD 82

Certified to CSA STD C22.2 No. 147

Edger| 51810T| 88710| Conforms to UL STD 82

Certified to CSA STD C22.2 No. 147

Pole Saw| 51810T| 88714| Conforms to UL STD 82

Certified to CSA STD C22.2 No. 147

Cultivator| 51810T| 88715| Conforms to UL STD 82

Certified to CSA STD C22.2 No. 147

Hedge Trimmer| 51810T| 88713| Conforms to UL STD 62841-4-2

Certified to CSA STD C22.2 62841-4-2

Safety

WARNING

• Read all safety warnings, instructions, illustrations, and specifications provided with this power tool.
• Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.
• Save all warnings and instructions for future reference.
• The term “power tool” in all the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

IMPORTANT SAFETY INSTRUCTIONS

• Work area safety

1. Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

• Electrical safety

1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
2. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
5. When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
6. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.

• Personal safety

1. Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
2. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions reduces personal injuries.
3. Prevent unintentional starting. Ensure the switch is in the OFF position before connecting to the power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
4. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.
8. Do not let familiarity gained from the frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

• Power tool use and care

1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
2. Do not use the power tool if the switch does not turn on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
3. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
5. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
7. Use the power tool, accessories, tool bits, etc. to these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
8. Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

• Battery tool use and care

1. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
2. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
3. When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
4. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts the eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
5. Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
6. Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C (265 °F) may cause an explosion.
7. Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire. VI. Service
8. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
9. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

• Hedge trimmer safety warnings

1. Keep all parts of the body away from the blade. Do not remove cut material or hold material to be cut when blades are moving. Blades continue to move after the switch is turned off. A moment of inattention while operating the hedge trimmer may result in serious personal injury.
2. Carry the hedge trimmer by the handle with the blade stopped and take care not to operate any power switch. Proper carrying of the hedge trimmer will decrease the risk of inadvertent starting and resultant personal injury from the blades.
3. When transporting or storing the hedge trimmer, always fit the blade cover. Proper handling of the hedge trimmer will decrease the risk of personal injury from the blades.
4. When clearing jammed material or servicing the unit, make sure all power switches are off and the battery pack is removed or disconnected. Unexpected actuation of the hedge trimmer while clearing jammed material or servicing may result in serious personal injury.
5. Hold the hedge trimmer by insulated gripping surfaces only, because the blade may contact hidden wiring. Blades contacting a  “live” wire may make exposed metal parts of the hedge trimmer “live” and could give the operator an electric shock.
6. Keep all power cords and cables away from the cutting area. Power cords or cables may be hidden in hedges or bushes and can be accidentally cut by the blade.
7. Do not use the hedge trimmer in bad weather conditions, especially when there is a risk of lightning. This decreases the risk of being struck by lightning.
8. To reduce the risk of electrocution, never use the extended-reach hedge trimmer near any electrical power lines. Contact with or use near power lines may cause serious injury or electric shock resulting in death.
9. Always use two hands when operating the extended-reach hedge trimmer. Hold the extended-reach hedge trimmer with both hands to avoid loss of control.
10. Always use head protection when operating the extended-reach hedge trimmer overhead. Falling debris can result in serious personal injury.
11. SAVE THESE INSTRUCTIONS

Safety and Instructional

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.

WARNING

• To reduce the risk of injury to persons, remove the battery pack when not in use.
• See the instruction manual for compatible TORO 60v devices and attachments.

Warning— read the Operator’s Manual; wear hearing protection; wear eye protection; wear a hard hat, wear substantial slip-resistant shoes, do not exposed to rain; Caution—Cutting/dismemberment hazard of hands; entanglement hazard—stay away from moving parts; keep bystanders away during operation; Electrical shock hazard—keep away from power lines.

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Connecting the Attachment to the Power Head

1. Install the square shaft of the attachment into the square shaft of the power head (A of Figure 3).
2. Align the locking button on the lower shaft with the slotted hole on the upper shaft and slide the 2 shafts together (B and C of Figure 3).
3. The locking button clicks into the slotted hole when the shafts are secured (C of Figure 3).
4. Using the screw-handle, tighten the screw on the shaft connector until it is secure (D of Figure 3).

Installing the Harness

Connect the metal hook on the shoulder harness to the strap collar on the pole saw handle (Figure 4).

1. Strap adjuster
2. Strap collar
3. Metal strap hook
4. Shoulder strap

The strap length is adjustable; slide the strap adjuster up to decrease the length of the strap, or down to increase the length of the strap (Figure 4). If there is ever an emergency and you need to rapidly remove the harness, disconnect the quick-release buckle as follows:

1. Press in on the sides of the buckle (A of Figure 5).
2. Allow the buckle to disconnect (B of Figure 5).

Product Overview

1. Blades
2. Locking plate
3. Release trigger
4. Adjusting lever
5. Shaft
6. Blade cover

Specifications

Appropriate Temperature Ranges

• Charging time will increase if you do not charge the battery pack within this range.
• Store the machine, battery pack, and battery charger in an enclosed clean, dry area.

Attachments/Accessories

• A selection of Toro-approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com. for a list of all approved attachments and accessories.
• To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous.

Operation

Starting the Attachment

1. Remove the protective cover from the blades (Figure 6).
   • WARNING
   • The hedge trimmer blades can cause cuts or amputation.
   • Be careful when handling the hedge trimmer with the protective cover removed.
2. Ensure that the vents on the attachment, power head, and battery are clear of any dust and debris.
3. Align the cavity in the battery pack with the tongue on the handle housing (Figure 7).
4. Push the battery pack into the handle until the battery locks into the latch.
5. To start the attachment, press the lockout button, then squeeze the run trigger (Figure 8).
   • Note: Slide the 2-speed switch to change the speed of the attachment.
   1. Lockout button
   2. 2-speed switch
   3. Run trigger

Rotating the Hedge Trimmer Head
The hedge trimmer head can rotate 90° for different cutting situations.

1. Remove the battery pack; refer to Removing the Battery Pack from the Power Head (page 12).
2. Press the release trigger and the adjusting lever toward each other and rotate the hedge trimmer head.
3. Release the lever and the trigger, and ensure that the hedge trimmer head and adjusting lever lock into place.
4. Release trigger
5. Adjusting lever

Shutting Off the Hedge Trimmer

• To shut off the hedge trimmer, release the run trigger (Figure 8). Allow at least 5 seconds for the cutting blade to stop moving.
• Whenever you are not using the trimmer or are transporting the trimmer to or from the work area, remove the battery pack and install the blade cover.

Removing the Battery Pack from the Power Head

• Press the battery latch on the machine to release the battery pack and slide the battery pack out of the machine (Figure 10).
  1. Battery latch

Removing the Attachment from the Power Head

1. Ensure that the battery pack is removed from the power head; refer to Removing the Battery Pack from the Power Head (page 12).
2. Loosen the screw-handle on the shaft connector (Figure 3).
3. Press the locking button down while pulling the 2 shafts apart (Figure 3).

Operating Tips

• Use the power tool for cutting in either direction in a slow, sweeping action from side to side.
• When trimming new growth, use a wide sweeping action so that the stems are fed directly into the cutting blade.
• Use a non-powered hand saw or pruning saw to trim stems that are too large.
• If desired, you can use a string to help cut your hedge level. Decide how high you want the hedge. Stretch a piece of string along the hedge at the desired height. Trim the hedge just above the guideline of the string.

Maintenance

After each use of the trimmer, complete the following:

1. Remove the battery pack from the trimmer before maintaining or cleaning.
2. Wipe the trimmer clean with a damp cloth any time there is an accumulation of debris. Do not hose the trimmer down or submerge it in water.
   • WARNING
   • The hedge trimmer blades can cause cuts or amputation.
   • Be careful when handling the hedge trimmer with the protective cover removed.
3. Inspect the machine, and check and tighten all fasteners. If any part is damaged or lost, repair or replace it.
   • Important: Use only the manufacturer’s recommended replacement parts and accessories.
   • Have the product repaired only by an Authorized Service Dealer.
4. Brush debris away from air intake vents and exhaust on the motor housing to prevent the motor from overheating.

Greasing the Hedge Trimmer
Service Interval: Every 10 hours
Grease Type: Lithium–based grease.

1. Place the hedge trimmer on a flat surface and remove the battery pack; refer to Removing the Battery Pack from the Power Head (page 12).
2. Clean the grease fittings with a rag (Figure 11).
3. Connect a grease gun to each of the fittings and pump grease into the fittings until grease flows out from the fittings.
4. Wipe up any excess grease.
5. Grease fitting locations

Lubricating the Blades

Service Interval: After each use
WARNING

• The hedge trimmer blades can cause cuts or amputation.
• Be careful when handling the hedge trimmer with the protective cover removed.

1. Shut off the trimmer, remove the battery pack, and place the trimmer on a flat surface.
2. Clean dirt and debris from the hedge trimmer, using a brush or a damp cloth with a mild detergent.
3. Apply lightweight machine oil (such as #10) along the edge of the top blades (Figure 12).
4. Apply machine oil to the top edge of the blades.

Storage

Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 10).

Important: If you are storing the battery pack for the off-season, charge it until 2 or 3 LED indicators turn green on the battery. Do not store a fully charged or fully depleted battery. When you are ready to use the tool again, charge the battery pack until the left indicator light turns green on the charger or all 4 LED indicators turn green on the battery.

• Disconnect the product from the power supply (i.e., remove the plug from the power supply or the battery pack) and check for damage after use.
• Clean all foreign material from the product.
• Do not store the tool with the battery pack installed.
• When not in use, store the tool, battery pack, and battery charger out of the reach of children.
• Keep the tool, battery pack, and battery charger away from corrosive agents, such as garden chemicals and de-icing salts.
• To reduce the risk of serious personal injury, do not store the battery pack outside or in vehicles.
• Store the tool, battery pack, and battery charger in an enclosed clean, dry area.

Troubleshooting

Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself.

tool.

2.    The battery pack is not charged.

3.    The battery pack is damaged.

4.    There is another electrical problem with the tool.

| 1.    Remove and then replace the battery into the tool, making sure that it is fully installed and latched.

2.    Remove the battery pack from the tool and charge it.

3.    Replace the battery pack.

4.    Contact an Authorized Service Dealer.

The tool does not reach full power.| 1.    The battery pack charge capacity is too low.

2.    The air vents are blocked.

| 1.    Remove the battery pack from the tool and fully charge the battery pack.

2.    Clean the air vents.

The tool is producing excessive vibration or noise.| 1. The blades are dull or damaged.| 1. Contact an Authorized Service Dealer.
The battery pack loses charge quickly.| 1.    The battery pack is over or under the appropriate temperature range.

2.    The machine is overloaded

| 1.    Move the battery pack to a place where it is dry and the temperature is between 5°C (41°F) and 40°C (104°F).

2.    Trim at a slower pace.

Warning Information

California Proposition 65 Warning Information

What is this warning?

• You may see a product for sale that has a warning label like the following:
  • WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov.

What is Prop 65?

• Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
• It mandates that the Governor of California maintain and publish a list of chemicals known to cause cancer, birth defects, and/or other reproductive harm.
• The list, which is updated annually, includes hundreds of chemicals found in many everyday items. The purpose of Prop 65 is to inform the public about exposure to these chemicals.
• Prop 65 does not ban the sale of products containing these chemicals but instead requires warnings on any product, product packaging, or literature with the product. Moreover, a Prop 65 warning does not mean that a product violates any product safety standards or requirements.
• The California government has clarified that a Prop 65 warning “is not the same as a regulatory decision that a product is ‘safe’ or ‘unsafe.’”
• Many of these chemicals have been used in everyday products for years without documented harm. For more information, go to https://oag.ca.gov/prop65/faqs-view-all.
• A Prop 65 warning means that a company has either (1) evaluated the exposure and has concluded that it exceeds the “no significant risk level”; or (2) has chosen to provide a warning based on its understanding of the presence of a listed chemical without attempting to evaluate the exposure.

Does this law apply everywhere?

• Prop 65 warnings are required under California law only.
• These warnings are seen throughout California in a wide range of settings, including but not limited to restaurants, grocery stores, hotels, schools, and hospitals, and on a wide variety of products.
• Additionally, some online and mail-order retailers provide Prop 65 warnings on their websites or in catalogs.

How do the California warnings compare to federal limits?

• Prop 65 standards are often more stringent than federal and international standards. Various substances require a Prop 65 warning at levels that are far lower than federal action limits.
• For example, the Prop 65 standard for warnings for lead is 0.5 μg/day, which is well below the federal and international standards.

Why don’t all similar products carry the warning?

• Products sold in California require Prop 65 labeling while similar products sold elsewhere do not.
• A company involved in a Prop 65 lawsuit settlement may be required to use Prop 65 warnings for its products, but other companies making similar products may have no such requirement.
• The enforcement of Prop 65 is inconsistent.
• Companies may elect not to provide warnings because they conclude that they are not required to do so under Prop 65; a lack of warnings for a product does not mean that the product is free of listed chemicals at similar levels.

Why does the manufacturer include this warning?

• The manufacturer has chosen to provide consumers with as much information as possible so that they can make informed decisions about the products they buy and use.
• The manufacturer provides warnings in certain cases based on its knowledge of the presence of one or more listed chemicals without evaluating the level of exposure, as not all the listed chemicals provide exposure limit requirements.
• While the exposure from the manufacturer’s products may be negligible or well within the “no significant risk” range, out of an abundance of caution, the manufacturer has elected to provide the Prop 65 warnings.
• Moreover, if the manufacturer does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.

Pole Hedge Trimmer Attachment Flex-Force Power System™ 60V MAX Attachment

• Model No. 88713
• Serial No. 323000001 and Up
• Register at www.Toro.com.
• Form No. 3460-939
• Rev A
• © 2023—The Toro® Company
• 8111 Lyndale Avenue South
• Bloomington, MN 55420
• Contact us at www.Toro.com.
• Printed in China
• All Rights Reserved

References

• p65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>