Televes 563832 TWIN HDMI YPbPr MPEG2 4 ENCODER MODULATOR QAM COFDM Installation Guide

Refs. 563832
TWIN HDMI/YPbPr MPEG2/4 ENCODER/MODULATOR – QAM/COFDM
QUICK INSTALLATION GUIDE
www.televes.com

Important safety instructions

Caution Statements

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Only use attachments/accessories specified by the manufacturer.
10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
11. Refer all servicing to qualified service personnel.
    Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Warning
Reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. Safe operation
Should any liquid or object fall into the equipment, please refer to qualified personnel for service.

Safe installation

• Ambient temperature should not be higher than 45°C.
• Do not place the equipment near heat sources or in a highly humid environment.
• Do not place the equipment in a place where it can suffer vibrations or shocks.
• Please allow air circulation around the equipment.
• Do not place naked flames, such as lighted candles on or near the product.

Description of connectors

Front view

1. Power connectors

2. Ethernet connector

3. Ethernet connector

4. Programmer connector

5. RF loop through input

6. RF output

7. YPbPr component input. Channel 1

8. CVBS input. Channel 1

9. Analog (L/R) audio input. Channel 1

10. HDMI input. Channel 1

11. SPDIF digital optical audio input. Channel 1

12. SPDIF digital coaxial audio input. Channel 1

13. SPDIF digital coaxial audio input. Channel 2

14. SPDIF digital optical audio input. Channel 2

15. HDMI input. Channel 2

16. YPbPr component input. Channel 2

17. CVBS input. Channel 2

18. Analog (L/R) audio input. Channel 2

LED indicators

(normal mode).
Slow blinking green| Carrier wave, null, or muted| Output RF channel is OFF or in an alternate signal mode.
Solid orange/red| Normal| Config bitrate doesn´t fit in output
| Color| Output loop status| Comment
LOOP| Solid green| ON| Output loop-through enabled. Units may be daisy-chained using the internal combiner.
Off| OFF| Output loop-through disabled. Units must be combined using an external combiner.
A/V inputs| Indicate the currently selected audio and video inputs and where the input signals should be connected.

Installation

1. Install all units in the rack and connect them as shown in Figure 1.

2. The audio and video input signals connect to the back of the modules (Figure 2).
   If a network is available that provides IP addresses through DHCP, connect the encoders to the network as shown in Figure

3. If such a network is not available, then a computer will need to be connected as shown in Figure 4.

4. Power on the units.

5. Connect the programmer to each unit and set a unique number in the “# ID” field according to the order of installation of the units in the rack (Figure 5).

6. Connect the programmer to a unit, usually the first one, and read the IP address (Figure 6). Each unit can work as a master controller for the other units. All units can be configured by connecting to only one.

7. If a network was connected in Step 3 then proceed to step 8. If not, set the address of you  computer as follows:
   IP value = 172.20.0.2
   netmask = 255.0.0.0
   gateway = 172.20.0.3
   NOTA: The default factory configuration of the units has an IP address in this range (it should be different for each unit). If a unit was ever provided an address before, manually or through DHCP, this unique address may no longer exist. Resetting to IP factory defaults, will return the original unique private address though.

8. In your web browser, enter the IP address from Step 6 as the URL.
   A login prompt will appear. By default the parameters are:
   Login: encoder
   Password: encoder The Status > Summary page should appear as the first page.
   This provides a summary of all the units installed in the network and the units will be sorted by the number entered in Step 5.
   The “Change Password” option only changes the password of the encoder currently logged in to. To change the password for the remaining modules, each one will need to be logged into with its unique IP address and the change made for each.
   Figure 8 shows an example of a detailed status page.

9. Configure all units:
   Select “CONFIGURATION”. This page has 4 options, INPUT, TRANSPORT, OUTPUT, and NETWORK, shown in Figures 9, 10, 11, and 12  respectively.
   For each configuration page, the last column is “Select”. Any changes made, will be saved only to the units with this associated “Select” box checked when “Apply Selected“ is clicked.
   This applies to all 4 of the sections under the Configuration Menu. Some items have an automatic configuration option, such as “Automatic channel numbering” shown in figure 10.
   The network configuration page allows a change to the Number assigned in Step

10. This option also has an “Auto” assignment feature.
    The “Auto” option will ask for confirmation since it will overwrite the settings of all units set in Step 5 and the ordering will likely not be as the units were placed in the rack.

11. Change configuration of one unit:
    Select “CONFIGURATION”. Click on the Model name of the desired unit and the page below will be shown. From this page you can change any parameter of the configuration of the desired unit.

Menu flow chart

For programming Unit operation

• Enable edit mode/Position cursor (in edit mode) /Disable edit mode.
• Change section/Save parameters (press and hold for 3 sec.)
• Change menu/Modify value (in edit mode)

Technical specifications

Reference

|

563832

---|---

INPUTS

| VIDEO| Connectors| 2 sets – 3x RCA for Video (Y, Pb, Pr)
2 sets – 1x RCA for CVBS Video

AUDIO

| ****

Connectors

| 2 sets – 2x RCA for Analog Audio (L, R)
2 sets – 1x RCA for Digital Audio
2 sets – 1x Toslink for Digital Audio (Optical)
VIDEO + AUDIO| Connectors| 2 sets – 1x HDMI
QAM| Connectors| “F” Female (loop-through combiner input)

ENCODING PROFILE

| ****

VIDEO

| Output Format| MPEG-2 / H.264 (1)
---|---|---|---
Resolution| 480i, 480p, 576i, 576p, 720p, 1080i & 1080p (2)

Supports auto-scan for input resolution

Aspect Ratio| 4:3, 16:9, and pass through
GOP| 10, 12, 15, 16, 18, 20, 24 or 30
Transport rate| Variable
Video bit rate| Variable

AUDIO

| Output format| Dolby Digital AC-3 (only digital passthrough) or

MPEG1 Layer2 (analog input or HDMI uncompressed PCM audio)

Sampling rate| kHz| 48
Output bitrate| Variable
OUTPUT| ****

RF

| Connectors| 1x “F” Female
---|---|---|---
Frequency Range| MHz| 46 … 862
Max output level| dBµV| +110 (+100 with loop-through)
Output Attenuator|  |
MER| dB| >40 (typ)
Spurious| dBc| -60
Impedance| Ω| 75
I/Q Phase Error| º| <1
I/Q Amplitude Imbalance| %| <1

QAM

| Modulation format| 16, 32, 64, 128, 256
BaudRate| Mbaud| 6,9
Roll-off| %| 15
Code| Reed Solomon
Spectrum Mode| Normal / Inverted
Frequency Step| KHz| 250

COFDM

| Modulation format| QPSK, 16QAM, 64QAM
Guard Interval| 1/4, 1/8, 1/16, 1/32
FEC| 1/2, 2/3, 3/4, 5/6, 7/8
Bandwidth| MHz| 6, 7, 8
Cell_id| Editable
Frequency Step| KHz| 125 / 166

PSI PARAMETERS

| Transport Stream ID| Editable
Original Network ID| Editable
Network ID| Editable
Logical Channel Number| Editable
NIT Version| Manual / Automatic
SDT Version| Manual / Automatic
Type LCN| Generic / UK / NorDig V1 / NorDig V2
Network Name| Editable
Service PID| Editable
Service Name| Editable
Service ID| Editable

MONITORING / CONTROL

| Local control| Full configuration with LCD handheld programmer
---|---|---

Local monitoring

| LOOP status LED
OUTPUT status LED
TEMP status LED
CH1/CH2 status LEDs
Ethernet status LEDs
Remote monitoring| Centralized web based remote control, management, alarms, and software upgrades
Control| Daisy-chain integrated ethernet switch

GENERAL

| Power supply| Vdc| 24
---|---|---|---
Power disipation| W| <20.4
Operating Temperature| ºF / ºC| 32 to 113 / 0 to 45

1. The reference 563832 is intended to be used to feed several receivers utilizing only an HDMI source. The output quality of the image cannot be considered analogous as that of the original HDMI source.
2. 1080p resolution is only supported with MPEG-4 video codec.

ENCODER DISCLAIMER

1. TELEVÉS states that the following references:
   563803, 563805, 56380501, 56380502, 56380503, 56380504, 56380505, 56380506, 56380507, 56380508, 56380509, 56380510, 563831, 563832, 563833, 563852, 566001, 585301, 585401, hereinafter referred as “Encoder  Equipment” or products.
   have as sole purpose to provide a technical solution to the need to transfer audiovisual content, originally generated in a device provided with an HDMI interface, to one or more receivers located at distances greater than 100 linear  meters within a room or building. According to the currently available technology, it is not possible to conduct the HDMI signal at that distance or greater to a multiplicity of receivers, except through a complex and commercially  non-viable network deployment, which in no case could ensure the protection of the original audio visual content.

2. TELEVÉS, as the holder of an HDCP license, is not entitled to include in a product such as the aforementioned Encoder Equipment any interface, switch, plug, conductor, button, push-button or other equivalent software solution  that allows the output of said content device HDCP decrypted in any analogous form.

3. In order, a) to comply with the license, and b) at the same time provide the purchaser of the product with a technical, legal and feasible solution for the transfer to a multiplicity of receivers at distances greater than 100 linear meters  from the audiovisual signal transmitted with HDMI interface and HDCP encryption, the Encoder Equipments do not allow the output of decrypted audiovisual content in a representation analogous to the HDMI format, but instead  compresses the content of the audiovisual signal, converting it into MPEG format.
   This compressed format allows the transfer of the signal through the use of coaxial cables and its reception through the use of DVB-T / DVB-C / ISDB-T or similar analog tuning interfaces.

4. The user of the products may use the compressed audiovisual format, not analogous to the original HDMI content, in which any of the references cited as Encoders emits its output signal, solely and exclusively for the purpose and  conditions defined as follows: 1st) In order to transfer the signal to content displays (monitors, televisions, projectors) located more than 100 linear meters from the one receiving the HDMI signal with the HDCP encrypted content.
   2º) Provided that the devices that allow the user to view content to which the signal is directed within the premises or building (monitors, televisions, projectors) allow normal viewing of HDMI content while keeping HDCP encryption.

5. Any other use other than that defined in the previous paragraph is expressly prohibited. In particular, the user may not:
   a) Reproduce the signal on content viewers not authorized to reproduce HDMI content while maintaining HDCP encryption; nor,
   b) Carry out conducts or operations aimed at copying, manipulating or transforming, in whole or in part, the audiovisual signal emitted by the products listed in section 1.

6. The user will be solely responsible in the event of improper use of any of the Encoder Equipments or of the audiovisual signal emitted by them. The user will indemnify and hold TELEVÉS harmless, to the maximum extent  permitted by applicable law, against any claim, action or claim, judicial or extrajudicial, from third parties, holders of intellectual or industrial property rights, derived from prohibited actions of in accordance with the previous  provisions.

Click on the “LICENSES” option in the menu bar to get the Licence agreement and Third-parties Software declaration. Also available in: https://doc.televes.com

www.televes.com

References

• Home | Televés

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>