Maraawa KY-2020 2.0 Channel Bluetooth Soundbar User Guide

Maraawa KY-2020 2.0 Channel Bluetooth Soundbar

Check parts and know their function

• will briefly describe the functions of buttons and cables.

1. Power button
2. Mode switch
3. Play / Pause button
4. Volume – / Previous button
5. Volume + / Next button
6. LED Display
7. HDMI ARC(TV) socket
8. OPT socket
9. AUX socket
10. DC IN socket

Power on/off

Power On

1. First, Connect the power cord to the DC IN port on the back of the soundbar.
2.  Next, Plug the other end of the power cord into an AC (mains) power outlet.
3. Press the Power Button for 2 seconds or press the Power Button on the remote control to turn on the Soundbar. The LED display will turn on and you will hear the sound “Power on, Bluetooth Mode”.
4. Press the Mode Switch Button on the soundbar or buttons on the remote control to switch the mode.

Note: For VIP Tech Support or free Lifetime warranty for soundbar and remote. Please contact us at: sales001@swfoeraudio.com.

Power Off

1. First, Turn off the soundbar by pressing the power button on the remote or the power button on the soundbar.
2. Next, Turn off the TV.
   Because many TVs will generate a large audio impact signal when they are turned off, this signal will be transmitted to the soundbar, which will cause a large noise.

Remote Control Usage

BOOST

(The default is normal output when powered on) When the output amplitude of the audio source of the playback device is very small and the output sound of the speaker is very small, click this button to increase the level 1 output volume, and click again to continue to increase the level 2 output volume. Click again to resume normal output.

Warning: This function can only be used when the output amplitude of the audio source of the playback device is very small, otherwise it is not available.

INSTALL THE REMOTE BATTERIES

1. Open the battery compartment cover on the back of the remote.

2. Insert the two AAA 1.5V batteries.
   Note: Please pay attention to the + and – markings inside the compartment.

3. Put the battery compartment cover back into place.

• According to local transportation rules, batteries are not allowed in the package.
• Please prepare 2 AAA batteries for the remote control. Thank you for understanding.”

Connect soundbar with TV

1. Select 1 connection according to your TV slots, such as Bluetooth/HDMI(ARC)/OPT/AUX.
2. Different options are displayed as follows. For a wired connection, only one cable is inserted at a time.

Option 1 (preferred): HDMI eARC or ARC

1. Insert one end of the HDMI cable into your TV’s HDMI eARC or ARC port.
2. Insert the other end of the cable into the HDMI (eARC) port on the soundbar.
3. Short press the Power button on the soundbar to switch modes (or press the “ARC” button on the remote control). You will hear the sound “HDMI Mode”, and the LED Display will show the script ” ARC”.

Note:

1. Insert one end of the HDMI cable into your TV’s HDMI ARC port, not a standard HDMI port.
2. If your TV doesn’t have an HDMI ARC port, it means you can’t use HDMI Connection/need to try other connections because your TV doesn’t support HDMI (ARC).
3. Some TV has 2 HDMI jacks and modes, choose ” HDMI ARC” ONLY.

Note: Please make sure that you insert the HDMI cable into the HDMI ARC port on your TV, not a standard HDMI port. (Some TVs have 2 HDMI jacks and modes, choose “HDMI ARC” ONLY) If your TV does not have an HDMI ARC port then use the Optical Cable.

TV Settings (Different TV has different paths)

• Depending on the method of external audio, go to your TV’s sound settings
• The most commonly set paths for different TVs:
• Path 1 Smart/Home > Settings Sound > Sound Out > External Speaker/External Audio > HDMI(ARC) > Digital Sound Out > PCM
• Path 2 Settings > Sound > Sound Output > Audio Out > HDMI/ARC > Digital Output Audio Form > PCM

Tips: Some TVs require further setup, pls try path 3.
Path 3 Smart/Home > Settings > Audio Output > ARC (HDMI) > Digital Output Format > PCM or Passthrough

• Some TVs require further setup. If there is no sound after connecting, enable HDMI-CEC
• Device Control. Path 4 Settings> Display and Sounds > HDMI-CEC Device Control> On

Optical

If you want to use OPT connection please keep reading, if you want to use other connections, please refer to other pages.

1. Remove the protective cap on both ends of the optical cable.
   CAUTION: Inserting the plug with the cap attached or in the wrong direction can damage the plug and/or the port

2. Insert one end of the optical cable into your TV’s Optical OUT port. After inserting, you should
   see a red LED light on both ends of the port and cable.

3. Hold the plug at the other end of the optical cable.

4. Align the plug with the soundbar’s OPTICAL port, and insert the plug carefully.
   NOTE: The port has a hinged door that swings inward when inserting the plug

5. Firmly push the plug into the port until you hear or feel a click.

6. Short press the Power button on the soundbar to switch modes (or press the “OPT” button on the remote control). You will hear the sound “Optical Mode”, and the LED Display will show the script ” OPT”.

Note: If you do not see a Red LED light on the other end of the optical cable, this means your TV’s Optical port is not working properly, try HDMI ARC, 3.5mm RCA or Bluetooth connection.

TV Settings(Different TV has different paths.)

• Depending on the method of external audio, go to your TV’s sound settings
• The most commonly set paths for different TVs:
• Path 1 Smart/Home > Settings > Sound > Sound Out > External Speaker/External Audio > Optical > Digital Sound Out > PCM
• Path 2 Settings > Sound > Sound Output > Audio Out > Optical > Digital Output Audio Form > PCM

Tips: Some TVs require further setup, pls try path 3.
Path 3 Smart/Home > Settings > Audio Output > Optical > Digital Output Format

PCM or Passthrough

Option 3: AUX

1. Insert one end of the Aux cable into your TV’s AUX port.
2. Insert the other end of the cable into the AUX port on the soundbar.
3. Short press the Power button on the soundbar to switch modes (or press the “AUX” button on the remote control). You will hear the sound “AUX Mode”, and the LED Display will show the script “AUX”.

Note: Use an audio cable to connect to a TV jack labeled “LINE OUT” or “AUDIO OUT” or , not Line IN or Audio IN or Video IN.
Note: Follow the above operation, If there is no sound after connecting, pls try further setting up the TV setting

Tips: Depending on the method of external audio, go to your TV’s sound settings.

1. Settings> Sound> Audio out> Internal TV Speaker> Headset

Option 4: Bluetooth

1. press the “ ” button on the soundbar’s remote into Bluetooth mode.
   You will hear the sound “Bluetooth Mode”, and the LED Display will show the script “BT”.

2. On your device, turn on the Bluetooth feature.
   NOTE: The Bluetooth menu is usually found in the Settings menu.

3. Select “KY-2020” from the list of Bluetooth devices. When Connected, the LED Display will stop ashing and you will hear the sound “Connected”

Note: Long press the “pause” button for 3 seconds to disconnect Bluetooth, then quickly press it again to reconnect (Bluetooth mode only).
Tips: Follow the above operation, If there is no sound after connecting, Please contact us.

LIFETIME WARRANTY

• For VIP Tech Support or a free Lifetime warranty for the soundbar and remote.
• Please contact us at: support@mzeibo.com

TRY THESE SOLUTIONS FIRST
If you experience problems with the soundbar:

• Make sure the soundbar is connected to a live AC (mains) outlet.
• Secure all cables.
• Check the state of the soundbar.
• Move the soundbar within the recommended range of your mobile device for proper operation.

OTHER SOLUTIONS

• If you cannot resolve your issue, see the table below to identify symptoms and solutions to common problems. If you are unable to resolve your issue, contact VIP customer service.
• Please contact us at: support@mzeibo.com.

Troubleshooting

Technical Data

Power supply

• Input: 100 – 240 V~, 50/60 Hz
• Output: 15.0 V 2.0 A
• Remote control: 2 x 1.5 V AAA batteries (supplied NO)

Soundbar

• Output power: 25 W x 2 (50 W)
• Speaker impedance: 53mm / 7 Ω
• Frequency response: 90 Hz – 20 kHz
• Signal-to-noise ratio: 65 dB
• Dimensions (W x H x D): 800 x 60 x 60 mm

Bluetooth

• Bluetooth version: 5.0
• Operating range: 30 feet (10 meters)

Cleaning and Maintenance

Warning!

• Before cleaning, ensure to switch the appliance off and disconnect the power adapter from the electrical outlet.
• Do not use petrol, alcohol or other abrasive cleansers to clean the exterior.
• Clean the exterior with a lightly damp cloth.
• Do not allow liquids to spill into any openings.
• Use the original packaging if it is necessary to transport the appliance.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Wall mounting

1. Align the two (plastic wall parts) with the screw holes on the back of the soundbar,
2. Use a screwdriver to fix the screws (plastic wall mounts) on both sides of the soundbar,
3. Use a screwdriver to fix the screws on the wall respectively,
4. Align the fixed soundbar (plastic wall parts) to the wall of screws, The wall-mounted installation is complete.

Note:
Wall-mounted accessories (plastic wall-mounted parts/screws) are provided.

Preparation
You can place the sound bar on a horizontal surface or mount it on a wall. When mounting it on a wall, pay attention to the following:

• The supplied wall mount brackets can be used to fix the sound bar to a wall. The wall mount brackets are designed for use on vertical walls constructed of solid concrete or bricks.
• When installing on a cinderblock wall, first verify that the blocks have a minimum of 1 inch (2.5 of actual concrete wall thickness to be used for the wall plugs.
• If you are uncertain about the construction of your wall, please consult a qualified contractor or installer for assistance.
• Ensure that the screws you use are strong enough to support the weight of the sound bar and long enough to sufficiently grip the wall.
• Additional tools (not included) are required for the installation.
• Do not overtighten screws.
• Use an electronic stud finder to check the wall type before drilling and mounting.
• During mounting, keep away children and pets.
• Make sure the soundbar is mounted in reach of a wall outlet.

Safety Instructions

1. Follow all safety instructions!

2. Keep the user manual for further use.

3. Before connecting the appliance to the main power supply, check that the power supply voltage and current rating correspond with the power supply details shown on the appliance rating label.

4. Never use an appliance that is damaged! Disconnect the appliance from the power supply and contact your supplier if it is damaged.

5. The danger of electric shock! Never try to repair the appliance yourself. In the event of any malfunction, repairs are to be conducted by qualified personnel only.

6. Warning! The appliance should not be used near water. Do not operate the appliance with wet hands or while standing on a wet floor.

7. Do not open the appliance casing under any circumstances. Do not insert any foreign objects into the inside of the casing.

8. Never use accessories that are not recommended by the manufacturer. They could pose a safety risk to the user and might damage the appliance. You must therefore use original accessories only.

9. The appliance is only suitable for use at moderate degrees of latitude. Do not use in the tropics or in particularly humid climates.

10. Keep the appliance away from any hot surfaces and open flames. Always operate the appliance on a level, stable, clean and dry surface. Protect the appliance against heat and cold, dust, direct sunlight, moisture, dripping and splashing water.

11. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or by those who lack experience and knowledge unless they have been given supervision and instruction concerning the use of the appliance by a person responsible for their safety.

12. Children should be supervised to ensure that they do not play with the appliance.

13. This appliance is classified as protection class II and must not be connected to a protective ground.

14. Regularly check the power plug and power cord for damage. If the supply cord is damaged, the adapter cannot be used and need to be replaced.

15. Avoid damage to the power cord. Do not crush, squeeze, bend, or scour on sharp edges. Keep the power cord away from hot surfaces and naked flames.

16. Lay the cables in such a way that nobody can inadvertently pull them or trip over them.

17. Do not pull the plug out of the socket by the power cord, and do not wrap the power cord around the appliance.

18. If an extension cord is used, its capacity needs to be suitable for the power consumed by the appliance.

19. Connect the power adapter to an easily reachable electrical outlet so that in case of an emergency the appliance can be unplugged immediately. Pull the power adapter out of the electrical outlet to completely switch off the appliance. Use the power adapter as the disconnection device.

20. Disconnect the power adapter from the electrical outlet when not in use and before cleaning.

21. Always switch the appliance off before disconnecting the power adapter.

22. Only use this product with the supplied power adapter.

23. Attention! In the event of a malfunction as a result of electrostatic discharge and momentary electrical surges, unplug the appliance and plug it in again.

24. Make sure that no electrical wires, water, gas or other lines are located around the installation location.

25. Ensure that there is sufficient ventilation. Keep a minimum distance of 4 inches (10 cm) between the appliance and other objects or walls.
    Battery safety instructions

26. Do not expose batteries to extreme temperatures, like direct sunlight or fire.

27. Do not place the remote control on any heat source. Leaking battery acid may cause harm.

28. Always insert batteries correctly about the polarities (+ and –) marked on the battery and the battery compartment.

29. Caution! The danger of explosion if batteries are incorrectly replaced.

30. Replace batteries only with the same or equivalent type.

31. If batteries should leak, remove them with a cloth from the battery compartment.

32. Dispose of batteries according to the regulations. If battery acid has leaked avoid contact with skin, eyes and mucous membranes. Rinse affected areas immediately after contact with the acid and wash with plenty of clean water. Visit a physician.

33. Do not allow children to replace batteries without adult supervision.

34. Batteries shall be stored in well-ventilated, dry and cool conditions.

35. Remove the batteries if you will not be using the appliance for an extended time.

36. The danger of explosion! The battery may not be disassembled, thrown into fire, or short-circuited.

sales001@swfoeraudio.com.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>