ABB M22473-W Video Indoor Station 4.3 Handset Instruction Manual
- June 15, 2024
- ABB
Table of Contents
ABB M22473-W Video Indoor Station 4.3 Handset
Control elements
4.3” colour display Unlock button 2
- In standby status, press to release the 2nd lock of the default outdoor station.
- During a call request or communication, press to release the 2nd lock of the outdoor station that is calling.
- During surveillance, press to release the 2nd lock of the outdoor station which is under surveillance.
Unlock button
- In standby status, press to release the default lock of the default outdoor station. Long press 3 seconds to enable/disable the “Auto unlock” function on the primary indoor station.
- During a call request or communication, press to release the default lock of the outdoor station that is calling.
- During surveillance, press to release the default lock of the outdoor station which is under surveillance.
Surveillance button
- In standby status, press to monitor the default outdoor station.
- During a call request, if “One on” mode is used on the (mini) system controller, only the primary indoor station can show the image, for the secondary indoor station this button needs to be pressed to obtain the image.
- During communication, long press to take a snapshot.
- During surveillance, press to switch to the next video stream or terminate the surveillance.
Mute button
- In standby status, press to activate/mute the ringtone.
- In standby status, long press to mute the ringtone of all indoor stations in the same apartment.
- During a call request, press to activate/mute the ringtone and the call will be terminated after 5 s.
- During communication, press to activate/mute the microphone.
Program button
- In standby status, press to release the 2nd lock of default outdoor station by default. If multiple functions are set to the program button, press to access the “Program button” screen.
Setting button
- In standby status, press to enter the system settings.
- During a call request, communication, or surveillance, press to set the volume, colour, contrast and brightness.
Induction loop function Handset
- During a call request, pick up the handset within 30 seconds to accept the call.
- During communication, hang up the handset to terminate the call.
The function only applies to M22473-W. It is used for hearing-impaired persons. They can wear a hearing aid to hear the voice from the outdoor station or the indoor station.
Terminal description
Default outdoor station address
- Adjust the jumper connector to set the address of the default outdoor station (1-9).
Indoor station selector switch
- Selector switch X10 sets tens digits, selector switch X1 sets unit digits, and Dip switches X100 and X200 set hundreds of digits.
Primary/Secondary indoor station
- Only one indoor station in each apartment can be set as “Primary” (ON=Primary).
Terminal resistor switch
- In video installations or mixed audio and video installations, the switch must be set as ‘RC on’ on the last device of the line (ON=RC on).
- a1, b1 = bus connector
- a potential free contact, such as a doorbell pushbutton
Technical data
- Operating voltage range: 20-30 V ⎓
- Standby current : 24 V ⎓, 6
- Operating current: 24 V ⎓, 150 mA
- Display size: 4.3”
- Display resolution: 480 x 272 pixels
- Single-wire clamps: 2 x 0.28 mm2…2 x 0.75 mm2
- Fine-wire clamps: 2 x 0.28 mm2…2 x 0.75 mm2
- Operating temperature: 5 °C…+45 °C
- Storage temperature: -20 °C…+60 °C
- Size (DxHxW): 206 x 147 x 44.2 mm
INFO
- Go to the online webpage by scanning the QR code.
- Click on the “Downloads” tab to find the documents.
- This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules.
- The complete FCC information is available in the package shipped with the product.
Service
- Find your country contact here.
- http://new.abb.com/contact-centers.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>