LASER NAVC-BHUD-982 CarPlay Screen User Manual

LASER NAVC-BHUD-982 CarPlay Screen

Product Information

Specifications

• Model: NAVC-BHUD-982
• Compatibility: Wireless CarPlay / Android Auto
• Controls and Ports:
  1. AUX port
  2. AV IN (for optional reverse camera)
  3. USB-A port
  4. Micro SD card slot
  5. USB-C power port
  6. Access device Home Screen
  7. Change volume
  8. Enable/disable FM transmission
  9. USB
  10. Bluetooth
  11. Change screen brightness: High, Low, Off
  12. Go back to the previous screen
  13. Switch to Android Auto mode
  14. PhoneLink-Access all CarPlay and Android Auto connectivity options
  15. Access Micro SD card content
  16. Access USB flash drive content
  17. Access FM frequency settings (doesn’t receive FM broadcast stations)
  18. Switch to Apple CarPlay mode

Setting Up

1. Attach the screen to the mounting arm.
2. Remove the protective film from the adhesive suction cup, then press it onto the windscreen. To secure it in place, push the lockdown.
3. Adjust the screen display angle and height so that it won’t obstruct your view of the road, and tighten the knob to secure it.
4. Connect the power adaptor to the car’s cigarette lighter socket and the power port on the screen.
5. Power on the screen.
6. To use the car sound system for audio, tap the FM TX icon on the CarPlay screen. Choose a frequency that is not used by or next to a radio station for best reception. Tune the car radio to the same frequency on the screen, then audio from the screen will play through the car stereo. Alternatively, connect the 3.5mm audio cable to the CarPlay screen’s AUX port and the car’s AUX port. Switch to AUX mode on the car stereo.

Operations – Apple CarPlay

Note: CarPlay requires an iPhone 5 or later running iOS 7.1 or later. Please note that future iOS updates and newer versions may bring changes to CarPlay compatibility or functionality.

Wireless CarPlay Connection:

1. Turn on the screen.
2. Go into Bluetooth pairing mode on your iPhone. Choose NAVC-BHUD. If prompted, enter PIN 0000 and pair.
3. Follow on-screen instructions to grant the necessary permissions (including enabling Siri) and confirm the use of CarPlay.
4. If prompts do not appear after pairing, go to Settings > General > CarPlay > Available Cars, and selectNAVC-BHUD.
5. CarPlay Home screen should appear automatically after a few seconds.

Wired CarPlay Connection

1. Using an Apple-certified Lightning-to-USB cable, connect the iPhone to the USB-A port on the screen.
2. Allow any requests for data sync and confirm to use of CarPlay as USB only.
3. CarPlay Home screen should appear automatically after a fe seconds.

Wired Screen Mirroring

1. On the CarPlay screen, go to PhoneLink > under iPhone, tap on the Auto Connect setting, and set it to Mirror.
2. Using an Apple-certified Lightning-to-USB cable, connect the iPhone to the USB-A port on the screen.
3. Your phone screen will appear on the CarPlay screen after a few seconds.
4. Disconnect the cable to stop screen mirroring and set the Auto Connect setting back to CarPlay.

FAQ:

• Q: Can I use the car power adaptor included with the CarPlay screen to charge my smartphone and other devices?
• A: No, it is not recommended to use the car power adaptor included with the CarPlay screen to charge your smartphone, tablet, and other devices.

WHAT’S IN THE BOX

• 7” CarPlay screen
• 3.5mm to 3.5mm audio cable (for direct connection to vehicle)
• Power cable* (USB-C to 12V cig. socket)
• Extendable windscreen or dash mount
• User manual

WARNING: Do NOT use the car power adaptor included with the CarPlay screen to charge your smartphone, table and other devices.

CONTROLS AND PORTS

1. AUX port
2. AV IN (for optional reverse camera)
3. USB-A port
4. Micro SD card slot
5. USB-C power port
6. Access device Home Screen
7. Change volume
8. Enable/disable FM transmission
9. USB
10. Bluetooth
11. Change screen brightness: High, Low, Off
12. Go back to previous screen
13. Switch to Android Auto mode
14. PhoneLink-Access all CarPlay and Android Auto connectivity options
15. Access Micro SF card content
16. Access USB flash drive content
17. Access FM frequency settings (doesn’t receive FM broadcast stations)
18. Switch to Apple CarPlay mode

SETTING UP

1. Attach the screen to the mounting arm
2. Remove the protective film from the adhesive suction cup, then press it onto the windscreen. To secure it in place, push the lock down
3. Adjust the screen display angle and height so that it won’t obstruct your view of the road, and tighten the knob to secure it.
4. Connect the power adaptor to the car’s cigarette lighter socket and the power port on the screen.
5. Power on the screen.
6. To use the car sound system for audio, tap the FM TX icon on the CarPlay screen. Choose a frequency that is not used by or next to a radio station for best reception. Tune the car radio to the same frequency on the screen, then audio from the screen will play through the car stereo. Alternatively, connect the 3.5mm audio cable to the CarPlay screen’s AUX port and the car’s AUX port. Switch to AUX mode on the car stereo.

OPERATIONS – APPLE CARPLAY

Note:

• CarPlay is compatible with iPhone 5 and later running iOS 7.1 or later.
• Not all iPhone models may support all features of CarPlay.
• Apple periodically updates its software, and newer versions may bring changes to CarPlay compatibility or functionality.
• Siri needs to be enabled for voice control functionality.
• An active phone data plan is required for some functions, like navigation or streaming music.

WIRELESS CARPLAY CONNECTION

1. Turn on the screen.

2. Go into Bluetooth pairing mode on your iPhone. Choose NAVC-BHUD. If

3. Follow on-screen instructions to grant the necessary permissions (including enabling Siri) and confirm to use CarPlay. a. If prompts do not appear after pairing, go to Settings> General > CarPlay > Available Cars,
   and select NAVC-BHUD.

4. CarPlay Home screen should appear automatically after a few seconds.

WIRED CARPLAY CONNECTION

1. Using an Apple-certified Lightningto- USB cable, connect the iPhone to the USB-A port on the screen.
2. Allow any requests for data sync and confirm to use CarPlay as USB only.
3. CarPlay Home screen should appear automatically after a few seconds.

WIRED SCREEN MIRRORING

1. On the CarPlay screen, go to PhoneLink > under iPhone, tap on Auto Connect setting and set it to Mirror.
2. Using an Apple-certified Lightningto- USB cable, connect the iPhone to the USB-A port on the screen.
3. Your phone screen will appear on the CarPlay screen after a few seconds.
4. Disconnect the cable to stop screen mirroring and set Auto Connect setting back to CarPlay

Note: Apple has disabled playback of videos on CarPlay to reduce driving distractions

SWITCHING INTERFACES

1. Tap the Car Home icon to temporarily switch to the screen’s own interface while in CarPlay mode.
2. To return to CarPlay Home screen, tapon the CarPlay icon in the bottom-left corner.
3. To exit out of CarPlay interface, disconnect or forget the Bluetooth connection

OPERATIONS – ANDROID AUTO

Note

• An Android phone with Android 8.0 (Oreo) or higher is needed for wired connection.
• The following devices support wireless connection:
  • Any phone with Android 11.0
  •  A Google or Samsung phone with Android 10.0
  • A Samsung Galaxy S8, Galaxy S8+, or Note 8, with Android 9.0
• Android Auto comes pre-installed on Android 10 and above. For older versions, download the app from the Google Play Store.
• Google periodically updates its software, and newer versions may bring changes to Android Auto compatibility or functionality
• Google Assistant needs to be enabled for voice control functionality.
• An active phone data plan is required for some functions, like navigation or streaming music.

WIRELESS ANDROID AUTO CONNECTION

1. Turn on the screen.
2. Go into Bluetooth pairing mode on your phone. Choose NAVC-BHUD. If prompted, enter PIN 0000 and pair.
3. Follow on-screen instructions (including enabling Google Assistant) to grant the necessary permissions and confirm to use Android Auto.
4. Android Auto Home screen should appear automatically, though it may take up to 30 seconds

WIRED ANDROID AUTO CONNECTION

1. Using a high-quality USB cable, connect the phone to the USB-A port on the screen.
2. Android Auto app should open on your smartphone. Follow on-screen instructions to grant the necessary permissions (including enabling Google Assistant) and allow the app to access features on your phone.
3. Android Auto Home screen should appear automatically after a few seconds

WIRED SCREEN MIRRORING

1. Tap on the PhoneLink icon on the device’s Home screen.
2. Under Android section, set Auto Connect mode to Mirror, and tap on Mirror icon.
3. On your phone, connect to the screen via Bluetooth; Scan the QR code on the screen, and download and install ‘Mirroring’ app.
4. Using a high-quality USB cable, connect the phone to the USB-A port on the screen.
5. Run the Mirroring app on your phone. You phone screen will appear on the display screen.

SWITCHING INTERFACES

1. Tap the ‘Exit’ icon on the Android Auto Home screen to temporarily switch to the screen’s own interface.
2. To return to Android Auto Home screen, tap on the Android Auto icon in the bottom-right corner.
3. To exit out of Android Auto interface, disconnect or forget the Bluetooth connection

BASIC OPERATIONS

ADJUST THE VOLUME

You can adjust the volume in several ways:

• Via the screen’s interface
• The phone when it’s paired to the screen
• The car audio system

On the screen interface, tap the volume icon in the top task bar, then move the slider left or right to adjust the volume.

CHANGE SCREEN BRIGHTNESS

• Go to Setup > Equipment: Display Settings

CHANGE AUDIO EQ SETTINGS

• Go to Setup > Equipment: EQ Setup

MEDIA PLAYBACK VIA USB OR MICRO SD CARD

• Insert a USB flash drive or Micro SD card
• Tap on USB or Micro SD card icon to open its interface.

RESTORE FACTORY SETTINGS

• Go to Setup > Vehicle: Basic Setup > Restore Factory

TROUBLESHOOTING

CANNOT PAIR THE PHONE WITH THE CARPLAY SCREEN

• Bring the phone closer to the CarPlay screen to get better reception.
• Make sure Bluetooth, Wi-Fi and Location Services are turned on.
• If the Bluetooth name of the CarPlay screen doesn’t show on the Bluetooth list, refresh the list or try searching again and wait up to one minute for it to appear.
• If the Bluetooth icon is visible in the top taskbar of the CarPlay device, it is already paired with another phone. To connect a second one, first unpair or disconnect the existing one.
• Check if the phone is already paired with another device like a smartwatch. If so, disconnect or unpair before connecting to the CarPlay screen.
• Turn off the CarPlay screen and turn it on again.
• Turn off the phone and turn it on again.

CARPLAY OR ANDROID AUTO HOME SCREEN DOESN’T APPEAR ON THE SCREEN

• Not all phones support CarPlay or Android Auto. Make sure your phone is compatible.
• For wired connections, ensure that the USB cable is undamaged and securely plugged in on both ends. Try a different Apple-approved or high-quality cable.
• Ensure that necessary permissions and services are enabled on the phone, e.g. Siri, Location services, cellular data, notifications, etc.
• Close apps running in the background.
• Make sure your phone firmware is up to date.
• Restart your phone.

APPS ARE NOT APPEARING OR WORKING

• Only apps that are developed to be compatible with CarPlay/Android Auto will appear and be usable on the screen. Check the App Store or the Play Store for compatibility.
• Make sure the app updates are up to date.
• Ensure that CarPlay/Android Auto and the specific apps are not restricted under Settings.

AUDIO ISSUES

• Ensure the volume on the phone, the CarPlay screen and car stereo is turned up.
• Make sure the 3.5mm audio cable is properly connected.
• In areas with many FM stations, some frequencies might be crowded. Try switching the screen to broadcast on a different FM frequency and match it on your car’s radio.
• Disconnect and reconnect the phone to restart CarPlay or Android Auto

SPECIFICATIONS

file format

Micro SD card| 128GB max.

FAT32 file format

Supported media formats| MP3
Car adaptor power input| 12-24V
Car adaptor power output| 12-24V
Dimensions| 189.7 x 111.6 x 40.5
Weight| 300g

Thank youfor your purchase!Laser Corporation is 100% Australian owned& operated. To get the most out of yourproduct please read the user manualcarefully and keep for future use.For specific information relating to your product such as Spare Parts, FAQs, Warranty claims, and more, please scan the following QR code

Visit our website www.laserco.com.au

Check us out at www.youtube.com/lasercoau

References

• Laser: The Ultimate Tech Hub for Home Entertainment, Audio, ...

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>