VOGUE QIXZOCV 55 Inch Indoor Digital Signage Touchscreen Readable Advertising LCD Panel User Guide

VOGUE QIXZOCV 55 Inch Indoor Digital Signage Touchscreen Readable

Advertising LCD Panel

Product Information

Specifications

• Model: Floor Standing Digital Signage
• Version: V1.0

Attention

1. Before using the digital signage, please refer to the user guide for operation guidance.
2. Avoid splashing liquid on the digital signage.
3. Do not expose the digital signage to direct sunlight.
4. Normal use is protected by our warranty terms, while damage caused by abnormal use is not covered.
5. If you require any support, please contact our after-sales support team.

Accessories
The following accessories are included in the box:

• Body & Base
• Power Cord x 1
• Remote Controller x 1
• M6 Screw x 16
• Cross Screw Driver x 1
• Wheels x 4
• Allen Wrench x 1
• M8 Screw x 6 & Key x 2

Installation Guidance

1. If you want to install wheels, use the cross screwdriver to screw in the 4 M6 screws on each wheel.
2. Place the digital signage body on a bench and install the base. Use the Allen wrench to screw in the 6 M8 screws to secure the base.
3. Position the signage on the floor and connect the power. Turn on the power switch.

Operation Guidance

1. Remote Controller: Use the included remote controller for operating the digital signage.
2. Autoplay Mode: The digital signage will automatically start the Autoplay application. To use this mode, place your media contents into the root directory of a USB flash disk and plug it into the USB port of the digital signage. It will play the media content automatically.
3. Copy Mode: Alternatively, you can make settings on the Autoplay application for Copy Mode. Create a file folder named “AutoPlayFile” on your USB flash disk and place your media contents inside it. When you plug your USB flash disk into the digital signage, it will copy the media contents from the AutoPlayFile to the internal memory of the digital signage. You can then remove your USB flash disk after successful copying.
4. HDMI Input Supported: The digital signage supports HDMI input. You can install your player box inside the digital signage. There is an AC power plug and HDMI input port available inside the door for your player box. Make the necessary settings on the digital signage and select HDMI input in the Auto Start Settings. This will automatically display the HDMI input signal when the digital signage is powered on.
5. Timer Switch: You can use the Timer Switch application to schedule automatic ON/OFF times.

After-sales Support
If you have any technical inquiries or require support, please contact us directly:

• Email: [email protected].
• Phone: 6284885213 (WhatsApp Online), +8618123978547 (WhatsApp Online)

FAQ

• Q: Can I use the digital signage under direct sunlight?
  A: No, it is not recommended to expose the digital signage to direct sunlight.

• Q: How do I play media content on the digital signage?
  A: You can use the Autoplay Mode by placing your media contents into the root directory of a USB flash disk and plugging it into the USB port of the digital signage. It will play the media content automatically.

• Q: Can I install a player box inside the digital signage?
  A: Yes, you can install your player box inside the digital signage. There is an AC power plug and HDMI input port available inside the door for your player box.

• Q: How can I schedule automatic ON/OFF times?
  A: You can use the Timer switch application to set up an auto ON/OFF schedule.

Attention

1. Please check the user guide about the operation guidance before using it.
2. Do not splash liquid on the digital signage.
3. Do not put the digital signage under sunlight directly.
4. Normal use is protected by our warranty terms. Damage caused by abnormal use is not protected by warranty terms.
5. If you require any support from us, please contact our after-sales support team.

Accessories

What’s in Box

Body &Base

Installation Guidance

1. Wheels installation on the base(If you don’t want to install wheels, jump to the next step). Using the cross screwdriver to screw in the 4 M6 screws on each wheel.
2. Put the digital signage body on a bench, and install the base. Use the Allen wrench to screw in the 6 M8 screws to fasten the base.
3. Put the signage on the floor, and get the power connected. And turn the power switch on.

Operation Guidance

1. Remote controller

2. The Autoplay application will start up automatically. The quick starting is the Plug and Play Mode function.
   Put your media contents into the USB flash disk root directory. And plug into the digital signage USB port. It will play the media content automatically .

3. Also you can make settings on the Autoplay application, set with Copy Mode. Set up a file folder named with “AutoPlayFile” on your USB flash disk. Put your media contents into that “AutoPlayFile”. After you plugged your USB flash disk into the digital signage, it will copy the media contents from your USB flash disk “AutoPlayFile” into the digital signage’s internal memory. So that you can plug out your USB flash disk after your media contents was copied successfully to the internal memory.

4. HDMI Input Supported.
   You can install your player box inside of the digital signal. There’s an AC power plug and HDMI input port inside the door available for your player box. Make the settings on digital signage. Set the “Auto Start Settings”, and select the HDMI input, so that it will display the HDMI input signal automatically after the digital signage is powered on.

5. Timer Switch
   You can make an auto ON/OFF schedule on the Timer switch application.

After-sales Support

If you have any technical inquiries, please contact us directly.

1. Email:[email protected]
2. Phone:
3. 6284885213 (WhatsApp Online)
4. +8618123978547 (WhatsApp Online)

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>