GOODWE GW5000-MS-30 Grid Tied PV Inverter Installation Guide

Quick Installation Guide
Grid-Tied PV Inverter
MS Series
(GW5000-MS-30 | GW6000-MS-30
GW7000-MS-30 | GW8500-MS-30 |
GW10K-MS-30 | GW7000-MS-C30 |
GW8000-MS-C30)

Safety Precautions

General Disclaimer

• The information in this quick installation guide is subject to change due to product updates or other reasons. This guide cannot replace the product labels or the safety precautions in the user manual unless otherwise specified. All descriptions here are for guidance only.
•  Before installations, read through the quick installation guide. For additional information, please see the user manual.
• All operations should be performed by trained and knowledgeable technicians who are familiar with local standards and safety regulations.
• Check the deliverables for correct model, complete contents, and intact appearance. Contact the manufacturer if any damage is found or any component is missing.
• Use insulating tools and wear personal protective equipment when operating the equipment to ensure personal safety. Wear anti-static gloves, clothes, and wrist strip when touching electronic components to protect the inverter from damage. The manufacturer shall not be liable for any damage caused by static electricity.
• Strictly follow the installation, operation, and configuration instructions in this guide and user manual. The manufacturer shall not be liable for equipment damage or personal injury if you do not follow the instructions. For more warranty details, please visit https://en.goodwe.com/warranty.

Safety Disclaimer
Warning
DC Side:

1. Ensure the component frames and the bracket system are securely grounded.
2. Connect the DC cables using the delivered PV connectors. The manufacturer shall not be liable for equipment damage if other connectors are used.
3. Ensure the DC cables are connected tightly, securely, and correctly. Inappropriate wiring may cause poor contacts or high impedances, and damage the inverter.
4. Measure the DC cable using the multimeter to avoid reverse polarity connection. Also, the voltage should be under the max DC input voltage. The manufacturer shall not be liable for the damage caused by reverse connection and extremely high voltage.
5. The PV modules used with the inverter must have an IEC61730 class A rating.

AC Side:

1. The voltage and frequency at the connecting point should meet the on-grid requirements.
2. Additional protective devices like circuit breakers or fuses are recommended on the AC side. Specification of the protective device should be at least 1.25 times the rated AC output rated current.
3. Make sure that all the groundings are tightly connected. When there are multiple inverters,make sure that all the grounding points on the enclosures are equipotential bonding.
4. You are recommended to use copper cables as AC output cables. If you prefer aluminum cables, remember to use copper to aluminum adapter terminals.

Product:

1. Do not apply mechanical load to the terminals, otherwise the terminals can be damaged.

2. All labels and warning marks should be visible after the installation. Do not scrawl, damage, or cover any label on the device.

3. Unauthorized dismantling or modification may damage the equipment, the damage is not covered under the warranty.

4. Install the inverter away from high magnetic field to avoid electromagnetic interference.
   If there is any radio or wireless communication equipment below 30MHz near the inverter, you have to:
   • Install the inverter at least 30m far away from the wireless equipment.
   • Add a low pass EMI filter or a multi winding ferrite core to the DC input cable or AC output cable of the inverter.

5. Warning labels on the inverter are as follows.

| HIGH VOLTAGE HAZARD.
Disconnect all incoming power and turn off the product before working on it.| | Delayed discharge. Wait 5 minutes after power off until the components
are completely discharged.
---|---|---|---
| Read through the guide before working on this device.| | Potential risks exist. Wear proper PPE before any operations.
| High-temperature hazard. Do not touch the product under operation to avoid being burnt| | Grounding point. Indicates the position for connecting the PE cable.
****| CE marking| | Do not dispose of the inverter as household waste.Discard the product in compliance with local laws and regulations, or send it back to the manufacturer.

Check before Power-on

and easy-tooperate.
2| The PE, DC input, AC output, and communication cables are connected correctly and
securely.
3| Cable ties are intact, routed properly and evenly.
4| Unused ports and terminals are sealed.
5| The voltage and frequency at the connection point meet the inverter grid connection
requirements.

Declaration of Conformity
GoodWe Technologies Co., Ltd. hereby declares that the inverter with wireless communication modules sold in the European market meets the requirements of the following directives:

• Radio Equipment Directive 2014/53/EU (RED)
• Restrictions of Hazardous Substances Directive 2011/65/EU and (EU) 2015/863 (RoHS)
• Waste Electrical and Electronic Equipment 2012/19/EU
• Registration, Evaluation, Authorization and Restriction of Chemicals (EC) No 1907/2006 (REACH)

GoodWe Technologies Co., Ltd. hereby declares that the inverter without wireless communication modules sold in the European market meets the requirements of the following directives:

• Electromagnetic compatibility Directive 2014/30/EU (EMC)
• Electrical Apparatus Low Voltage Directive 2014/35/EU (LVD)
• Restrictions of Hazardous Substances Directive 2011/65/EU and (EU) 2015/863 (RoHS)
• Waste Electrical and Electronic Equipment 2012/19/EU
• Registration, Evaluation, Authorization and Restriction of Chemicals (EC) No 1907/2006 (REACH)
  You can download the EU Declaration of Conformity on www.goodwe.com.

LED Indicators
Inverters Designed with LCD

Inverters Designed without LCD

Product Introduction

Parts

1. DC switch Locking Hole [1] Communication
Module/RS485-USB
4. Cable Port/USB
Communication Port
7. AC Output Terminal
10. LCD(optional)
13. Heat Sink| 2. DC Switch
RS485/Remote Shutdown/
5. CT/Meter Communication Cable Port
8. PE Terminal
11. Button(optional)| 3. PV Input Terminal [2] DRED/Dry Contact
6. Communication
Cable Port
9. Indicator
12. Mounting Plate
---|---|---
[1] For Australia only.
[2]:GW7000-MS-C30/GW8000-MS-C30: 2x PV+/PV-. Others: 3x PV+/PV-.

Dimensions

Inverter Installation

Space Requirements

Angle Requirements

Installing the Inverter

Electrical Connection

PE Cable

AC Cable

DC Cable

Devalan

MC4

Communication Connection

(For Australia
only)| COM/DRMO
6| 1/03+| 16| REFGEN
7| 1/02-| 17| DRM4/8
8| 1/02+| 18| DRM3/7
9| 1/01-| 19| DRM2/6
10| I/01+| 20| DRM1/5

Communication Module

WiFi kit, LAN kit, 4G kit, GPRS, Bluetooth Kit, Wi-Fi/LAN Kit module: optional.

RS485-USB Cable(Optional): Brazil.

Power On and Off

Commissioning

Commissioning via LCD

Commissioning via SolarGo APP

http://www.sems.com.cn/home/solargo

Monitoring via SEMS Portal App

https://www.semsportal.com/home/AppDownload

For more detailed instructions, scan the QR codes below.

|
---|---
https://www.goodwe.com/Form/column?tpl=downloadcenter &documenttype=%E7%94%A8%E6%88%B7%E6%89%8B%E5%86%8C&productmodel=DNS%20G3%E7%B3%BB%E5%88%97| https://en.goodwe.com/Public/Uploads/sersups/WiFi%20Configuration%20Instruction.pdf
|
https://en.goodwe.com/Public/Uploads/sersups/User’s%20Guide%20of%20SolarGo%20App.pdf| https://en.goodwe.com/Ftp/EN/Downloads/User%20Manual/GW_SEMS%20Portal-User %20Manual- EN.pdf

https://en.goodwe.com/

|
---|---
340-00821-01| https://en.goodwe.com/contact- us.asp

GoodWe Technologies Co., Ltd.
No. 90 Zijin Rd., New District, Suzhou, 215011, China
www.goodwe.com
service@goodwe.com

References

• GoodWe Warranty
• GoodWe: Smart Energy Innovator
• GoodWe: Smart Energy Innovator
• GoodWe Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>