JESLED T8 LED Light Fixture Instruction Manual

 T8 LED Light Fixture

T8 LED Light Fixture
Web:www.Jesled.com 

PACKAGE CONTENTS

Note: Hardwares are not shown actual size.

SPECIFICATIONS

Model No| S1ze| Langth| Input| Curint Rating| Maximum number of units to be
interconnected| Life  (Nom)
---|---|---|---|---|---|---
S T800
1863060|  2 T| 2 A6″| 120 ac 50/60Hz| 018A| 4 cs| >50 Hrs00
S T818
2763090| 3 T| 3 .39″| 0 27A| 4 cs|  >50 Hit00
S T827
3663120|  4 T| 4 .2″| 0 36A| 4 cs| >5Hrs000
S T800
4564120| 4 T| 4 .2″| 0 45A| 4 cs| >5000 H it
S T836
45133150| 5 T| 5 .02″| 0 45A| 4 cs| >5000 Hrs
S 1845
5463180|  6 T| 6 .45″| 0 54A| 4 cs| >50 Hrs00
S T854
7263240| 8 T| 9 .07″| 0 72A| 4 cs| >5000 Hrs
S T845
9064240| 8 T| 9 .07″| 0 9A| 4 cs| >5000 Hit

PEPARATION

Before beginning assembly, installation or operation of the product, make sure all parts are present.
Compare parts with package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts.
Tools Required for Assembly (not included): Screwdriver, Pliers, Electrical Tape, Wire Cutters, Safety Glasses, Ladder, Wire Stripper.
Estimated Assembly Time: 15 minutes

PLUG & PLAY
Email: support@jesled.com
WARNING
– SUITABLE FOR DAMP LOCATIONS ONLY.
– DO NOT LOOK DIRECTLY AT LED LIGHT SOURCES.
– THIS PRODUCT IS INSPECTED PRIOR TO SHIPPING. DO NOT USE IF PRODUCT IS CRACKED, BROKEN OR LACKING OF PARTS.
– SUITABLE FOR USE IN OPERATING ENVIRONMENTS RANGING BETWEEN -4° TO 104°F (-20° TO 40° C).
– LIFETIME OF THIS PRODUCT MAY BE REDUCED WITH PROLONGED EXPOSURE TO EXTREME TEMPERATURES.
– BO NOT ANCHOR CORD WITH STAPLES, NAILS, OR SIMILAR OBJECTS TO AVOID PUNCTURE AND DAMAGE TO THE CORD.
– DO NOT COVER THIS PRODUCT AS THE COVERING MAY CAUSE THE LIGHTS TO OVERHEAT OR IGNITE.
– DO NOT USE IF THERE IS ANY DAMAGE TO THE LIGHT OR CORD INSULATION. INSPECT PERIODICALLY.
– DO NOT INSTALL THE LIGHTING NEAR FLAMMABLE LIQUIDS.
– DO NOT INSTALL ON DOORS OR GATES WHERE REPEATED FLEXING CAN OCCUR.
– DO NOT USE WITH DIMMERS
– ENSURE ALL CONNECTIONS AND THE CAP ARE SECURED.

ASSEMBLY INSTRUCTIONS

Important to know

1. Read all instructions carefully before installation and operation.
2. Do not use in wet locations, indoors only.
3. Non-replaceable LEDs.
4. Caution: Avoid looking directly into the light source for prolonged periods to avoid eye damage.
5. Not to be used with a dimming circuit or any other electronically controlled switch.
6. If you are not familiar with state and local electrical codes, it is recommended that you consult with a qualified electrician.

Installation steps

1. Turn off the power at fuse or circuit box.

2. Select suitable location that can support the weight of the fixture. Determine method of mounting before drilling.
   Make two spots 32 in. apart for the mounting hardware (See Figure 1). Wear safety glasses before drilling pilot holes.
   

3. Screw the Mounting Bracket (A) with the Screw (C) and Plastic Anchor (D) provided. (See Figure 2)

4. Push the led light fixture into the brackets, make it stable. (See Figure 3)
   

5. Connect power by Power Cord (F) or Power Switch Cord (H) provided. (See Figure 4 and Figure 5)
   

6. The LED light fixtures can be linked together in series using the Connector (B) or Extension Cord (G) provided. Maximum linkable up to 4pcs fixtures. (See Figure 6 and Figure 7)

7. Intall the End Cap (E) at the end of light fixture to prevent dust.

8. Turn on the power at fuse or circuit box and test the light.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>