CKB TE-5975CH Tampa Single Sliding Frameless Bathtub Shower Door Installation Guide

Orbit 56545 1 Dial 4 Outlet Hose Faucet Timer

General Information

Inspect the product immediately upon receipt for transit damage, missing packs/parts or manufacturing fault. Damage reported later will not be accepted. Handle the product with care avoiding knocks and shock loading to all sides and edges of the glass.

Notes: Safety glass can not be re-worked

Read these instructions carefully before start of installation.
Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: This product is heavy and may require two people to install.

Aftercare instructions

After use, your shower should be cleaned with soap and water. This is particularly important in hard water districts where insoluble lime salts maybe deposited and allowed to build up.
Cleaners of a gritty or abrasive nature should not be used. Care should be taken to avoid contact with strong chemicals, they can be used but with caution, if in doubt contact the manufacturer of the cleaner in question.
Keep these instructions for aftercare and customer service details.

Note: Stainless steel top rail can be trimmed up to 4″ for width adjustment. If installation opening is smaller, the overlap of two glass panel is bigger, and the entrance size is reduced accordingly.

Tools Required

• Silicone

• Level

• Drill

• Drill Bit

• Screwdriver (Phillips)

• Sealant Finishing Tool

• Mallet

• Pencil

• Tape Measurer

• Allen Wrenches

• Painters Tape

Tips: Measure the finished opening before proceeding with the installation to be sure that the correct model size has been ordered.
Note: These instructions will show the installation of the shower door.
Please follow the same steps for the installation of the tub door.

PARTS LIST A

FOR SHOWER/BATHTUB DOOR (8MM)

PACKING LIST

Keep small parts away from children

PACKING| DESCRIPTION| Q’TY| PART#| DESCRIPTION| Q’TY
---|---|---|---|---|---
1| Wall Plugs| 10pcs| 10| Gasket-B for 5/16″(8mm) Glass| 1pc
2| Wall Jamb| 1pc| 11| Handle| 1pc
3| Screws ST4x1 3/8″A| 6pcs| 12| Square Wall Joints Whit Plastic Bumper| 2pcs
4| Fixed Panel| 1pc| 13| 5/8″ Plastic Bumper| 1pc
5| Door Panel| 1pc| 14| Top Rail| 1pc
6| Bottom Guide x 1| 1set| 15| Glass Fixing Piece| 2pcs
Screws ST5x1 3/8″ x 2| 16| Roller| 2sets
Wall Plugs x 2| 17| Lock In Knob Sets| 2sets
7| Gasket-A for 5/16″(8mm) Glass| 1pc| 18| Gasket-C for 5/16″(8mm) Glass| 2pcs
8| Aluminum Bottom U Channel| 1pc| 19| Screws ST4x 1 3/8″B| 4pcs
9| Cover Strip Profile| 1pc| 20| Allen Wrench| 3pcs

FOR SHOWER/BATHTUB DOOR (10MM)

PACKING LIST

Keep small parts away from children

PART#| DESCRIPTION| Q’TY| PART#| DESCRIPTION| Q’TY
---|---|---|---|---|---
1| Wall Plugs| 10pcs| 10| Gasket-B for 3/8″(10mm) Glass| 1pc
2| Wall Jamb| 1pc| 11| Handle| 1pc
3| Screws ST4x1 3/8″A| 6pcs| 12| Square Wall Joints Whit Plastic Bumper| 2pcs
4| Fixed Panel| 1pc| 13| 5/8″ Plastic Bumper| 1pc
5| Door Panel| 1pc| 14| Top Rail| 1pc
6| Bottom Guide x 1| 1set| 15| Glass Fixing Piece| 2pcs
Screws ST5x1 3/8″ x 2| 16| Roller| 2sets
Wall Plugs x 2| 17| Lock In Knob Sets| 2sets
7| Gasket-A for 3/8″(10mm) Glass| 1set| 18| Allen Wrench| 3pcs
8| Aluminum Bottom U Channel| 1set| 19| Screws ST4x 1 3/8″ B| 4pcs
9| Cover Strip Profile| 1set| | |

INSTALLATION STEPS

STEP 1A

STEP 1B

Model Width – Finished Opening(Width) = Cut Off Length

*This Shower Door Can Be Installed At Wall Opening From 59 ” (No Need Cut Rail).

STEP2

STEP3

STEP4

STEP 5

A: Installation size width less than 59″, use 1/4″ plastic bumper as shown.

B: Installation size up to 59″, use 5/8″ plastic bumper on fixed panel side as shown.

STEP6

Adjust top rail until it level.

Table

STEP 7 FOR 8MM GLASS

STEP 7 FOR 10 MM GLASS

This bottom guide is pre-installed for mm glass. To install mm glass, please take out the plastic insert block, install the insert block according to the marked position as shown on diagram before going to next step.

STEPS 8

STEP 9

STEP 10

Carefully slide the door toward the wall and check the door is sliding smoothly.
Adjust if necessary using offset in rollers, so that the sliding door is parallel to the tray.

HOW TO ADJUST

Step 1 : Loosen center bolt with hex wrench
Step 2: Rotate to adjust panel angle with hex wrench
Step 3 : Tighten center bolt

STEP 11

Please note to get correct gasket seals for different glass thick configuration.

STEP 12

Apply clear silicone caulking along the wall and threshold of the shower door inside and outside.
(make sure you) wait 24 hours before using the shower. Do not allow water to directly hit door.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>