ARROW FASTENER T2025 Staple Gun Instruction Manual
- May 15, 2024
- ARROW FASTENER
Table of Contents
ARROW FASTENER T2025 Staple Gun
Product Specifications
- Brand: Arrow Fastener Co.
- Model: T2025TM
- Staple Sizes: 6mm, 5mm
Product Usage Instructions
Safety Rules
- Remove the pusher rod from the machine.
- Insert a strip of staples.
- Replace the pusher rod.
- Remove the pusher rod.
- Remove the screw and nut from the designated hole.
- Pull down the entire inside frame for complete cleaning.
To determine staple shortage for a refill
- Press the latch to release the pusher rod.
- Lightly push the rod forward until it stops. The visible projected part of the rod indicates the remaining staples in the track.
About Staples
For best penetration, raise the rear of the gun slightly off the work and bear down on the front end to prevent recoil when operating.
Determining Proper Staple Leg Size
- Measure the thickness of the material to be tacked and allow approximately 3/16 for penetrating wood.
- Adjust staple leg length accordingly for better results.
- Refer to the provided figures for different wire positions and flat crown stapling.
Maintenance
For maintenance inquiries, contact Arrow Fastener Co., LLC at the provided address and telephone number.
Frequently Asked Questions (FAQ)
Q: How often should I clean the staple channel?
- A: It is recommended to clean the staple channel periodically, especially when switching between staple sizes or experiencing jamming issues.
Q: Can I use other staple sizes with this stapler?
- A: The T2025TM model is designed for use with 6mm and 5mm staples. The use of other sizes is not recommended as it may affect performance and safety.
SAFETY RULES
- Always be cautious of potential hazards such as electrical wiring, slippery footing, damp conditions, etc.
- Make sure you know what you are fastening — look for hidden hazards.
- Keep the work area clean. Cluttered areas and benches invite accidents.
- Keep children away. All visitors should be kept at a safe distance from the work area.
- Store idle tools. When not in use, tools should be stored in a high or locked-up place — out of reach of children.
- Use safety glasses.
- Do not overreach. Keep proper footing and balance at all times.
- Maintain tools with care. Follow instructions with care.
- For service, use only approved service centers.
- Use only the original parts provided by the supplier.
- Stay alert — watch what you are doing. Use common sense.
- Do not staple into electrical wires. Be cautious of wires that may be hidden from view. Disconnect circuits.
HOW TO LOAD STAPLES
TO LOAD
- Remove the pusher rod from the machine.
- Insert a strip of staples.
- Replace the pusher rod.
TO CLEAN STAPLE CHANNEL
- Remove pusher rod A.
- Remove the screw and nut from hole B.
- Pull down the entire inside frame for complete cleaning.
HOW TO DETERMINE STAPLE SHORTAGE FOR REFILL
- Press the latch to release the pusher rod.
- Lightly push the rod forward until it stops. The visible projected part of the rod indicates the amount of staples remaining in the track.
ABOUT STAPLES
STAPLE PENETRATION
- For best penetration with any gun tacker, raise the rear of the gun slightly off the work and bear down on the front end to prevent recoil when operating.
- The power spring on the T2025™ will drive well into all ordinary woods. If the wood is very hard and the staple is not driven flush, use a shorter staple size.
- A shorter staple leg will hold better in hardwood than a long leg in softwood.
HOW TO DETERMINE THE PROPER STAPLE LEG SIZE FOR WIRE OR STAPLING
- Measure the thickness of the material to be tacked and allow approximately 3/16″ for penetrating wood.
- A staple that stands away from the material simply means too long a leg length has been used.
- Try the next shorter leg length for better results.
- Congratulations on your purchase of an Arrow® T2025™ Staple Gun Tacker, the “Attacker.
- Once you become familiar with its Height Guide*, you will find that the T2025™ “Attacker” is a very versatile tool. Unique to the “Attacker” is its built-in Height Guide and its ability to shoot both round T25™ staples and flat T20™ staples.
- When the guide is in its lowest position, as indicated by the arrow (Fig. 1), it will staple round or flat wires up to 1/4″ 6mm in Dia.
- Move the “finger-shifter” one notch to the right, and it will safely staple flat or round wire 1/8˝ 3mm in Dia. with T25™ staples (Fig. 2).
- Move the finger-shifter” one more notch to the right, and it will staple the T20 flat crown staples. (Fig. 3).
Round Crown Staple
- Use T25™ Staples Only
Narrow Flat Crown Staple
- Use T20™ Staples Only
MAINTENANCE
- Arrow Fastener Co., LLC
- 271 Mayhill Street, Saddle Brook, N.J. 07663 Tel. 201-843-6900
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>