Edge-corE ECS5520-18X 16-Port L2+-L3 Lite 10G Switch with Two 40G Uplinks User Guide

Edge-corE ECS5520-18X 16-Port L2+-L3 Lite 10G Switch with Two 40G Uplinks

Package Contents

1. ECS5520- l 8X or ECS5520- l ST (with l AC PSU)
2. Rack Mounting Kit- 2 brackets and 8 screws
3. Four adhesive rubber feet
4. Power cord
5. Console cable- RJ-45 to DB-9
6. Documentation- Quick Start Guide (this document) and Safety and Regulatory information

Mount the Switch

1. Attach the brackets to the switch.
2. Use the screws and cage nuts supplied with the rack to secure the switch in the rack.

Note: The switch can also be installed on a desktop or shelf using the included adhesive rubber foot pads.

Ground the Switch

1. Ensure the rack on which the switch is to be mounted is properly grounded and in compliance with ETSI ETS 300 253. Verify that there is a good electrical connection to the grounding point on the rack (no paint or isolating surface treatment)
2. Attach a lug (not provided) to a #18 AWG minimum grounding wire (not provided), and connect it to the grounding point on the switch rear panel. Connect the other end of the wire to the rack ground.

• Caution: The earth connection must not be removed unless all supply connections have been disconnected.
• Attention : Le raccordement a la terre ne doit pas etre retire sauf si toutes les connexions d’alimentation ont ete debranchees.
• Caution: The device must be installed in a restricted access location. It should have a separate protective earthing terminal on the chassis that must be permanently connected to the earth to adequately ground the chassis and protect the operator from electrical hazards.

Connect Power

a. Connecting AC Power

1. Install one or two universal AC PSUs in the switch.
2. Connect an external AC power source to the PS Us.

Note: For international use, you may need to change the AC line cord. You must use line cord sets that have been approved for the socket type in your country.
b. (Optional) Connecting DC Power

1. Install one or two DC PSUs in the switch.
2. Connect the DC power supply wires to the supplied connector as follows:
   • A – Blue Wire: DC Return
   • B – Brown Wire: -36 – -72 VDC
   • C- Yellow Wire – Chassis Ground
3. Insert the DC supply connector into the DC PSU power input socket.

• Caution: Use a UL/IEC/ EN 60950-1 certified power supply to connect to a DC converter, and a # 14 AWG wire to connect to a DC PSU.
• Attention : Utilisez une alimentation certifiee UL/IEC/EN 60950-1 pour le connecter a un convertisseur CC et un cable AWG # 14 pour vous connecter a une alimentation CC.

Verify Switch Operation

1. Verify basic switch operation by checking the system LEDs.When operating normally, the PSU l / PSU2 and the DIAG LED should all be green.

Perform Initial Configuration

1. At this point, you may need to make a few basic switch configuration changes before connecting to the network. It is suggested to connect to the switch console port to perform this task.
2. The serial port’s configuration requirements are as follows: l 15200 bps, 8 characters, no parity, one stop bit, 8 data bits, and no flow control.
3. You can log in to the command-line interface (CLI) using default settings: User “admin” with password “admin”.
4. For information on initial switch configuration, refer to the CU Reference Guide.

Connect Network Cables

1. For the SFP/S FP + /QSFP+ slots, first install SFP/ SFP+/QSFP+ transceivers and then connect fiber optic cabling to the transceiver ports. The following transceivers are supported:
   • l 000BASE-SX (ET4207-SX)
   • l 000BASE-LX (ET 420 l -LX)
   • l 0GBASE-SR (ET5402-SR)
   • l 0GBASE-LR (ET5402-LR)
   • 40GBASE-SR4 (ET6407-SR4)
   • 40GBASE-LR4 (ET640l-LR4)
2. As connections are made, check the port status LEDs to be su re the links are valid:
   • On/ Blinking Green – Port has a valid link. Blinking indicates network activity

Hardware Specifications

Switch Chassis

• Size (WxDxH): ECS5520- l BX: 43.8 x 28.0 x 4.3 cm (17 .26 x 11.02 x 1.71 in.)
  • ECS5520- l ST: 44.0 x 28.0 x 4.4 cm (17.32 x 11 .02 x l .73 in.)
• Weight
  • ECS5520- l 8X: 3.9 kg (8 .6 lb) with l PSU
  • ECS5520- l 8T: 4. l kg (9 .04 lb) with l PSU
• Temperature
  • Operating: 0° C to 50° C (32° F to 122° F)
  • Storage: -40° C to 70° C (-40° F to 158° F)
• Humidity
  • Operating: 5% to 95% (non-condensing)

AC PSU Power Specification

• AC Input Power l 00- 240 VAC 50- 60 Hz, 3- 1 .5 A
• PSU Power Rating l 50 W x 2 AC PSU
• DC PSU Power Specification
• DC Input Power: 36- -72 VDC, 6- 3 A
• PSU Power Rating – l 50 W x 2 DC PSU

Regulatory Compliances

• Emissions
  • AS/ NZS CISPR 32:2015 EN 61000-3-2: 2014, Class A EN 61000-3-3: 2013 FCC, Class A VCCI, Class A CNS 13438 GB/T9254-2008
• Immunity
  • EN55032: 2015/AC:2016
  • EN55024:2010+ Al:2015
• Safety
  • IEC 60950-1 :2005 +A l :2009 + A2:2013 IEC 62368-1 :2014 UL 62368-1, 2014 -12-l, CAN/CSA C22 .2 No.62368-1-14, 2014-12 BSMI Safety Standard CNS 14336-l GB4943. l -201 l
• Taiwan RoHS: CNS 15663

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>