WUBEN X-1 Falcon Flashlight User Manual
- June 15, 2024
- WUBEN
Table of Contents
- WUBEN X-1 Falcon Flashlight
- Packaging
- About The Flashlight
- Clamp Instalation
- Operation Of The Flashlight
- Programming Mode
- Restore Factory Settings
- Charging
- Maintenance
- Specifications
- Common Issues and Solutions
- Warranty Conditions
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
WUBEN X-1 Falcon Flashlight
Dear customer,
Thank you for purchasing our product. Please read the following instructions
carefully before first use and keep this user manual for future reference. Pay
particular attention to the safety instructions. If you have any questions or
comments about the device, please contact the customer line.
www.alza.co.uk/kontakt
✆ +44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7,
www.alza.cz
Packaging
Before using this product, please check whether the contents of the package are complete.
About The Flashlight
Clamp Instalation
Operation Of The Flashlight
- Power On/Off: Click the button to turn on the flashlight, and click again to turn it off. The flashlight features brightness memory, except for the flashing mode and Turbo mode.
- Default Output Selections: While the flashlight is on, press and hold the button to cycle through the brightness levels: Eco-Low-Med-High-Eco (cycling). Release the button at any level to lock the brightness.
- Instant Turbo: Regardless of the current state, quickly double-click the button to activate the Turbo mode.
- Instant Low: While the flashlight is off, press and hold the button to enter the energy-saving mode.
- Flash Modes: In any state, triple-click the button to enter the flash mode. Triple-click again to cycle through the flash modes: SOS-flash.
- Lockout/Unlock: When the flashlight is turned off, press the button four times. The flashlight will flash three times, indicating that it is locked. Press the button, and the indicator will flash three times. Press the button four times again, and the energy-saving mode will activate, indicating that the lock is released.
Programming Mode
In the respective corresponding modes, click and hold the switch to gradually adjust the brightness within the range. Once the maximum or minimum brightness is reached, the flashlight will flash once. Release the button to lock the current brightness level, and the flashlight will remember this brightness for that specific mode.
Mode | Brightness |
---|---|
Eco | 20 – 4000 Lumens |
Low | 400 – 1000 Lumens |
Medium | 1000 – 2000 Lumens |
High | 2000 – 3000 Lumens |
Restore Factory Settings
To restore the flashlight to its factory settings, follow these steps: while in the locked state, click the switch “W” every 0,5 seconds, double-click the key every 0,5 seconds, and hit the key three times. This action will activate the factory setting, causing the flashlight to turn on at the lowest brightness level. This signifies that the key lock has been released, and the flashlight’s factory default brightness has been successfully restored.
Charging
Battery Capacity Indication
Maintenance
- Use WUBEN or recommended batteries.
- Charge or replace the battery promptly when low power is indicated to preserve battery durability.
- Store the product in a dry and well-ventilated area.
Specifications
Mode | Turbo | High | Medium | Low | Eco | Strobe | SOS |
---|---|---|---|---|---|---|---|
Brightness | 12000 – |
3000 lm
| 2600 lm| 1000 lm| 400 lm| 20 lm| 3000 lm| 200 lm
Run Time| 1 m + 1,7 h| 2 h| 5,5 h| 14 h| 220 h| /| /
Light
Source
| | | 3× Cree XHP70.2| | |
Distance of
Beam Projection
| | | ****
303 m
| | |
Intensity of Light
Source
| | | ****
23000 cd
| | |
Drop
Resistance
| | | 1 m| | |
Water
Resistance
| | | IP55| | |
Weight| | | 379 g With Battery| | |
Dimensions| | | 128,5×56×28 mm| | |
In accordance with the ANSI/NEMA FL1 standard, the provided data has been tested in our laboratory using two 21700 4800mAh batteries developed internally. Please note that the data may vary due to differences in test environments and batteries.
Common Issues and Solutions
Issue: Abnormal Flashing or Failure to Turn On
Possible Causes:
- The flashlight may be in lockout mode.
- The switch might not be turned on correctly.
- The battery might be low on power or improperly installed.
Solutions:
- Unlock the flashlight by following the lockout mode instructions in the user manual.
- Double-check if the switch is correctly turned on.
- Try charging the battery or reinstalling it correctly.
Issue: Abnormal Noise
Possible Cause:
- There may be damage to certain parts of the flashlight.
- There may be presence of foreign matter in the tube.
Solution:
- If any parts of the flashlight are damaged, please reach out to your local distributor for assistance.
- Ensure to remove any foreign matter from the flashlight’s tube.
Caution
- Prior to using the product, kindly read the user manual carefully.
- Exercise caution as the product may generate heat during operation to prevent any potential harm.
- Avoid direct exposure of the light to the eyes to prevent eye damage.
- Keep the product out of reach of children.
- Utilize WUBEN or WUBEN recommended batteries for optimal performance.
- Refrain from disassembling the product to maintain coverage under the WUBEN warranty policy.
- Do not dispose of the product in fire.
- Note that this product is not designed for prolonged underwater use and should not be used underwater for an extended period.
Warranty Conditions
A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:
- Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.
- Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).
- Natural wear and aging of consumables or components during use (such as batteries, etc.).
- Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
- If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.
EU Declaration of Conformity
This equipment is in compliance with the essential requirements and other
relevant provisions of EU directives.
WEEE
This product must not be disposed of as normal household waste in accordance
with the EU Directive on Waste Electrical and Electronic Equipment (WEEE –
2012/19 / EU). Instead, it shall be returned to the place of purchase or
handed over to a public collection point for the recyclable waste. By ensuring
this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. Contact
your local authority or the nearest collection point for further details.
Improper disposal of this type of waste may result in fines in accordance with
national regulations.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>