Consciot CL17001196 Ceiling Fan With Lights Installation Guide
- June 15, 2024
- Consciot
Table of Contents
Installation & Operating Instructions for the
Owner’s Installation ,Manual Waldo
Model No: Cl17001196
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
PACKAGE CONTENTS
HARDWARE CONTENTS
AA | Mounting bracket screws | 2 |
---|---|---|
BB | Spring washers | 2 |
CC | Flat washers | 2 |
DD | Plastic wire nut | 3 |
EE | Balancing kit | 1 |
FF | Blade screws | 16 |
GG | Blade washers | 16 |
HH | Light kit ball | 8 |
II | Light kit screws | 8 |
JJ | Light kit rubber stopper | 8 |
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
- Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers.
- Make sure all electrical connections comply with local codes, ordinances, the National Electrical Code and ANSI/NFPA 70-199. Hire an electrician or consult a do-it-yourself handbook if you are unfamiliar with installing electrical wiring.
- Make sure the installation site you choose allows a minimum of 7 feet from the blades to the floor and at least 30 inches from the tip of the blades to any obstruction.
- The weight of the fan is 16.53 pounds.
DANGER: When using an existing outlet box, make sure it is securely
attached to the building structure and can support the full weight of the fan.
Failure to this can result in serious injury or death. The stability of the
outlet box is essential in minimizing wobble and noise in the fan after
installation is complete.
WARNING: To avoid personal injury, the use of gloves may be necessary
while handling fan parts with sharp edges.
WARNING: To reduce the risk of fire, electric shock or personal injury,
mount the fan to an outlet box marked “ACCEPTABLE FOR FAN SUPPORT” and use the
mounting screws provided with the outlet box. Most outlet boxes commonly used
for the support of lighting fixtures are not acceptable for fan support and
may need to be replaced. Consult a qualified electrician if in doubt. Secure
the outlet box directly to the building structure. The outlet box and its
support must be able to support the moving weight of the fan (at least 35
Ibs.).
**WARNING: To reduce the risk of fire, electric shock or personal
injury, wire connectors provided with this fan are designed to accept only one
12-gauge house wire and two lead wires from the fan. If your house wire is
larger than 12-gauge and/or there is more than one house wire to connect to
the two fan lead wires, consult an electrician for the proper size wire
connectors to use.
****WARNING: To reduce the risk of fire, electric shock or personal
injury, do not bend the blade arms when installing them, balancing the blades
or cleaning the fan. Do not insert objects between the rotating fan blades.
****WARNING: To reduce the risk of personal injury, use only parts
provided with this fan. The use of parts other than those provided with this
fan will void the warranty.
CAUTION: Be sure the outlet box is properly grounded or a ground (green
or bare) wire is present.
CAUTION:** Carefully check all screws, bolts, and nuts on the fan assembly
ensure they are secured.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Please note changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CARE AND MAINTENANCE
At least twice each year, lower the canopy to check the downrod assembly and
tighten all screws on the fan. Clean the motor housing and blades with a soft
brush or lint-free cloth to avoid scratching the finish.
IMPORTANT: Shut off the main power supply before you begin any
maintenance task. Do NOT use water or a damp cloth to clean the fan.
PREPARATION
Before beginning the assembly of this product, ensure all parts are present.
Compare all parts with the package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Estimated assembly time: 40-60 minutes
-
Turn off power to the fan at the breaker box and the wall switch (Figure 1.1).
DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death. -
Choose one of the following mounting options (Figure 1.2) :
Standard Mount – best suited for ceilings 8 feet or higher. For very high ceilings, use a longer downrod (not included).
Angle Mount – best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary to ensure proper blade clearance. Ensure the ceiling angle is not steeper than 15 degrees.
Flushmount Installation – not available for this model.
Closemount Installation – not available for this model. -
Choose a suitable location – Ensure the blades will be at least 30 inches from any obstructions. Also check the downrod length to ensure the blades will be at least 7 feet above the floor (Figure 1.3).
TOOLS & MATERIALS REQUIRED
INITIAL INSTALLATION
NOTE: Before discarding packaging materials, be certain all parts have
been removed.
NOTE: Place the parts from the hardware bag into a small container to
keep them from being lost.
INSTALLATION
REMOTE CONTROL
1. Fan ON/OFF
2. All OFF
3. Light ON/OFF
4. 1st Speed
5. 2nd speed
6. 3rd speed
7. 4th speed
8. 5th speed
9. 6th speed| 10. Reverse Switch
11. Light Dimming –
12. Light Dimming +
13. 2H timer for Fan
14. 4H timer for Fan
15. 8H timer for Fan
16. 60 seconds timer for light
17. Natural wind
---|---
AFTER INSTALLATION
WOBBLE
The fan blades have been adjusted in the factory to minimize any wobble
NOTE: CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT
THEY ARE MOUNTED ONA RUBBER GROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE
CEILING, IT WOULD CAUSE EXCESS VIBRATION. MOVEMENT OF A FEW CENTIMETERS IS
QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM. TO REDUCE THE FAN WOBBLE:
PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE MOUNTING BRACKET AND DOWNROD
ARE SECURE.
BALANCING A WOBBLING CEILING FAN:
For your convenience, a Balancing Kit is included; please follow this
procedure when balancing the fan:
- Check that all blade and blade arm screws are secure.
- Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure this distance.Rotate the fan until the next blade is positioned for measurement. Repeat for each blade. The distance deviation should be equal to 1/8″(0.32cm).
- Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable.
- If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE ARM
WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO NOT INSERT
FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.
NOISE
When it is quiet(especially at night) you may hear occasional small noises.
This is normal. Please allow a 24-hour “breaking-in” period, most noises
associated with a new fan disappear during the time.
CARE AND CLEANING
- Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to avoid scratching the paint finish. Please make sure to turn off electrical power before you clean your fan
- Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock.
- Motor has permanently lubricated ball bearing. No need to oil
NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT ANY CLEANING OR REPAIRS.
Questions, problems, missing parts?
Before returning to the store, contact
Consciot Customer Service.
Email:support@consciot.com
Tel:+1(866) 698-6211(Mon.- Fri.9 to 5 PST)
Documents / Resources
|
Consciot CL17001196 Ceiling Fan With
Lights
[pdf] Installation Guide
CL17002-D52-US, 530386, CL17001196, CL17001196 Ceiling Fan With Lights,
Ceiling Fan With Lights, Fan With Lights, Lights
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>